76
0UZ[HSSH[PVU
Wired Remote Control Mounting Locations
Passenger Compartment Mounting
The wired remote controller needs to be mounted in a location that is readily accessible to the driver. The remote is used to control a number of functions
such as main volume, sub volume, Punch EQ, source selection, EQ preset selection. The remote cannot be used when the processor is connected to a PC.
Once connected to a PC the remote simulator assumes all control from the wired remote level control.
Wiring the system
If you do not feel comfortable with wiring your new unit, please see your local Authorized Rockford Fosgate Dealer for
installation.
Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury.
Avoid running power wires near the low level input cables, antenna, power leads, sensitive equipment or harnesses. The power
wires carry substantial current and could induce noise into the audio system.
INPUT Connections
1. Plan the wire routing. Keep RCA cables close together but isolated from power cables and any high power auto accessories, especially electric motors.
This is done to prevent coupling the noise from radiated electrical fields into the audio signal. When feeding the wires through the firewall or any metal
barrier, protect them with plastic or rubber grommets to prevent short circuits. Leave the wires long at this point to adjust for a precise fit at a later time.
2. Securely mount the 3Sixty.3 unit to the vehicle using the supplied hardware. Please refer to the “Mounting locations” section on page 6 to select a good
location. Always check the opposite side of the mounting surface to ensure that there is nothing that can be damaged before fastening the unit down.
3. Prepare the BLK wire (ground cable) for attachment to the power connector harness. Solder or crimp connect the BLK ground wire from the vehicle to the
BLK ground wire from the 4 pin harness. Prepare the chassis ground by scraping any paint from the metal surface and thoroughly clean the area of all dirt
and grease. Solder or crimp a ring connector to the other end of the wire and fasten the cable to the chassis using a non-anodized screw and a star washer.
NOTE: Keep the length of the BLACK wire (Ground) as short as possible.
4. Prepare the RED wire (power cable) for attachment to the power connector harness. If you are connecting directly to the battery, or a high current circuit
ensure the wire is equipped with a 5A fuse. Solder or crimp connect the RED (B+) wire from the vehicle to the RED (B+) wire from the 4 pin harness.
5. Prepare the BLUE wire (REM OUT) for attachment to the power connector harness. Solder or crimp connect the BLUE wire from the amplifier(s) (REM IN)
to the BLUE wire from the 4 pin harness.
NOTE: The BLUE wire (REM OUT) can turn on up to three amplifiers without the use of an external relay.
6. Prepare the BLUE/WHT wire (REM IN) for attachment to the power connector harness. Solder or crimp connect the BLUE/WHT wire from the head units
(REM OUT) to the BLUE wire from the 4 pin harness.
NOTE: The BLUE/WHT wire (REM IN) can also be connected to the vehicles +12V ACC power for vehicles without an aftermarket head unit.
NOTE: For systems using high level inputs the 3Sixty.3 is equipped with signal sensing turn on, in which case the BLUE/WHT wire is not used. The
signal sense circuit is on channel 1, so channel 1 must be connected and must see a 6VDC offset to turn the unit on.
7. Insert the power connector into the Power Input port on the 3Sixty.3.
0UZ[HSSH[PVU
Installation Considerations
As the automotive manufacturers increasingly make their source units (radios) an integral part of the vehicle, it becomes increasingly harder to change
them out and upgrade your system. The 3Sixty.3 makes it possible to utilize the vehicle source unit and still create the sound experience that fits you. With
an easy to use interface, the 3Sixty.3 connected to your vehicle’s source unit and an amplifier, you can create a sound stage that is personally tuned to your
vehicle. The 3Sixty.3 gives you all the benefits of creating the best system possible without compromising the manufacturer’s integrated source system.
IMPORTANT To tune the 3Sixty.3 properly to your system the source unit must have a CD player, an amplifier with RCA inputs and a PC is also
required for initial setup and adjustments.
The following is a list of tools needed for installation:
This section focuses on some of the vehicle considerations for installing your new system.
Pre-planning your system layout and best wiring routes will save installation time. When deciding on the layout of your new system, be sure that each
component will be easily accessible for making adjustments.
If you feel unsure about installing this system yourself, have it installed by a qualified technician.
Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury.
Before beginning any installation, follow these simple rules:
1. Be sure to carefully read and understand the instructions before attempting to install the unit.
2. For safety, disconnect the negative lead from the battery prior to beginning the installation.
3. For easier assembly, we suggest you run all wires prior to mounting your unit in place.
4. Route all of the RCA cables close together and away from any high current wires.
5. Use high quality connectors for a reliable installation and to minimize signal or power loss.
6. Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when
working on any vehicle.
7. Never run wires underneath the vehicle. Running the wires inside the vehicle provides the best protection.
8. Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the
firewall.
9. ALWAYS protect the battery and electrical system from damage with proper fusing. Install the appropriate fuse holder and fuse on the +12V power
wire within 18” (45.7 cm) of the battery terminal.
10. When grounding to the chassis of the vehicle, scrape all paint from the metal to ensure a good, clean ground connection. Grounding connections
should be as short as possible and always be connected to metal that is welded to the main body, or chassis, of the vehicle.
Processor Mounting Locations
NOTE: The BT dongle signal will greatly be reduced if the unit is mounted under or behind any metallic material.
Engine Compartment
Never mount this unit in the engine compartment. Mounting the unit in the engine compartment will void your warranty.
Trunk Mounting
The recommended orientation would be on the floor, as this would provide the best possible range for the Bluetooth controller. The device may be mounted
in any other orientation as long as Bluetooth range is maintained. Each vehicle is made of different materials and this may inhibit the Bluetooth range as
well. The less metal between the device and controller, the better the signal strength will be.
Passenger Compartment Mounting
This would be the ideal location for the device, as this would provide the optimal Bluetooth range.
Battery post wrench
Hand held drill w/assorted bits
1/8” diameter heatshrink tubing
Soldering iron & Soldier
Adequate Length—Red Power Wire
Adequate Length—Remote Turn-on Wire
Adequate Length—Black Grounding Wire
PC
Volt/Ohm Meter
Wire strippers
Wire crimpers
Wire cutters
Small Flathead screwdriver
#2 Phillips screwdriver
