Rockford Fosgate RFX4000 Bedienungsanleitung

◆DIGITAL AUDIO PLAYER

◆SIRIUS READY

◆AM/FM STEREO RADIO

◆

USB/SD MUSIC PLAY

BLUETOOTH STRAM

MODEL: RFX4000

CONTENTS

CONTENTS..........................................................

CONTROL PANEL ILLUSTRATION.........................

REMOTE CONTROL FUNCTION............................

WIRE DIAGRAM...................................................

INSTALLATION....................................................

BASIC OPERATION..............................................

SIRIUS OPERATION.............................................

RADIO OPERATION/AUX......................................

....................................

SPECIFICATION..................................................

TROUBLESHOOTING..........................................

USB/SD/CDC OPERATION

BLUETOOTH OPERATION

7-10

E2E15

Can not read some USB devices

The unit is not 100% compatible with all USB devices or the USB device has special

Try to format the USB device in FAT 16/32 standard.

format.

Can not play certain songs with specific formats that are downloaded from websites

Example:Tunes which is in DRM(digital right management) format is not supported by the

current unit.

Unit takes about 60 seconds to recognize some USB device

It is normal. The unit sometimes takes longer time to read all the files inside the USB device.

LCD Can Not display the MP3 song name correctly

The songs are in foreign language or not in ID3 Tag format.

Power does not turn on (no sound)

Check the wire.

Check the unit fuse. Replace new fuse if blown. If it happens again, consult the dealer.

No sound out put when operating the unit with amplifiers or power antenna is attached

Power antenna lead is shorted to ground or excessive current is required for amplifiers or

power antenna.

Button is not responsive or the LCD display is wrong.

The connection pins for the front panel may be dirt. Use a soft cloth to clean its surface.

If it does not fix the problem, consult your dealer.

The unit picks up the engine noise. Check the ground wire.

After turn the power on, the unit powers off immediately

The battery may be too low (The unit operating voltage is 11V to 16V).If the unit still cannot

turn on, consult your dealer.

WARRANTY INFORMATION:

Should this product require service, you may obtain specific information by contacting the

dealer from whom this product was purchased.

For any service related questions, please call our technical service team.

Technical Support Phone Number:574-293-1521

TROUBLESHOOTING

E3 E14

SPECIFICATION

TUNER(FM)

.....................................................87.5-107.9 MHz

Channel Step.......................................................... 200KHz

Sensitivity ............................................................8dB

Stereo Separation....................................................30dB

Signal to Noise Radio................................................60dB

Frequency Range

TUNER(AM)

....................................................530-1710 KHz

Usable Sensitivity....................................................32 dBuV

Channel Step..........................................................10KHz

Signal to Noise Radio...............................................50dB

Frequency Range

LINE-OUT

Impedance...........................................................33 Ohm

Output..................................................................3 Volt ( max )

GENERAL

..........................................................13.8V DC (10-15.6V allowable)

Speaker Impedance................................................. 4 or 8 ohm

Output Power........................................................... 50W x 4CH

Fuse........................................................................10A

Power Supply

Note: Specifications and the design are subject to possible modification

without notice due to improvement.

E13 E4

If the fuse blows, check the power connection and replace the fuse. If the fuse

blows again after the replacement, there may be an internal malfunction. In this

case, consult your nearest repairing center.

Fuse replacement

Warning:

Only replace fuse with the same type and rating. Use of a different

type or rating may cause serious damage.

Be sure your wire remote(RFX-MR3/RFX-MR6) is installed correctly,

wrong connection will cause serious damage to the wire remote.

WIRE DIAGRAM

BLUETOOTH DONGLE

DIGI PORT

BLUETOOTH OPERATION

MODEL: RFX4000BT

Installation Note for Bluetooth Dongle

To get better signal, the Bluetooth Dongle needs to be installed near the surface and

must avoid a metal surface.

If the Dongle is installed under a metal surface or deep inside, it may hare a poor

Bluetooth signal.

Bluetooth mode select

Press the MODE(4) button and select the Bluetooth mode .

Make sure the Bluetooth Dongle is connected to the appropriate port on the unit.

Pairing with a Bluetooth device

The unit is ready to pair when the BT mode is selected.To pair your device to the

unit,make sure you are close enough to the unit.

1. Open the Bluetooth setting on your device,

2. Choose "RFX4000" from the list of the available Bluetooth link,

3. Enter "0000" as the Bluetooth passwork.

Play the Bluetooth music

When you succeed in pairing the Bluetooth device,you can play the Bluetotth music

on your device.

a. Press the previous/next key to change the track.

b. Press the play/pause key to start or pause the audio.

c. Press and hold A/PS key to disconnect the current Bluetooth device from the unit,

but this will not erase the pairing from unit memory.

d. Press and hold BAND key s to erase all Bluetooth pairings stored in the uint

memory. .

(BLUETOOTH DONGLE)

1. Precautions

Choose the mounting location carefully so that the unit will not interfere with the

normal driving functions of the boat.

Avoid installing the unit where it would be subject to high temperature, such as

from direct sunlight or hot air , or where it would be subject to dust, dirt or excessive

vibration.

Use only the supplied mounting hardware for a safe and secure installation.

INSTALLATION

Correct mounting positions

Incorrect mounting positions

Better: 45 facing upward Best: 90 facing upward

Do not mount black box in either

of the following positions, this

will allow water to intrude and

will result in damage to the unit.

2. Mounting illustration

3. Installation Note

Please find enclosed nylon wire tie-downs(wire clamps)for added support.

use the wire clamps to hold down the harness, preventing water from running

along the wires and into the unit.

E12

USB PORT

When a USB device with audio files is plugged, the unit will play the audio files

automatically. You may use SCAN as "10+" button and BAND as "10-" button for

fast search during the USB operation.

USB

our

The marine unit can support playing the music in by inputting the song

sequence number directly: when the unit is playing songs, press AS/PS button

on the front panel, it will display "SCH 0000" on the LCD, the f digits indicates

the sequence number that you want to listen to. You can use preset key 1,2,3,4,

to set the f digits by pressing them repeatedly and press SEL to confirm input,

the unit will start playing the new song automatically.

USB/SD/CDC OPERATION

IMPORTANT NOTE:

Because of the great variety of products with USB port and sometimes quite

manufacturer-specific functions we can neither guarantee that all devices will

be recognized nor that all operating options that are possible in theory will

actually work.

devices may take more than 45 seconds to initiate after plugging in.Some USB/SD

Notes for CD

(1) Keep the disk clean and undamaged, do not stick things on the dis .

(2) Do not play the damaged or transformative disc, keep the disc correctly .

(3) Do not keep the disc under sunshine or in high temperature environment .

(4) Put the disc into its box after using.

(5) Finger mark or besmirch will effect the disc playing quality, it can't be cleaned

by soft cloth. If it is necessary , diluted natural solvent can be used to help clean

the disc. Record cleaner or antistatic solvent can't be used to clean the disc.

CDC Operation

(1) Press to power on.

(2) Connect the CDC to your unit, then press "MODE" to CDC mode.

(3) The LCD will display "disc style" " item number" "playing time".

( 4) Press " " to pause the playing.

(5) Press PRESET 2 (11) to enter REPEAT playing mode.

(6) Press PRESET 3 (12) to enter RANDOM playing mode.

(7) Follow the function key instruction to do the operation.

(8) You may press SCAN as "next- disc" button and BAND as "pre-disc" button

for change disc operation.

SD PORT

When a SD card with a card-reader is plugged, the unit will turn to the SD mode and

play the audio files that in the SD card automatically.

The SD mode has the same function as the USB mode.

POWER ON/OFF(1)

Press the button to turn the unit on or off .

SELECT (2)&VOLUME UP/DOWN(3)

Repeatedly press SEL button to select

ID3→VOL, then you can use the VOL +/- button to change the setting.

BAS→TRE→BAL→FAD→SUB→EQ→

BASIC OPERATION

Long press SEL button to enter zone selection, and short press it again repeatedly

to select channel switch, Beep setting, trigger 1/trigger 2 setting, press the

VOL + / - to change the settings.

a ZONE: AMERICA / EUROPE / CHINA .

b STEREO/MONO SWITCH: FM mode.

c Beep : Activate Beep on/off.

d TRI 1 : Activate Trigger 1(12V_1) on/off.

e TRI 2 : Activate Trigger 2(12V_2) on/off.

MODE button (MODE) (4)

Press to switch mode: SIRIUS/CDC/AUX/TUNER/DIGI PORT/USB ./SD/BT

LCD display (17)

Display the current state of the unit.

Adjust back light(MENU) (16)

By pressing MENU key more than 2s , you can adjust back light.(25%,100%)

DISPLAY (DISP) (5)

Press DISP button once to display the system time on the LCD.

a. Press and hold DISP button until hour digit starts blinking, use / to

adjust hour.

b. Press DISP again, minute digit starts blinking, use / to adjust minute.

Low Voltage Warning

When the power supply drops down to 10V, it will display BATTERY LOW

on LCD and beeps for 1 minute, the black box will be turned off automatically

in 1 minute.

LOCK THE CONTROL PANEL

Press and hold “SEL” (2)and “DISP”(5) buttons together for 3 seconds

to lock the RFX-MR5BB control panel, the Black Box will not response the button

press on the panel when the panel is locked. Press and hold “SEL” and “DISP”

buttons for 3 seconds again to unlock the RFX,MR5BB control panel.

" "

E11

Listening to the radio

Press the MODE (4) button and select the radio mode, the frequency appears

in the display.

Press the BAND (8) button and select the radio band FM1~FM2~FM3~AM1~AM2.

Tuning

There are 3 types of tuning mode available: SEEK tuning, MANUAL tuning and

Preset stations.

Auto Seek a Station

Press the BAND (8) button and select the desired band (FM or AM).

Press or to start to seek a station.

Manual Tuning

Press the or button longer than 2s, change . will to manual tuning mode

Storing a Station

Select a band (if needed), then select a station.

Press and hold a Preset button 1-6 for more than 2 seconds, the current station

will be stored to the number.

Automatic Tuning Control (SCAN) (9)

In radio mode, press SCAN button to scan stations, the unit will pause for 5 seconds

at each strong radio station. At the desired station press the SCAN again to stop

scanning.

RADIO OPERATION /AUX

Radio Operation

A/PS(7)

Short

it pauses for 5 seconds at each preset station.

Long press A/PS button, the unit will search six strong stations and automatically

store them on buttons 1-6.

press A/PS button, the unit will scan stored stations in the current band,

AUX IN PORT

For iPod, MP3 players, and other portable media players.

SIRIUS OPERATION

This unit is compatible with a variety of SIRIUS Satellte Radio solutions

including the SCC1 Sirius Connect Vehicle Tuner and SCVDOC1 Sirius

Connect Vehicle Kit with any compatible SIRIUS Dock & Play radio. The

operation will be the same regardless of the SIRIUS radio is used .

Sirius Operation

◆

1) POWER ON/OFF

2) SEL: Function Select button

3) VOL+/-: Volume set button

4) MODE: Switch between different modes

5) DISP: Display the SIRIUS channel info

6) SEEK+/-: Short press to select previous/next station, Long press (more than

2 seconds) to switch channel rapidly

7) AS/PS: Short press to input channel number directly

8) BAND: Switch between SR1, SR2 and SR3

9) SCAN: Short press to LOCK/UNLOCK channels, Long press to change

the password.

10) Preset 1: For preset station 1

Also used to input the first digit of pass code or channel #.

11) Preset 2: For preset station 2

Also used to input the second digit of pass code or channel #.

12) Preset 3: For preset station 3

Also used to input the third digit of pass code of channel #.

13) Preset 4: For preset station 4

Also used to input the fourth digit of pass code

14) Preset 5: For preset station 5

15) Preset 6: For preset station 6

16) MENU: Short press to turn on/off Category.

When category is on, you can press "SEL" key to select between

categories and then seek in current selected category by pressing

SEEK+/- key.

17) LCD DISPLAY

1. Button definitions

◆ User needs follow the instruction of SCCI or SCVDOC1 for installation.

Always make sure the Sirius SIRIUS antenna is connected properly located

for maximum signal reception.

E10

SIRIUS OPERATION

7. Display channel information:

Press DISP button repeatedly to display different information of the channel such

as channel #, channel name, category, song title, artist, composer...

8. Message display:

Check Sirius Tuner : Tuner is not connected or is bad.

Antenna Error A n t enna is bad or not connected.

Acquiring signal N o signal output from the Sirius TUNER

"Updating " Updates the Sirius information into unit.

FW Updating U p d a tes firmware

Subscription updating Updates subscription

Updating Channels Updates the GCI(Channel info)

" "

IMPORTANT NOTE:

Because of the great variety of products with USB port and sometimes quite

manufacturer-specific functions we can neither guarantee that all devices will

be recognized nor that all operating options that are possible in theory will

actually work.

some USB devices may take more than 45 seconds to initiate after plugging in.

2.Sirius ID and Activate Sirius service

After system is turned on, press the MODE button to enter the SIRIUS mode.

The system will display a "SIRIUS" logo on the LCD screen.

Until you subscribe and activate the SIRIUS service, you can only access

channel 0 (the SIRIUS ID channel) and 184 (Preview Channel).

Tune to Channel 0 to display your radio's unique 12-digit SIRIUS ID number (SID).

This number is also available on the back of SIRIUS Tuner SCC1. Write down

this number and call 1-888-539-SIRIUS (1-888-539-7474) with your credit card

handy to activate SIRIUS service.

You may go to website https://activate.siriusradio.com// to activate the service.

If you do not subscribe the full service, the unsubscribed channel will display

"CALL 888-539-SIRIUS to subscribe"when tuned.

SIRIUS OPERATION

3. Preset Stations

The unit has total 18 preset stations in SIRIUS Mode. Use BAND button to switch

between SR1, SR2, and SR3. Each band has 6 preset stations.

Short press the Preset 1~6 button to listen to the preset stations.

Long press the preset 1~6 button to store current station to preset memory.

4. Select channels by category

Short press MENU button to turn on/off the category mode. A "CAT" icon in the

LCD will indicate the Category mode is on. When Category mode is on, long

press "SEEK +/-" to switch between the categories, such as POP,ROCK,

COUNTRY, etc. And you can switch channels in selected category by short

pressing "SEEK+/- " button. The category mode will not time out unless you

turn off this mode by short press MENU button again.

5. Input channel directly.

Short press the AS/PS key to enter the direct input mode. The LCD will display:

"CH X X XX " Press Preset 1 repeatedly to select the first digit of channel number

(the first digit changes incrementally from 0, 1, 2).

Press Preset 2 repeatedly to select the second digit of channel number(the second

digit incrementally from 0, 1, 2, ... To 9)

Press Preset 3 repeatedly to select the third digit of the channel number (the third

digit changes incrementally from 0, 1, 2, ... To 9).

When 3 digits are selected, press "SEL" button to enter the desired channel.

6. Parental Control

You can lock any Sirius channels you do not others to have access without your

permission. The default code is "5220"if you forget your pass code, you may

disconnect the unit completely from power. The unit will restore to the default

pass code after power on again. Enter a Locked channel: When user tunes to

a locked channel, the LCD screen will display: "LOCKED CH" first and then display:

"CODE X X X X".

Press Preset 1 repeatedly to select the first digit of pass code.

Press Preset 2 repeatedly to select the second digit of pass code.

Press Preset 3 repeatedly to select the third digit of pass code.

Press Preset 4 repeatedly to select the last digit of pass code.

When all digits are selected, press "SEL" button will enter the channel.

If the code is wrong, it will display "CODE X X X X" again and wait for user to enter

code again. If user enters a wrong code again, the unit will display "PWD ERROR"

and go back to previous screen.

Note: user needs wait for "CODE X X X X" display to enter pass code. Otherwise

the Preset 1-4 still enters as Preset station.

To lock a channel:

When a channel is selected, use "SCAN" to lock this channel. The LCD will display

"LOCK CH" first and then display: "CODE X X X X".Use Preset 1-4 (same as above)

to enter pass code and press SEL to lock.

Note: After a channel is locked, user cannot tune to this channel by SEEK+/- button.

User must input the channel # directly to enter this channel.

To unlock a channel:

User needs enter the locked channel first and then short press "SCAN"button.

The LCD will display "UNLOCK CH" and then display: "CODE X X X X".

Same procedure as above to enter the code and unlock the channel.

To change pass code:

Long press "SCAN"button to change the pass code. The screen will display

"OLD CODE"shortly and then display "CODE X X X X" Use Preset 1~4 buttons

as above to enter the pass code.

If the old pass code is entered correctly, the screen will display "NEW CODE" and

then display: "SET X X X X" Use Preset 1-4 buttons again to set up a new pass code.

SIRIUS OPERATION

Inhaltsverzeichnis

Andere Rockford Fosgate Medienplayer Handbücher

Rockford Fosgate

Rockford Fosgate RFX4000-SX Bedienungsanleitung

Beliebte Medienplayer Handbücher anderer Marken

Visual Land

Visual Land Impulse Bedienungsanleitung

Transcend

Transcend DMP10 Bedienungsanleitung

Philips

Philips GoGear Muse SA2MUS08 Bedienungsanleitung

Fantec

Fantec MM-HDRL Bedienungsanleitung

Dune HD

Dune HD Duo 4K Bedienungsanleitung

IAdea

IAdea HMP-505S Bedienungsanleitung

Camos

Camos MMS-1000 Bedienungsanleitung

Energy

Energy 75 Series Bedienungsanleitung

Z3 Technology

Z3 Technology DME-03 Bedienungsanleitung

Sony

Sony SVR-2000 Benutzerhandbuch

Meicheng

Meicheng HD-1080K12 Bedienungsanleitung

DENAFRIPS

DENAFRIPS ARCE Bedienungsanleitung

Topaz

Topaz CMS Media Player Gebrauchsanweisung

InFocus

InFocus LightCast Bedienungsanleitung

IconBiT

IconBiT XDS1003D Bedienungsanleitung

Quanmax

Quanmax QDSP-2090 Series Bedienungsanleitung

Samsung

Samsung MP-80S Bedienungsanleitung

Trigon Elektronik

Trigon Elektronik CHRONOLOG Bedienungsanleitung