Rockwell Automation Allen-Bradley TLP-SSN-F046 Bedienungsanleitung

Installation Instructions

Original Instructions

Shaft Seal Kits for Kinetix TLP Servo Motors

Catalog Numbers

TLP-SSN-F046, TLP-SSN-F070, TLP-SSN-F090, TLP-SSN-F100, TLP-SSN-F115,

TLP-SSN-F145, TLP-SSN-F200, TLP-SSN-F235

Topic Page

About Shaft Seals 2

Required Tools 2

Required Supplies 2

Remove the Shaft Seal 3

Replace the Shaft Seal 4

Shaft Seal Kit Catalog Numbers 6

Additional Resources 7

2Rockwell Automation Publication 2090-IN044B-EN-P - September 2019

Shaft Seal Kits for Kinetix TLP Servo Motors

About Shaft Seals

A shaft seal is recommended if the motor shaft and end bell are exposed to significant amounts of

containments, such as oil, fluids, or fine dust. Use a shaft seal in these environments to prolong

the life of the motor. A shaft seal and Bulletin 2090 cables with environmentally sealed

connectors are required for an IP65 rating or greater.

See Kinetix® Motion Accessories Specifications Technical Data, publication KNX-TD004, to

find Bulletin 2090 cables with environmentally sealed connectors for your motor.

Required Tools

Use these tools to install a shaft seal:

• Insulated, small, flat-head screw driver

• Rubber/wooden mallet or a metal hammer and wooden work piece

• Socket, pipe, or tube (various sizes)

• Abrasive cloth to remove any nicks or burrs from the motor shaft

Required Supplies

Lubricant - Grease, industrial grade, suitable for applications with speeds up to 6000 RPM, and

–10…+80 °C (14…176 °F) temperature range.

IMPORTANT The shaft seal is not required in applications where the motor shaft and end bell are free of oil,

fluids, or fine dust, and a lower IP rating is sufficient.

Shaft seals are subject to wear and require periodic inspection and replacement. Replacement

is recommended every 3 months, not to exceed 12 months, depending on use.

If you paint the motor, do not get paint on the shaft seal area or the shaft, as paint can decrease

the life of the shaft seal.

Oil, Fluids, and Fine Dust Oil, Fluids, and Fine Dust

Shaft Seal Installations

Recommended

Shaft Seal Installation

is Not Recommended

Motor Shaft and

End Bell are Exposed

to Containments

Motor Shaft and

End Bell are Protected

From Containments

Shaft Seal Installation

is Not Recommended

Rockwell Automation Publication 2090-IN044B-EN-P - September 2019 3

Shaft Seal Kits for Kinetix TLP Servo Motors

Remove the Shaft Seal

Follow these steps to remove the shaft seal.

1. Remove power to the motor before removing the shaft seal.

2. Remove the shaft key (if present) from the motor shaft.

3. Remove old seal.

Place the insulated screw driver on the inside diameter of the shaft seal outer lip as

shown. Carefully lift the seal, work your way around the seal lift a little at a time. When

you can grasp the seal, slightly rotate it while pulling it out of the front-end bell.

4. Inspect and clean the shaft and seal surfaces as necessary.

Use an abrasive cloth to remove any nicks or burrs from the motor shaft.

ATTENTION: To avoid injury or damage to the equipment, remove power from the motor before

removing the shaft seal.

ATTENTION: Avoid damage to the motor. Do not pry against front-end bell or shaft.

ATTENTION: Do not hammer the shaft or body of the motor when changing the shaft seal.

Do not remove screws.

Do not pry against

front-end bell or shaft.

Outer Lip

4Rockwell Automation Publication 2090-IN044B-EN-P - September 2019

Shaft Seal Kits for Kinetix TLP Servo Motors

Replace the Shaft Seal

Follow these steps to replace the shaft seal.

1. Apply tape to the keyway so the edges do not damage the seal lip.

2. Lubricate the motor shaft and the inner and outer lip of the shaft seal.

3. Center the shaft seal on the mounting surface of the motor and slide the shaft seal evenly

onto the motor shaft.

See Shaft Seal Installation Clearances on page 5 for the correct installation clearance of

the shaft seal you are installing.

4. Press the shaft seal into the seal bore by applying one of the Shaft Seal Installation

Methods on page 6.

5. Visually inspect for irregularities in the shaft seal or an uneven alignment where the shaft

seal contacts the motor.

Verify that the outer and inner circumference of the shaft seal is fully seated into

position.

6. Verify that the shaft seal is installed to the correct installation clearance.

• If the shaft seal is installed too deep, it can become subject to excessive wear and

require frequent replacement.

• If the shaft seal is installed too shallow, it can reduce the effectiveness of the

protective seal.

7. Replace the shaft key.

Applies to motors that include a keyed shaft.

IMPORTANT Cover the sharp edges of the keyway with tape to protect the shaft seal lip from

damage.

IMPORTANT Shaft seals require a lubricant to reduce wear. Lubricate only the inner and outer lip

of the shaft seal. Do not lubricate the motor bore or outside diameter of the seal.

Back View of Shaft Seal

(motor facing)

Inner Shaft Seal Lip

Outer Shaft Seal Lip

Rockwell Automation Publication 2090-IN044B-EN-P - September 2019 5

Shaft Seal Kits for Kinetix TLP Servo Motors

Shaft Seal Installation Clearances

Motor Cat. No.

Shaft Seal Installation Clearance

Min, mm (in.) Nom, mm (in.) Max, mm (in.)

TLP-A0xx Press the shaft seal so that the seal is flush with the front surface of the motor.

TLP-A1xx and TLP-A2xx 0.00 (0.00) 0.10 (0.004) 0.20 (0.008)

Front Surface

of Motor

Shaft Seal Pressed

Flush with Front

Surface of Motor

Shaft Seal Pressed

Below Front

Surface of Motor

Front Surface

of Motor

Nom

Min

Max Bulletin TLP-A0xx

Shaft Seal Example

Bulletin TLP-A1xx and TLP-A2xx

Shaft Seal Example

Shaft Seal

Shaft

Shaft Seal

6Rockwell Automation Publication 2090-IN044B-EN-P - September 2019

Shaft Seal Kits for Kinetix TLP Servo Motors

Shaft Seal Installation Methods

Shaft Seal Kit Catalog Numbers

ATTENTION: Do not hammer directly on the shaft seal. Gently tap the socket, pipe, or tube evenly

around the outer edge of the shaft seal until the shaft seal is pressed into place. Make sure the

socket, pipe, or tube you use does not contact the shaft seal lip. Permanent damage to the shaft

seal can occur.

IMPORTANT Third-party shaft seals are not approved for use with these motors.The use of third-party shaft

seals voids any implied or expressed warranties.

Kinetix TLP Low Inertia Motors

Motor Cat. No. Shaft Seal Kit Cat. No.

TPL-A046 TLP-SSN-F046

TPL-A070 TLP-SSN-F070

TPL-A090 TLP-SSN-F090

TPL-A100 TLP-SSN-F100

TPL-A115 TLP-SSN-F115

TPL-A145 TLP-SSN-F145

TPL-A200 TLP-SSN-F200

TPL-A235 TLP-SSN-F235

Socket, Pipe, orTube

(supplied by the customer)

Motor

Metal

Hammer

Shaft Seal

Wooden

Work

Piece

Rubber or

Wooden Mallet

Motor

Shaft Seal

Socket, Pipe, orTube

(supplied by the customer)

Rockwell Automation Publication 2090-IN044B-EN-P - September 2019 7

Shaft Seal Kits for Kinetix TLP Servo Motors

Additional Resources

These documents contain additional information concerning related products from Rockwell

Automation.

You can view or download publications at http://www.rockwellautomation.com/global/

literature-library/overview.page.

Resource Description

Kinetix Rotary Motion Specifications Technical Data,

publication KNX-TD001

Product specifications for Kinetix VP (Bulletin VPL, VPC, VPF, VPH,

VPS), MP-Series™ (Bulletin MPL, MPM, MPF, MPS), andTL-Series™

rotary motors.

Kinetix Motion Accessories Specifications Technical Data,

publication KNX-TD004

Product specifications for Bulletin 2090 motor and interface cables,

low-profile connector kits, drive power components, and other servo

drive accessory items.

Kinetix Motion Control Selection Guide,

publication KNX-SG001

Overview of Kinetix servo drives, motors, actuators, and motion

accessories that are designed to help make initial decisions for the

motion control products best suited for your system requirements.

Industrial AutomationWiring and Grounding Guidelines,

publication 1770-4.1

Provides general guidelines for installing a Rockwell Automation

industrial system.

Product Certifications website, rok.auto/certifications Provides declarations of conformity, certificates, and other

certification details.

Allen-Bradley, Kinetix, MP-Series, Rockwell Automation, Rockwell Software, and TL-Series are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400

Rockwell Automation maintains current product environmental information on its website at

http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.

Publication 2090-IN044B-EN-P - September 2019

5014099301-QO01

*QO01*

Rockwell Automation Support

Use the following resources to access support information.

Documentation Feedback

Your comments will help us serve your documentation needs better. If you have any suggestions

on how to improve this document, complete the How Are We Doing? form at http://

literature.rockwellautomation.com/idc/groups/literature/documents/du/ra-du002_-en-e.pdf.

Technical Support

Center

Knowledgebase Articles,

How-to Videos, FAQs, Chat,

User Forums, and Product

Notification Updates.

https://rockwellautomation.custhelp.com/

Local Technical

Support Phone

Numbers

Locate the phone number

for your country.

http://www.rockwellautomation.com/global/support/get-support-

now.page

Direct Dial Codes

Find the Direct Dial Code

for your product. Use the

code to route your call

directly to a technical

support engineer.

http://www.rockwellautomation.com/global/support/direct-dial.page

Literature Library

Installation Instructions,

Manuals, Brochures, and

Technical Data.

http://www.rockwellautomation.com/global/literature-library/

overview.page

Product

Compatibility and

Download Center

(PCDC)

Get help determining how

products interact, check

features and capabilities,

and find associated

firmware.

http://www.rockwellautomation.com/global/support/pcdc.page

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockwell Automation Motor Handbücher

Rockwell Automation

Rockwell Automation Allen-Bradley DC180ATZ Bedienungsanleitung

Rockwell Automation

Rockwell Automation 56 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Kinetix MMA-B080 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation MP-Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley MP-Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation ANORAD LZ Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 140G Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley MP-Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation MPL-B640 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley N Series Bedienungsanleitung

Beliebte Motor Handbücher anderer Marken

Rotax

Rotax 125 senior MAX evo Bedienungsanleitung

Kohler

Kohler K361 Bedienungsanleitung

MTD

MTD OHV Series Bedienungsanleitung

Kohler

Kohler COMMAND CH18-745 Bedienungsanleitung

Mercury

Mercury D4.2L D-Tronic Bedienungsanleitung

Selve

Selve SE Plus-RC Series Bedienungsanleitung

Perkins

Perkins 1206E-E66TA Bedienungsanleitung

Skov

Skov DA 174 Handbuch

Rossi

Rossi TX11 Series Bedienungsanleitung

Siemens

Siemens SIMOTICS T-1FW3 Merkblatt

AL-KO

AL-KO PRO 350 Bedienungsanleitung

MTU

MTU 12 V 4000 Lx4 Bedienungsanleitung

Nanni

Nanni N3.30 Gebrauchsanweisung

Nanni

Nanni N5.160 CR2 Bedienungsanleitung

KSB

KSB SuPreme Series Montageanleitung

Hiwin

Hiwin EM1 Series Bedienungsanleitung

Rotax

Rotax 912 i series Betriebsanleitung

Siemens

Siemens SIMOTICS XP 1MB1 Bedienungsanleitung