RodinBell D-100 Bedienungsanleitung

Shenzhen RodinBell Technology Co., Ltd.

D-100 UHF RFID Desktop Reader

User Manual V1.1

Catalogue

1. D-10X View ..................................................................................................................................3

1-1: Front View................................................................................................................................3

1-2: Back View.................................................................................................................................3

1-3: Plan View..................................................................................................................................3

2. Reader Configurations ...............................................................................................................4

2.1 Initial Use...................................................................................................................................4

2.1.1 Step 1: Connect The Reader to PC via USB or Serial Port.......................................................4

2.1.2 Step 4: Operating Reader via Demo ........................................................................................5

2.2 Setting RF Parameter ...............................................................................................................6

2.2.1 Setting RF Output Power.........................................................................................................6

2.2.2 Setting RF Spectrum................................................................................................................6

2.3 ISO-18000-6C tag inventory......................................................................................................7

2.3.1 Real Time Mode & Buffer Mode ...............................................................................................7

2.4 Accessing ISO-18000-6C Tag.................................................................................................10

2.4.1 Read tags ..............................................................................................................................10

2.4.2 Write Tags.............................................................................................................................. 11

2.4.3 Lock Tags............................................................................................................................... 11

2.4.4 Kill Tags .................................................................................................................................12

2.4.5 Tag Selection .........................................................................................................................12

2.4.6 Error Display Might Be Returned............................................................................................13

3. Develop your own RFID Application........................................................................................15

4. Installing Driver.........................................................................................................................16

1. D-10X View

1-1: Front View

1-2: Back View

1-3: Plan View

2. Reader Configurations

2.1 Initial Use

2.1.1 Step 1: Connect The Reader to PC via USB or Serial Port

Method NO.1: You can connect the reader to your PC via USB Cable, as illustrated below:

Next, please switch the DIP to the position as illustrated below:

Method NO.2: You can also connect the reader to PC via RS-232 serial port, as illustrated below:

Next, please switch the DIP to the position as illustrated below:

When the indicator light on and sound of a short beep, reader is ready.

Note: Driver will be installed automatically when reader is connected to PC for the first time. But

some computers may fail. In this case, please install driver manually. (please see: Installing

Driver at page 21).

2.1.2 Step 4: Operating Reader via Demo

Put the files that named UHFDemo.exe, reader.dll, customControl.dll into a same folder, and

double-click UHFDemo.exe to run the software.

1. Open the software and it will shows as below:

2. Please select RS232 as Connection if the reader is connected via RS -232 port, or select USB as

Connection if the reader is connected via USB. Choose the corresponding Serial Port and

Baudrate(default baudrate is 115200). As illustrated below:

3. Click Connect , if it succeeds, the Operation History will display as below:

4. Text communication with the reader:

Click on Get in Firmware Version or in Reader Identifier, the following screen displays:

Now the reader has been connected to PC successfully.

2.2Setting RF Parameter

After connecting the reader with PC, we need to set some basic RF parameters: RF Output Power & RF

Spectrum. Please select RF Setup as illustrated below:

2.2.1 Setting RF Output Power

RF Output Power is the strength of RF output signal from antenna port whose unit is dBm.

The output power range is 0 - 26dBm. When this setting completes, it will be saved in the reader

automatically even if the power is cut off. The default output power is 26dBm.

2.2.2 Setting RF Spectrum

Set the RF spectrum manually.

Please defer to Frequency parameter tablet in Communication protocol for more information about

the carrier frequency.

Frequency range the reader supports: 865MHz-868MHz(ETSI), 902MHz -928MHz(FCC).

You can set the reader in RF Spectrum Setup->User Define, as illustrate below:

Users can set RF spectrum via these three parameters: Start Frequency, Frequency Interval, The number

of Frequency points.

2.3 ISO-18000-6C tag inventory

Connect the Reader correctly. Tag operation could be started when RF Setup is completed.

Tag inventory means reader identifying multiple tags’EPC number at the same time. This is the core

function of UHF RFID Reader and one of the standards to judge a reader’s performance.

2.3.1 Real Time Mode & Buffer Mode

The most commonly used mode for tag inventory isReal-time Mode. Data will be uploaded meanwhile

you can get the tags’EPC number instantly. RSSI and Parameter of Frequency are changed and

recorded in real time. Due to its dual CPU architecture, performance of multi-tag identification under

Real-time mode is the best.

The other is Buffer Mode, the data will be cached and uploaded together when you need them. Under

this mode, the data are without repeat data and can keep in small volume, because the data will be

filtered before being uploaded. But it will take some time to filter duplicate data when reader identifies a

large number of tags. Therefore, its identification efficiency will be slightly lower than real-time mode. Note:

Tags can’t be operated when you extract data in the cache.

Users can choose the appropriate method based on actual situation as illustrated below:

Method NO.1: Real-time Mode

1. Click Tag Inventory (Real Time Mode). Select the connected antenna(s) port. Set the number of

Repeat Per Command, which is the times of repeat inventory command. For example, inventory

command will execute anti-collision algorithm one time when you set the value to 1. It will execute

anti-collision algorithm two times when you set the value to 2...

2. Click Inventory, you will find that the EPC number is uploaded immediately and it is real-time updating.

The reader will keep inventory until you click stop as shown below:

Inventoried Quantity

Total number of inventory tags since click on Inventory.

Speed

Speed of identification Tag, unit: piece / sec

Total Tag Communication

Total return EPC data of tags (Including repeated data)

Command Duration

Time of each inventory command takes, unit: ms

Total Inventory Duration

Total elapsed time since click on Inventory , unit: ms.

The serial number of data.

EPC

EPC number of tag.

Protocol Control word of tag.

Identification Count

Times of tag identified.

RSSI

The signal strength when tag was identified at the last time.

Carrier Frequency

Carrier frequency of tag which is identified at the last time.

Method NO.2: Buffer Mode

1. Click Inventory, the screen will display as below(single tag & multi-tag inventory):

Note: the identified tags won’t be shown in the Tag list.

2. Click Stop first, then click Get Buffer. All the data in cache will be uploaded as illustrated below:

Functions description under Buffer Mode:

Get and Clear: Read the data form cache and then clear the cache. It will be empty when you read the

cache again.

Query tag Quantity: If you just want to know how many tags are there in cache without details, click on

this button.

Clear Buffer: Clear the cache and refresh the screen.

2.4 Accessing ISO-18000-6C Tag

Click Access Tag, and the screen will display as following:

2.4.1 Read tags

You can set the parameter(zones to be read, StartAddress and Data Length) as illustrated below:

Note: the unit of Starting Address and Data Length is WORD which is 16 bit double-byte.

Click Read when the parameter setting is completed.

Picture as below shows that one tag has been identified successfully.

Inhaltsverzeichnis

Andere RodinBell Kartenleser Handbücher

RodinBell

RodinBell S-8600 Bedienungsanleitung

Beliebte Kartenleser Handbücher anderer Marken

Lindy

Lindy 43185 Bedienungsanleitung

Lindy

Lindy 43185 Bedienungsanleitung

ViziT

ViziT RD-4F Bedienungsanleitung

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Bedienungsanleitung

AVID ID

AVID ID AVID1043 Bedienungsanleitung

Conrad

Conrad PCMCIA Bedienungsanleitung

Rosslare

Rosslare DR-6255 Bedienungsanleitung

Lindy

Lindy 51541 Bedienungsanleitung

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Bedienungsanleitung

Johnson Controls

Johnson Controls Kantech tyco ioSmart Bedienungsanleitung

ACS

ACS ACR122L Bedienungsanleitung

Secukey

Secukey S2-MF Bedienungsanleitung

Elecom

Elecom MR-SMC07 series Bedienungsanleitung

Alien

Alien ALR-9800 Bedienungsanleitung

ACS

ACS ACR310 Bedienungsanleitung

Datamars

Datamars R-IN1300 MID Bedienungsanleitung

Alarm Lock

Alarm Lock AL-PRE2 Bedienungsanleitung

xpr

xpr B100PROX-AH Benutzerhandbuch