ROEL Alcar H51 Bedienungsanleitung

Installation Manual

. 50102/16.08.00 / V

ERSION

1.0

Auto Alarm System

TECHNICAL FEATURES

STAND-BY CURRENT CONSUMPTION ............................................................................................. MAX. 15mA

SIREN OUTPUT ............................................................................................................................ MAX. 1A

TRUNK RELEASE OUTPUT ....................................................................................................... MAX. 500mA

WINDOWS ROLL UP WHEN ARMING, OUTPUT .............................................................................. MAX. 500mA

ENGINE KILLER OUTPUT .......................................................................................................... MAX. 500mA

DOORS INPUT ................................................................................................................ NEGATIVE TRIGGER 1

TRUNK/HOOD INPUT ........................................................................................................ NEGATIVE TRIGGER 2

CENTRAL DOOR LOCK RELAYS ..................................................................................................... 10A/12V

REMOTE CONTROLS ............................................................................................................... HOPPING CODE

PROGRAMMABLE PARAMETERS ............................................................................................... 16 PARAMETERS

ALARM MEMORY ........................................................................................ ALARM TYPE DISTINCTLY INDICATED

DISABLING FAULTY SENSORS ............................................................................... SENSOR DISTINCT INDICATION

SYSTEM STATE MEMORIZED WHEN SWITCHING OFF POWER

Romano Electro Intl S.A.

27-29 Calimachi str., 72266, Bucharest,

Tel.:40-1-242.20.20, Fax:40-1-242.20.30,

E-mail: [email protected], www.roel.ro

Installation ManualAlcar®H51

TABLE OF CONTENT

CHAPTER I: INTRODUCTION ............................................................................................................. 3

CHAPTER II: THE KIT ..................................................................................................................... 3

CHAPTER III: GENERAL FEATURES .................................................................................................... 4

CHAPTER IV INSTALLATION ............................................................................................................. 5

4.1 SIREN MOUNTING ............................................................................................................................... 5

4.2 PIN SWITCH MOUNTING AT HOOD AND TRUNK ............................................................................................ 5

4.3 CENTRAL UNIT MOUNTING ......................................................................................................... 5

4.4 CONNECTIONS .................................................................................................................................. 5

4.4.1 Cable set A ........................................................................................................................................ 5

4.4.2 Cable set B ........................................................................................................................................ 5

4.4.3 Cable set C ....................................................................................................................................... 6

4.4.4 Dconnector ....................................................................................................................................... 8

4.4.5 Econnector ........................................................................................................................................ 8

4.4.6 Fconnector ........................................................................................................................................ 8

4.4.7 G Connector ..................................................................................................................................... 9

4.4.8 H connector ...................................................................................................................................... 9

4.4.9 Pager connecting ............................................................................................................................... 9

CHAPTER V: SYSTEM OPERATING ...................................................................................................... 9

5.1 LEARNING / CLEARING REMOTE CONTROLS .............................................................................................. 9

5.2 SYSTEM PARAMETERS PROGRAMMING ................................................................................................... 10

5.3 SERVICE MODE / EMERGENCY DISARMING .............................................................................................. 14

5.4 ENGINE KILLING ............................................................................................................................... 14

5.5 REMOTE CONTROL OPERATING ............................................................................................................ 14

5.5.1 Arming/disarming with confirmation by siren chirps and flashing lights ....................................... 15

5.5.2 Arming/disarming silent ................................................................................................................... 15

5.5.3 Remote controlled bypassing the sensors .................................................................................... 15

5.5.4 Arming with silent alarm .................................................................................................................. 16

5.5.5 Car finding ....................................................................................................................................... 16

5.5.6 Panic ................................................................................................................................................ 16

5.5.7 Signalling the remote controls number ........................................................................................... 17

5.5.8 Anti-carjacking mode ....................................................................................................................... 17

5.5.9 Trunk release function .................................................................................................................... 18

5.5.10 Two level - Door unlocking, when disarming ................................................................................ 18

5.5.11 Two steps disarming ...................................................................................................................... 18

5.6 ELECTRIC WINDOWS CLOSING WHEN ARMING .......................................................................................... 18

5.7 REVERSE CAR MOVING WARNING ......................................................................................................... 18

5.8 DOOR OPENED WARNING ................................................................................................................... 18

5.9 AUTOARMING .................................................................................................................................. 19

5.10 PASSIVE ARMING/WARNING AT PASSIVE ARMING/TEMPORARY DISABLE OF PASSIVE ARMING ............................. 19

5.11 REMOTE CONTROLLED DOORS LOCK/UNLOCK AND/OR WHEN SWITCHING ON/OFF THE ENGINE ........................ 19

5.12 DUAL MODE ................................................................................................................................. 19

5.13 ALARM MEMORY INDICATION .............................................................................................................. 19

5.14 BYPASSED FAULTED INPUTS INDICATION .............................................................................................. 20

5.15 ANTISCANNING/ANTIGRABBING ......................................................................................................... 20

5.16 NON-VOLATILE MEMORY FOR SYSTEM STATES ....................................................................................... 20

5.17 ALARM SITUATIONS WHEN THE SYSTEM IS ARMED ................................................................................. 20

5.18 COMFORT FUNCTION ...................................................................................................................... 21

5.19 DOOR CONTACTS DELAY, WHEN ARMING .............................................................................................. 21

CHAPTER VI: TESTING/ADJUSTMENTS ............................................................................................. 21

6.1 REAL CONDITIONS TESTING ............................................................................................................... 21

6.1.1 Testing the detection of the burglary attempts .............................................................................. 22

6.1.2 Testing the central door lock commands ........................................................................................ 22

Installation ManualAlcar®H51

CHAPTER I: INTRODUCTION

Alcar®H51 is an auto alarm, remote controlled with hopping code. This facility offers a

stronger protection than the fixed code systems, since the remote control is changing the

code at each button pressing.

It is a user-friendly modular system that can be configured in a very complex way. The doors are

protected by pin-switches, apart from the trunk and the hood. The alarm assures the engine

killing. The command from the shock sensor (included in the basic kit) will pre-warn for weak

shocks. For strong shocks or repeated weak shocks the alarm will trigger in a specific way.

The ALCAR®H51 range has the following versions:

-ALCAR®H51 - ALCAR®H51  minimal kit,

-ALCAR®H51U- ALCAR®H51 + ultrasonic sensor incorporated;

-ALCAR®H51DL - ALCAR®H51 + central door lock module incorporated;

-ALCAR®H51P - ALCAR®H51 + auto-pager module incorporated;

- Any combination of the upper options (ex: ALCAR®H51UDLP- maximal configuration, with

ultrasonic sensor, with central door lock module and auto-pager module).

Supplementary external sensors can be connected, such as one-zone or two-zone microwave

sensor or ultrasonic sensor.

This way, the system assures the protection of the interior of the car and/or can warn when

someone gets close to the car.

NOTES:

1) In this manual ALCAR®H51 will be referred as the whole range of auto alarms of this

kind, meaning that such functions are optional for the various constructive versions;

2) In this manual the two buttons remote control is referred (button 1) and (button 2). If the

remote control has 4 buttons, then the first two only will be used for operating the car alarm. The

other two can be used for subsequent developments (ex: for garage doors command, for

operating a burglary alarm system etc).

CHAPTER II: THE KIT

In the box you will find the following:

1. Central unit 2. Remote controls (2 pcs.)

3. Pin-switch (2 pcs.) 4. Mounting cables (3 sets)

5. Warning decal (2 pcs) 6. Spare fuses (10A, 2A)

7. Shock sensor + cable 8. Engine killer relay

9. Ultrasonic microphones 10. Valet switch

11. State LED

sensors stabilization period) the shock sensor and/or the external supplementary sensor are

active. Check the fact that the system warns optical-acoustical by 3 short signals. Check also that

the power supply of the bypassed sensorswas disconnected on that specific arming period

(sensors LED is off and the alarm system does not respond when the sensor is tested).

6.1.1 Testing the detection of the burglary attempts

With the system armed simulate burglary attempts in all the possible ways:

1) Put the key in contact and try starting the engine; the relay contacts should open (the engine

should not start), and the system should trigger the alarm (by siren, flashing lights and optionally by

pager) for 30s (this is the alarm for engine starting attempt).

2) Open and close one by one all the doors, the hood and the trunk; the system should trigger the

alarm (by siren, flashing lights and optionally by pager) for 30s.

3) Open a door and leave it opened; the system should trigger the alarm (by siren, flashing lights

and optionally by pager) for 30s, three times subsequently. After that the doors input will be

bypassed the other functions of the system remaining active. If the door is closed eventually, the

input should become active again.

4) After passing the sensors stabilization period (20s after arming), hit the car slightly; the system

should prewarn (for weak shocks). After repeated shocks within 5s, the system should trigger the

alarm (by siren, flashing lights and optionally by pager) intermittently 2s ON, 1s OFF, for 15s

(repeated shocks alarm).

5) After the stabilization period passed (20s after arming command), hit in astrong manner the car;

the system should trigger the alarm (by siren, flashing lights and optionally by pager) intermittently

2s ON, 1s OFF, for 15s (strong shocks alarm).

6) If the system is provided with ultrasonic sensor and the input for the supplementary sensor is

programmed properly, then, aftyer the sensors stabilization period (20s after arming), by leaving the

window opened, introduce the arm inside, through the window; the system should trigger the alarm

(by siren, flashing lights and optionally by pager) for 30s (alarm for violating the interior of the car).

7) If the system is provided with proximity sensor (microwave sensor), and the input for the

supplementary sensor is programmed properly, then, after sensors stabilization period (20s after

arming), when approaching the car, within sensors range, the system should emit one signal at

every detection, according to the value of the parameter 11 (warning for approaching the car).

6.1.2 Testing the central door lock commands

If the car is provided with central door lock check if:

a) Doors are locked when arming the system.

b) Doors are unlocked when disarming the system (if parameter 6 is active).

c) Doors are unlocked when turning off the engine (if parameter 7 is active).

d) Doors are locked when turning on the engine (if parameter 8 is active).

e) Doors are not locked when the system is passive arming, after 30s after turning off the engine

and closing the last door (if parameter 4 passive arming is active).

Installation ManualAlcar®H51

CHAPTER III: GENERAL FEATURES

1. Arming/disarming by remote controls (confirmation by siren chirps and flashing)

2. Arming/disarming by remote controls (confirmation by flashing only)

3. Passive arming (programmable) / Warning at passive arming

4. Arming with silent alarm (no siren, programmable)

5. Two steps disarming

6. Protection against accidental disarming (auto-arming)

7. Doors protection

8. Trunk and hood protection, apart from the door input

9. Pre-warning for weak shocks, alarm for strong shocks or repeated weak shocks

10. External sensors connection possibility (microwave, simple or dual and/or ultrasonic)

11. Car find

12. Panic

13. Reverse car moving warning (programmable)

14. Warning for door open (programmable)

15. Warning when approaching the car (optional, programmable)

16. Warning when arming with the lights turned on

17. Engine killing

18. Option for deactivating any sensor by remote control

19. Defective sensors bypassing when arming

20. Separate power supply for each sensor input

21. Low consumption (disconnecting the bypassed sensors power supply)

22. Remote alarm notify (optionally, by pager)

23. Non-volatile memory for system parameters and remote controls

24. System state keeping when disconnecting and reconnecting the power supply

25. Learning/clearing remote controls procedure

26. System parameters programming procedure

27. Learnt remote controls number notification

28. Anti-car-jacking procedure (programmable)

29. Anti-scanning / Anti-grabbing

30. Service mode / Emergency disarming by valet switch

31. Central door lock module incorporated

32. Remote controlled doors lock/unlock and/or when switching ON/OFF the engine (optionally,

programmable)

33. Electric windows closing when arming the system (optionally)

34. Trunk release by remote control (optionally)

35. Events Log on the state LED (alarm memory indications)

36. Bypassed defective sensors indicated on the state LED

37. Back-up battery siren (optionally)

Notes:

a) If the system is armed with silent alarm function (no siren), the alarm state will be notified by

pager and flashing lights or only by pager, according to the value of parameter 9 (see 5.2., system

parameters);

b) Any alarm state can be stopped by pressing shortly (0.5s) the button 1 or 2, without disarming

the system. For disarming the system when the alarm is in progress, press button 1 twice (once to

stop the alarm and second time to disarm the system).

5.18 COMFORT FUNCTION

The Comfort function is available for some newer models of cars. At these cars, when twisting the

key the doors will lock. If maintaining the key twisted for more than 5s then the windows will roll up.

The Comfort function provides when arming a longer trigger (10s) on the lock doors output, no

matter of parameter 1 value.

Caution!

Do not run this wire directly to the door lock actuator, but to the command wires existing on the car!

For details please call the manufacturer!

5.19 DOOR CONTACTS DELAY, WHEN ARMING

This function is only used for the cars which maintain ON the dome lamp, a certain time, after the

last door is closed. In this case, the parameter 11  Door contacts delay, when arming will be

programmed actively. Then, the state of the door pin switches is only tested after the delay time

estabilished by parameter 12.

If after delay time, the alarm system detects at least a door opened, it notifies by 3 opto-acoustic

signals and bypasses the respective input. If afterwards all the doors will be closed, the respective

input becomes actively again. The signal for the door inputs will be taken from the (+) terminal of the

dome lamp.

CHAPTER VI: TESTING/ADJUSTMENTS

6.1 REAL CONDITIONS TESTING

1) Stop the engine, close the doors, the hood and the trunk. Arm and disarm the system with and

without acoustical confirmation like. The state LEDwill indicate as follows:

- blinking slow  system is armed;

- off  system is disarmed;

- on  system is in alarm;

- blinking fast  system is within the 30s after disarm command, when it is waiting for a

door to be opened (see 5.9).

- system is within 30s after the engine was turned off and the last door was closed and it is

counting the time for passive arming (see 5.10).

- short blinks  after disarming and closing the last door the system indicates the alarm memory or

the faulty inputs type; while in programming mode the system indicates the parameters values.

2) Arm the system and bypass manually by remote control the sensors according to 5.5.5. Check

the fact that power supply of the bypassed sensor was disabled while armed (sensors LED is off

and the alarm system does not respond when the sensor is tested).

3) Arm the system and simulate various situations so, after 20s from arming (at the end of the

Installation ManualAlcar®H51

CHAPTER IV INSTALLATION

During this section there are presented the location, the mounting and the electrical connections

necessary for the alarm system installation.

This alarm system can only be installed on cars that have the negative pole of the

battery connected to the chassis!

NOTE: Read carefully this manual before starting the installation. If you are not sure you are able

to do it by yourself, call a specialist!

4.1 SIREN MOUNTING

The siren will be mounted in the hood compartment, away from high temperature sources and

humidity. The chosen place should not be obstructed in order not to attenuate the siren sound.

Also, the place should be as inaccessible as possible to prevent the tamper.

Fasten the siren up side down by using screws.

4.2 PIN SWITCH MOUNTING AT HOOD AND TRUNK

Choose the mounting place such as the pin-switches should be able to move about 6mm. in the

closed position of the hood and trunk.

4.3 CENTRAL UNIT MOUNTING

Choose a horizontal place, hidden, preferably under dashboard. Fasten the central unit with screws

on the car chassis.

4.4 CONNECTIONS

There are 8 connectors on the central unit (A, B, C, D, E, F, G, H). The connectors correspond

respectively to the cable sets A, B, C, D, F, G, H.

The connections will be made according to the general mounting diagram (D).

4.4.1 Cable set A

Commands the central door lock system.

The timing for commanding the central door lock system can be set to 0,8s. for electric door

lock and 4s. respectively for pneumatic door lock. The selection is made through parameter

1-Timing for door lock.

Before connecting the cable A and setting parameter 1, one should determine the type of central

door lock existent on the car. A simple way is to try and lock the car doors by locking the right-front

door, by locking this door:

1) the doors are instantly closing, then the car is provided with electric door lock system

2) the doors are closing in an interval of few seconds, then the car is provided with pneumatic

door lock system

4.4.2 Cable set B

B1 (black)

System GND. Connect to (-) pole of the battery.

Note: In order to improve the noise immunity it is indicated that the power supply wires (B2-red and

B1-black) to be connected directly to the batterys poles.

5.14 BYPASSED FAULTED INPUTS INDICATION

If when arming the system has bypassed any input (doors, hood, sensors) within 20s after arming,

then whn disarming, after opening any door the hood or trunk, the system will indicate by the state

LED, the type of input as follows:

1 blink - shock sensor

2 blinks - ultrasonic sensor

3 blinks - contact key (attempt to start the engine)

4 blinks - door contacts

5 blinks- hood, trunk contacts

After starting the engine the faulted inputs memory will be reset and the LED will turn off.

The alarm memory is prioritary towards the faulty sensors indication. So, the LED will indicate the

faulty inputs bypassed only if there was no alarm.

5.15 ANTISCANNING/ANTIGRABBING

ALCAR®-51, is protected for scanning and grabbing.

5.16 NON-VOLATILE MEMORY FOR SYSTEM STATES

When the system is powered again (after the power was OFF), it enters the state which was

previously (armed, disarmed, service, anti-carjacking). If the system was in the arming mode when

the power was OFF, then at the power restoring the sensors state and the event memory will be

restored and the system will tripp a panic alarm.

Note: There is a certain situation namely: if parameter 11  Door contacts delay when arming is

enabled, parameter 12  Door contacts delay duration is 5s, a door is opened when arming and

the power is breaked before the fifth second from the arming, then when rearming, if the door is still

open, the system enters a door alarm .

5.17 ALARM SITUATIONS WHEN THE SYSTEM IS ARMED

1. When opening a door, the hood or the trunk  alarm by siren, flashing lights and optionally

by pager, for 30s;

If a door is left opened in a burglary attempt, the system triggers the alarm (siren, flashing lights and

pager), for three times of 30s each. After the 3 x 30s alarm sequence the doors input is bypassed

and the other functions of the system are still active. This is executed even if the alarm is stopped

by remote control.

If subsequently the related door is closed, the doors input becomes active again.

2. When trying to start the engine with the key  alarm by siren, flashing lights and optionally

by pager, for 30s;

3. When the car receives a weak shock optical-acoustical warning for 1s.

4. When the car receives repeated weak shocks within 5s or a strong shock  alarm by

siren, flashing lights and optionally by pager, for 15s, intermittently 2s ON, 1s OFF;

5. When violating the interior of the car, if the supplementary input is set for ultrasonic

sensor alarm by siren, flashing lights and optionally by pager, for 30s;

6. When approaching the car, if the supplementary input is set for proximity sensor 

programmable warning (see parameter 10).

Installation ManualAlcar®H51

B2 (red)

General power supply of the system. Check the 2A fuse and connect to (+) pole of the battery

together with the pink wire (B5).

B3 (purple)

Open collector PNP output, maximum 1A (positive trigger).

The output state is related to the Parameter 0 value in the following way:

Parameter 0 = 1 Parameter 0 = 2

In normal state GND +12V

When active +12V GND

Generally there are 3 types of siren, which are:

1) Normal siren, which provides two wires (+) and (GND).

Parameter 0 should be set as 1 and the siren should be connected as follows:

- (+) to B3;

- (GND) to GND;

2) Back-up siren, with three wires: (+), (GND) and (COMMAND). On the (COMMAND) wire

there should be permanently (+), while the siren is powered ON. Thus, when removing (+) from the

(COMMAND) wire, the siren should sound.

Parameter 0 should be set as 2 and the siren should be connected as follows:

- (+) to (+12V);

- (GND) to GND;

- (COMMAND) to B3.

3) Back-up siren, with four wires: (+), (GND), (NEG.TRIG) and (POSITIVE TRIG). While the siren

is powered ON, it will sound either when (NEG.TRIG) is connected to GND or when (POSITIVE TRIG)

is connected to (+12V). On the (COMMAND) wire there should be permanently (+),Thus, when

removing (+) from the (COMMAND) wire, the siren will sound.

Parameter 0 might be set either 1 or 2 and the siren should be connected as follows:

- (+)to (+12V);

- (GND) to GND;

- (POSITIVE TRIG) to B3 if Param. 0 is 1;

- (NEG.TRIG) to B3 if Param. 0 is 2;

B4, B6 (gray)

Connect to (+) pole of the signaling lamps left and right respectively.

B5 (pink)

Power supply for the signaling lamps. Check the 10A fuse and connect to (+) pole of the car battery

together with the red wire (B2).

4.4.3 Cable set C

C1 (orange)  open collector, negative trigger, and maximum 500mA load output for window

closing when arming the system. The output is active all the time while the system armed. It

commands an optional module type RB-06.

5.9 AUTOARMING

To assure the protection against accidental disarming of the system, if after disarming command,

within 30s there is no door opened or the engine is not turned on, the alarm system will arm

automatically.

This function is permanently active.

5.10 PASSIVE ARMING/WARNING AT PASSIVE ARMING/TEMPORARY DISABLE OF PASSIVE ARMING

If parameter 4 (passive arming- disabled by default) is set enabled, the system will arm passive

after 30s from turning off the engine and the last door closed.

After closing the last door, the system will notify by an optical-acoustical signal (default) or just

optical, for silent disarming.

If the parameter 5 is enabled, the passive arming can temporary disable by opening and closing

twice a door within 5s.

The passive arming is useful since it prevents forgetting the car disarmed. The passive arming is

made without locking doors.

5.11 REMOTE CONTROLLED DOORS LOCK/UNLOCK AND/OR WHEN SWITCHING ON/OFF THE

ENGINE

If the car is provided with central door lock the system will lock the doors when arming and unlock

the doors when disarming (according to the value of parameter 6).

Also, the system can unlock the doors when turning the engine off (see parameter 7) or lock the

doors when turning the engine on (see parameter 8).

5.12 DUAL MODE

This referrs to the possibility of triggering the alarm by the ultrasonic sensor only if within 15s are

activated at least two sensor types (ultrasonic + proximity or ultrasonic + shock).

That means that if parameter 14 (Dual mode) is enabled the alarm triggering by the ultrasonic sensor

can only be done if the interior detection was preceded or succeeded within 15s by another sensor

triggering (shock or proximity).

It is strongly recommended to use dual mode only when the system is provided with all sensors

type (shock, ultrasonic and proximity). This mode is useful under these circumstances because it

prevents false alarms. Enabling/disabling this mode is made by enabling/disabling parameter 14.

It is not recommended to use the dual mode if the system is not provided with proximity sensor.

5.13 ALARM MEMORY INDICATION

If while armed at least an alarm was recorded, after disarming and opening the door, the system will

indicate by the state LED the type of the sensor that triggered the alarm, as follows:

1 blink - shock sensor

2 blinks - ultrasonic sensor

3 blinks - contact key (attempt to start the engine)

4 blinks - door contacts

5 blinks- hood, trunk contacts

After starting the engine the alarm memory will be reset and the LED will turn off.

Installation ManualAlcar®H51

C2 (brown)  input for checking the engine state ON/OFF. Connect to ON wire (coil) of the

contact key switch.

In order to find this wire:

- Switch the key in contact until the lights in the dashboard turn on;

- Search on the contact key hub the wire on which the voltage is +12V; In this position and in

START position too, the voltage on this wire should remain +12V.

NOTE!

There is another wire, marked sometimes ACCESSORIES, used to power up some accessories

(radio, cooler etc.), which provides +12V with the key in hub and the engine turned on. However, in

START position the +12V voltage is not provided anymore. Do not confuse with this one!

C3 (green + white)  negative triggered input, for trunk and hood state closed/opened.

C4 (green)  negative triggered input, for doors state closed/opened.

Note:

For C3 and C4 negative triggered inputs is important the doors switches type!

One can check by using a voltmeter the switching type of the doors switches, this way:

1. Open a door and locate the door switch.

2. Connect the voltmeter between GND and the main contact of the switch.

3. If the inside lamp turns on and the voltmeter indicates 0V then the switching is negative. In

this case the doors switches will be connected directly to C4, in parallel, according to general

mounting diagram (D)

4. If the voltmeter indicates 12V, then the switching is positive. In this case the connection will

be made by means of a relay according to diagram C.

Relay NO

+12V

Lamp

Door

switch

Relay for positive trigger

doors switches

C4/GREEN

Input for negative

trigger switches

C5 (purple)  Input from (+) pole of the position lights (for warning when arming with the position

lights turned on).

C6 (white)  Input from (+) pole of the backlights (for reverse moving warning function).

C7 (yellow) - open collector, negative trigger and maximum 500mA load output for command of the

external engine killer relay.

In order to use anti-carjacking function, the engine killing will be made on the injection pump, fuel

pump, coil etc.

b) From this point the system waits 30s, then it returns to the upper state 3, resuming the warning

signals. If the button 2 of the remote control is pressed again, with contact key in OFF position only,

the system leaves the anti-carjacking mode. It emits 1 acoustic signal for 1s, followed by 2 optical

signals and it enters the disarming mode.

c) If the button 2 is not pressed and the system reaches the state 4, then the exit procedure should

be executed again from point a).

Note:

After entering the anti-carjacking procedure, if the alarm power supply is disconnected, when the

system is powered up again it will enter anti-carjacking state.

5.5.9 Trunk release function

If an interface module RB-04 is connected, for trunk release, it will be actionated pressing long, for

about 2s, button 2 of the remote control.

The function is active only when the system is disarmed and the engine turned off.

5.5.10 Two level - Door unlocking, when disarming

For two level  door unlocking when disarming the system should be provided with the diode D19

on board. This way, the parameter 6 (unlocking doors when disarming) should be inactivated.

In this configuration the system doesnt unlock the doors when disarming while pressing the button

1. For unlocking the doors by remote the button 2 must be pressed more than 2 seconds. Once this

option enabled the trunk release function is not anymore available!

5.5.11 Two steps disarming

Any alarm state can be stoped pressing the button 1 or 2 for short time (aprox. 2s) without the

system to be disarmed. For system disarming when the alarm is triggered, the button 1 should be

pressed twice (once for alarm stoping and seconnd for disarming).

5.6 ELECTRIC WINDOWS CLOSING WHEN ARMING

When arming the system, if there is connected an optional module RB-06, then the windows will

close automatically.

5.7 REVERSE CAR MOVING WARNING

When moving backwards the system warns by optical-acoustical signals (or just optical if the

system was disarmed silent), according to the setting of parameter 2 (see system parameters

programming). This parameter is enabled by default for optical-acoustic notification.

Also, when disarming silent, the reverse car warning is optical only.

5.8 DOOR OPENED WARNING

If, after the engine is turned on, one of the doors remains opened for more than 15s, the system will

warn by 6 optical-acoustical signals, or just optical, according to the value of parameter 3 (see

system parameters programming). This parameter is set by default for optical-acoustical warn-

ing.

If the disarming was silent, the door-opened warning is optically only.

If a door is opened while riding, the system wil emit the same warning signals, after 15s.

Also, the same warning signals will be emitted when the hood or the trunk are opened.

Installation ManualAlcar®H51

Connect according to diagrams A or B.

When connecting the relay on starter the four wires will be connected as follows:

-Yellow wire of the relay to the yellow wire C7 of the central unit;

- Search on the contact key hub the command wire for engine starter (usually a large section

one), cut and connect serial with the relay contacts (the blue and the orange wires of the

relay);

- Red wire of the relay will be connected to C2 (brown) wire of the central unit to ON, on contact

key hub;

Note:

To find the starter command wire on contact key hub:

a) Switch the key in contact until the starter is triggered;

b) Search on the hub the wire that provides +12V in this position only! In any other position

of the key, this wire should provide no voltage.

C7/YELLOW

Engine killer

command circuit

Engine killer

external relay

YELLOW

ORANGE

BLUE

Engine

contact

hub

Engine starter

Starter

power up

Ignition

RED 85

87a

Engine starter killer

C7/YELLOW

Engine killer

command circuit

Engine killer

external relay

YELLOW

ORANGE

BLUE

Engine

contact

hub

- Fuel

pump

- Injection

- Induction

coil

Ignition

RED 85

87a

Engine killing on

other devices

C8 (blue) - open collector, negative trigger and maximum 500mA load output for remote trunk

release. This wire will be connect to an optional module RB-04.

4.4.4 Dconnector

It is the connector for the state LED. It is recommended to mount the LED in a visible place (usually

on the dashboard), in order to notify the existence of the alarm system and to discourage an

eventual burglary attempt.

4.4.5 Econnector

The shock sensor ES-21K will be mounted on this connector. It is recommended to locate the shock

in the center of the car to detect the shocks from any part of the car. The sensor sensitivity is

adjustable. The power up of the sensor is cut off when the sensor is bypassed (by remote control

or when it if found faulted when arming).

4.4.6 Fconnector

An external optional sensor can be connected on this connector (microwave or ultrasonic sensor).

This connector is provided with 4 (optionally 5) connection pins:

NOTE!

If the both buttons of the remote are pressed simultaneously during the first 5s after arming, the

silent alarm function will be enabled (during respective arming period the siren will be disabled).

The silent alarm function enabling will be confirmed by 2 optical-acoustic signals (or optical signals,

depending on arming mode).

5.5.7 Signalling the remote controls number

The hopping code remote controls of ALCAR®-H51, are learnt by the central unit through the

procedure described in chapter 5.1  Learning/clearing remote controls. The remote controls

number, recorded in central units memory (up to 4), can be notified by a simple short press of

button 2 while in disarmed mode. The system answers by a number of optical-acoustical

signals (or optical only if the system was disarmed silent) equal to the remote controls number.

Note!

1) While disarmed, when the engine is turned off, pressing long (more than 2s.) the button 2

will activate the trunk release output;

2) While disarmed, when the engine is turned on, if parameter 13 (anti-car jacking) is enabled,

by pressing long (more than 2s.) the button 2 will enter the anti-car jacking mode.

5.5.8 Anti-carjacking mode

The function is necessary in the case when the burglar threats the owner and takes the car in its

presence, with the key in contact. Once the function is triggered, the car will stop after 1min. and

will enter the anti-carjacking alarm mode..

The function should be enabled when setting the system parameters (see 5.2, parameter 13), and

the external 40A/12V relay should be connected to cut the induction coil the injection pump etc. The

function doesnt work if the external relay cuts the engine starter!

Note!

The car owner should have another remote control apart from the keys!

To trigger anti-carjacking procedure presslong (about 2s) button 2, when the engine is

turned on. The system will enter the procedure and will confirm by flashing lights for 2s. After the

confirmation the alarm passes the following states:

1) During first 14s the alarm does not respond to any remote control command;

2) In the following 16s one can leave the anti-carjacking following the exit procedure;

3) In the following 30s the alarm emitts short siren sounds and optical signals, warning that the

engine will turn off. One can leave the anti-carjacking following the exit procedure.

4) After expiry of the 60s, the alarm enters the anti-carjacking alarm mode, in which the engine

stops, the sirens sounds continuously and the flashing lights are on until the battery is completely

discharged. One can leave the anti-carjacking following the exit procedure.

To exit anti-carjacking mode you must follow the procedure bellow:

a) In any state 2, 3 or 4 previously enumerated press the button 2 of remote control. The warning or

the alarm sounds will be stoped. The engine killing will be stoped (if the system was in state 4) and

the system will emit 1 optical signal for 2s, followed by 2 optical-acoustic signals.

Installation ManualAlcar®H51

1) GND;

2) Warning input (when detecting movement around the car);

3) Alarm input (when detecting movement inside the car);

4) Commanded power up for the optional microwave sensor;

5) Commanded power up for the optional ultrasonic sensor;

The connector has 4 pins for standard configuration. Optional, when an internal sensor is mounted

besides the built-in sensor, the central unit has to be properly equippated (to assure a separate

power supply for ultrasonic sensor / sensors and microwave sensor).

These external sensors should provide a negative trigger output when activated.

The central unit commands separately the sensors power supplies. They are interrupted when

bypassing the sensors (by remote control or when it if found faulted when arming).

The external sensors sensitivity is adjustable.

NOTE: For all sensors, adjusting the trimmer to the left or to the right the sensitivity decreases or

increases respectively.

4.4.7 G Connector

This is the connector for the push-button (valet switch). This switch it is used for:

- Remote controls learning;

- Service mode / emergency disarming;

- System parameters programming.

NOTE!

The push-button should be mounted in a hidden place known by the owner only!

4.4.8 H connector

This one connects the ultrasonic sensor microphones.

4.4.9 Pager connecting

Pager connecting is optional. The related module, by default is not included in the basic kit.

CHAPTER V: SYSTEM OPERATING

5.1 LEARNING / CLEARING REMOTE CONTROLS

The central unit already knows the two remote controls provided with the basic kit. Up to four

remote controls can be learnt by the central unit.

In order to learn or clear from memory remote controls, one should do the following:

1) Disarm the system;

2) Switch the engine contact key twice, such as the key switches subsequently

between: ON, OFF, ON, OFF;

3) Press the push-button three times within 15s. A success-

ful enter in learn/clear mode will be confirmed by two optical and acoustical signals;

4) For learning, press one of the remote controls buttons within 15s. after pressing the push-

by an optical-acoustic or optical signal (depending on arming mode) and advances to the next

sensor.

If the button 2 of the remote control is pressed, the system doest bypass the sensor, but it

advances to the next sensor and confirms by optical-acoustic or optical signal.

Sensors bypass is only available for that respective arming period. When disarming the system the

bypass is disabled.

Example: If one wishes to bypass the shock sensor only it will proceed as follows:

1. During the first 5s after the arming command press button 2 to advance at the shock sensor

without bypassing the proximity sensor. The system confirms by an optical-acoustical signal (or

just optical if the arming was silent).

2. Press button 1 to bypass the shock sensor. The system confirms by an optical-acoustical

signal (or just optical if the arming was silent).

3. Press button 2 for not bypassing the ultrasonic sensor. If the button 2 is pressed the system

confirms by an optical-acoustical signal (or just optical if the arming was silent).

5.5.4 Arming with silent alarm

If the owner dos not want the theft to be warned, then the system can be armed with silent alarm

(the siren is disabled). The using of this function is needed when the system has a pager. The alarm

state will be notified on page and flashing lights only, according to the value of parameter 9 (see 5.2.

system parameters).

The silent alarm function can only be activated within the first 5s after the arming command,

by simultaneously pressing both remote control buttons. The function is active during that

specific arming period only. The function enabling is confirmed by 2 optical-acoustic signals (or only

optical signals for silent arming). When disarming the system, the function is disabled.

5.5.5 Car finding

In order to locate the car in a full parking area, press shortly (0.5s) the button 2. Five optical and

acoustical signals will be provided. The signals will be:

- short if no alarm was reported meanwhile;

- long if there was an alarm since the system was armed

This function is active with the system armed only.

NOTE!

The car finding function is not active during the reserved 5s after the arming command.

If the button 2 is pressed during the first 5s after arming this command will be interpreteted

according to sensors disabling by remote control procedure.

5.5.6 Panic

In case of emergency, pressing shortly (0.5s) and simultaneously the two buttons of a

remote control can trigger the alarm. The siren will sound continuously, the pager will emit the

alarm signal (if there is provided a pager, which is optional) and the flashing lights will flash for

three minutes.

This function is used to discourage a potential burglar, and to draw the attention towards the

vehicle.

The function is enabled no matter of the systems state (armed/disarmed), except the first 5s after

arming and can be stopped during the thre minutes by pressing shortly any of the buttons.

Installation ManualAlcar®H51

button; a successful learning will be confirmed by an optical-acoustical signal;

5) To clear all the remote controls from the central unit memory press simultaneously both

remote control buttons of a known remote control. The clearing of all remote controls at

once will be confirmed by three optical-acoustical signals;

6) To leave the learn mode switch the contact key to ON position. Also, leaving the learn

mode will automatically be made after 15s. in which there is no remote control button pressed.

Notes:

a) The remote controls record in the central unit memory is made cyclically from location 1 to location

4, respecting FIFO principle (First In First Out). So, if the memory is full, the oldest remote control will

be erased when learning a new one.

b) By simultaneously pressing bot buttons of a new remote control, while in learning mode, then the

system will learn that remote control. (It will not be executed the operation of clearing all the remote

controls).

c) If the same remote control is learnt twice, it will be confirmed second time too, but it will not fill a

second memory location.

1) In the case a remote control was stolen or lost a clearing of all the remote

controls at once operation will be effected. Then, the remained remote controls and the new ones

will be learnt

2) In the case all remote control were stolen or lost a new remote control learning

operation will be effected. Then a clearing of all the remote controls at once operation will be

effected followed by a learning operation for the new remote controls.

5.2 SYSTEM PARAMETERS PROGRAMMING

Table I: SYSTEM PARAMETERS (default values in bold)

No. Parameter description

Optical-acoustical signal

1 signal 2 signals

0 Siren type Po sitive triggered Negative triggered

1 Central door lock timing 0,8s (electrical) 4s (pneumatically)

2 Reverse car moving warning optical-acoustical Optical only

3 Warning for door open optical-acoustical Optical only

4 Passive arming enabled disabled

5 Temporarily disabling the passive arming enabled disabled

6 Unlock the doors when disarming enabled disabled

7 Unlock the doors when turning OFF the

engine

enabled disabled

8 Lock the doors when turning ON the

engine

enabled disabled

the remote controls is about 30m. The remote control is provided to 2 buttons, which will be referred

as 1 and 2.

The remote control is also provided with a LED that turns on when pressing any of the buttons. If

one note decreasing of the light intensity of the LED then the battery should be replaced.

Combining the two buttons it results a lot of functions that will be explained in the followings.

5.5.1 Arming/disarming with confirmation by siren chirps and flashing lights

System arming/disarming is simply made by shortly pressing (about 0,5s.) button 1. The

system toggles to one state or another according to the current state.

The arming confirmation is made both optically and acoustically, by one signal, and the

disarming confirmation will be made by two optical-acoustical signals (on flashing lights and

siren).

When arming:

1) If the system detects the hood, the trunk or a door opened, it warns by three optical-acoustical

signals and bypasses the respective inputs during arming. If afterwards the respective inputs are

restored (closing the hood, trunk or doors) they become active.

After sensors stabilization delay (20s. after arming), by opening again any door, the hood or the

trunk the alarm will be triggered.

2) If the system detects the position lights turned on, it will warn by a signal similar to the proximity

approach warning, according to the value of parameter 10.

When disarming, if the alarm has been triggered while armed, four optical-acoustical signals will

be emitted.

Note:

1) After arming the first 5s. are reserved for supplemental commands such as:

2) manual sensors bypass by remote control (the proximity sensor, the shock sensor and the

ultrasonic sensor);

3) silent alarm enabling (the siren is disabled);

4) System disarming can only be made after the 5s after arming command;

5) If the parameter 11 - Door contacts delay when arming is enabled, then the doors pin-

switches are tested only after delay duration estabilished by parameter 12. If, the delay duration is

over and the system detects at least one opened door, it will warn by three optical-acoustical

signals and it will bypass the respective input during arming.

6) If afterwards all the doors are closed, the respective input becomes active again, after

sensors stabilization delay (20s after arming).

5.5.2 Arming/disarming silent

When no acoustical confirmation is needed, press the button 1 for about 2s instead of the short

press described before (0.5s). All the signals will become silent, meaning that the optical confirma-

tion only will remain active for respective arming/disarming period (warning for reverse car moving,

for door open, for arming with position lights turned ON, for silent siren, for sensors bypassing by

remote control, for doors, hood and trunck bypassing, for faulted sensors disabling when arming).

5.5.3 Remote controlled bypassing the sensors

Remote controlled bypassing the sensors can only be made during the first 5s after the

arming command. The bypass order is: proximity sensor -> shock sensor -> ultrasonic

sensor.

If the button 1 of the remote control is pressed, the system bypasses respective sensor, confirms

Andere Handbücher für Alcar H51

Inhaltsverzeichnis

Andere ROEL Sicherheitssystem Handbücher

ROEL

ROEL Cerber c41 Montageanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung