Roger Technology CTRL Bedienungsanleitung
Quick Start CTRL MASTER/SLAVE
Rev01 17/08/2020
ROGER TECHNOLOGY
Via S. Botticelli 8 • 31021 Bonisiolo di Mogliano Veneto (TV) • ITALIA
P.IVA 01612340263 • Tel. +39 041.5937023 • Fax. +39 041.5937024
info@rogertechnology.com • www.rogertechnology.com
APower supply H07RN-F 3x1,5 mm2 double insulated cable
1Photocell - Receiver 5 x 0.5 mm2double insulated cable (max. 20 m)
2Photocell - Transmitter 3 x 0.5 mm2double insulated cable (max. 20 m)
3Selector / Keypad 3 x 0.5 mm2cable
1. Typical installation (purely for information)
CTRL is the range of 36V DC digital controllers installed with the barrier applications.
EN
1
2
2
3
A
1
A
F4ES-F4S
Series
R85/60
1 2 3 2345
+- +-
TX RX
1
COM
NO
CS/STD
TRASFORMATORE
PRIMARIO
MONOFASE
SECONDARIO
CEI 61558-2-6
0 19 0 26
F1
F2
F3
PROG TEST
+
-
BATTERY (+)
RECEIVER CARD
BATTERY CHARGER
SEC2
ENC2
ENC1
LOCKS
LED LIGHT
SEC1
BATTERY (-)
123456
Y
X
M
Z
78
COM
COM
+24V
+ES
+LAM
COM
COM
LNA
LNB
+SC
10 11 12 13 14 15 16 17 18 19 20
+LUCI
ST
COM
COS
FT
COM
ANT
21 22 23 24 25
COM
PED
PP
CH
AP
28 29 30 31 32
ORO
33
COM
3426 27
9
F4
N
L
POWER SUPPLY
230Vac / 115Vac
BATTERIES
2 x 12V 4,5Ah
BIONIK BIONIK 4HP/6 BIONIK 8
3. Display: functions and settings
Accessories illustrated are indicative only
PROG TEST
+
-
Back
Programming Check error alarms
PARAMETER PARAMETER
VALUE
Increase value
Decrease value
Next
PROG TEST
+
-
2. Electrical connections
4. Before starting ...
a) IMPORTANT: Select the length of the boom with the parameter A1.
It is very important that this parameter is selected correctly. An incorrect setting may cause severe damage or injury.
AG/004
KB/004
BI/004HP up to 3 m
BI/004 up to 3 m
AG/004
KB/004
BI/004HP from 3 m to 4,5 m BI/004 from 3 m to 4 m
AG/006
KB/006
BI/006 from 4,5 m to 6 m BI/008 up to 8 m
b) Check the spring balance setting and the mechanical stop setting.
See the installation manual for the barrier.
c) With both control units not powered (and with battery disconnected,
if present), make the bus connections on the MASTER and SLAVE
control units
d) Enable RS485 serial communication (MASTER): A011
e) Enable RS485 serial communication (SLAVE): A010
45° >45°
<45°
RECEIVER CARD
ENC2
ENC1
LOCKS
LED LIGHT
COM
COM
+24V
+ES
+LAM
COM
COM
LNA
LNB
+SC
10 11 12 13 14 15 16 17 18 19 20
+LUCI
ST
COM
COS
FT
COM
ANT
21 22 23 24 25
COM
PED
PP
CH
AP
28 29 30 31 32
ORO
33
COM
3426 27
Costa di sicurezza MASTER / MASTER Safety edge
STOP (MASTER+SLAVE)
Antenna
RG58 max 10 m
Apertura parziale / Partial opening
Passo passo / Step by step
Chiusura / Closing
Apertura / Opening
Orologio / Timer
RX
TX
1 2 3 1 2 345
+- +-
RECEIVER CARD
ENC2
ENC1
LOCKS
LED LIGHT
COM
COM
+24V
+ES
+LAM
COM
COM
LNA
LNB
+SC
10 11 12 13 14 15 16 17 18 19 20
+LUCI
ST
COM
COS
FT
COM
ANT
21 22 23 24 25
COM
PED
PP
CH
AP
28 29 30 31 32
ORO
33
COM
3426 27
Costa di sicurezza SLAVE / SLAVE Safety ed
g
STOP (SLAVE)
MASTER
SLAVE
IMPOSTAZIONE DI FABBRICA
FACTORY SETTING
5. MASTER acquisition procedure
1. Check that the barrier boom is at 45°.
2. Press and hold PROG for 4 s.
3. APP- appears on the display.
4. Open the release cover.
5. PHAS appears.
6. Wait until the message PHAS flashes.
7. Close the release cover.
8. AUTO appears.
9. The barrier starts to open.
10. Once the barrier is open, the message AUTO flashes on the display after a few seconds and the barrier starts to close.
11. When the barrier is closed, the safety device symbols are displayed.
f) Select the position of the barrier in relation to the gate, using
parameter 1.
The factory setting of the parameter is with the barrier installed on
the right (101) and the boom opening/closure gate on the left
(seen from the inspection hatch side).
If the installation position is changed from the right to the left, the position of
the spring(s) must also be changed.
IMPORTANT! Lubricate the pivot points with lithium
based grease
6. Setting basic parameters
5. SLAVE acquisition procedure
1. Check that the barrier boom is at 45°.
2. Press and hold PROG for 4 s.
3. APP- appears on the display.
4. Open the release cover.
5. PHAS appears.
6. Wait until the message PHAS flashes.
7. Close the release cover.
8. AUTO appears.
9. The barrier starts to open.
10. Once the barrier is open, the message AUTO flashes on the display after a few seconds and the barrier starts to close.
11. When the barrier is closed, the safety device symbols are displayed.
AP P- PH A5
AU to
PROG
x4 s
OPENING OPEN CLOSING CLOSED
Yes
UNLOCK LOCK
2x360° 2x360°
PH
PH
A5
A5
AU
AU
to
to
45°
ONLY FOR BI/004 wait...
wait...
ONLY FOR BI/004
BIONIK 4HP, 6,
8, PC, PE
BIONIK 4HP, 6,
8, PC, PE
AP P- PH A5
AU to
PROG
x4 s
OPENING OPEN CLOSING CLOSED
Yes
UNLOCK LOCK
2x360° 2x360°
PH
PH
A5
A5
AU
AU
to
to
45°
ONLY FOR BI/004 wait...
wait...
ONLY FOR BI/004
BIONIK 4HP, 6,
8, PC, PE
BIONIK 4HP, 6,
8, PC, PE
The parameters concerning the functionality of the central unit are managed exclusively by the MASTER central unit which automatically passes them to the
SLAVE central unit. Only parameters A0,19, 31 and 3 must be set on the SLAVE control unit.
Obstacle detection function setting
Setting opening
start acceleration
Setting opening speed
Setting closure speed
Setting closure
start acceleration
Setting deceleration
during opening
Setting deceleration
during closure
Opening approach
distance setting
Closing approach
distance setting
7. Programming a NEW transmitter
8. Copying a transmitter
x5 s x3 s x1 s
AAA
A
B
OLD
P1
L1 L2
P2 P1
L1 L2
P2
ON
P1
L1 L2
P2
1 click
1. Press channel P1 (P2) of the receiver.
2. When LED L1 (L2) ashes 3 times (or 4 times
with rolling code function), press any button on
the transmitter.
3. If LED L1 (L2) remains steadily lit the transmitter
has been stored correctly.
1. Press buttons A and B on the NEW transmitter
simultaneously.
2. The LED ashes for 5 s.
3. Hold button (A) only on the NEW transmitter
you want to store.
4. The LED ashes 3 s.
5. Hold the previously stored transmitter as close
as possible to the NEW transmitter.
6. Press button (A) on the OLD transmitter.
7. The LED lights for 1 s to conrm that the copy
procedure was successful.
This document is a basic quick guide for the initial installation of a barrier.
For complete information concerning the control unit, the motor and the accessories mentioned in this quick guide, see the technical manuals available in the B2B area of the website
www.rogertechnology.it
9. Photocells grounding connection
Grounding connection negative terminal (COM) photocells series F4ES/F4S or other than Roger Technology
In case of malfunction, or failure to intervene in case of dimming, or continuous detection, or abnormal behaviour of the automation (gate, overhead door,
barrier, etc.), it is advisable to connect the negative terminal (COM) of the photocells to the grounding of the system.
PROG TEST
+
-
RECEIVER CARD
ENC2
ENC1
LOCKS
LED LIGHT
COM
+24V
+ES
+LAM
COM
COM
LNA
LNB
+SC
10 11 12 13 14 15 16 17 18 19 20
+LUCI
ST
COM
COS
FT
COM
ANT
21 22 23 24 25
COM
PED
PP
CH
AP
28 29 30 31 32
ORO
33
COM
3426 27
RX
TX
12 3 12345
MASTER
F4
COM(-)
COM(-)
COM(-)
COM(-)
Andere Handbücher für CTRL
4
Inhaltsverzeichnis
Andere Roger Technology Zäune & Tore Handbücher
