Roger HRT82MF Bedienungsanleitung

Roger Access Control System

Installation guide for

HRT82MF proximity card reader

Firmware version: 1.0.2.6 or newer

Hardware version: 1.1

Document version: Rev. B

HRT82MF Installation Guide Rev.B

2015-08-13

2/12

1. INTRODUCTION

This manual contains minimum information that is necessary to properly install device. Following

documents supplement this manual:

Functional description of HRC series controllers

Installation guide for HRC series controllers

PR821-CH User Manual

In order to acquire the first one it is necessary to obtain Roger consent and sign non-disclosure

agreement (NDA). The remaining ones are available at www.roger.pl.

2. DESCRIPTION AND SPECIFICATION

HRT82MF proximity card reader is peripheral device used both in a hotel system based on HRC

series controllers and in a hotel system based on PR821-CH controllers. The device communicates

with controller using RACS CLK/DTA bus and enables MIFARE®card number reading for the

purpose of user identification and access granting. The reader enables serial number (CSN) reading

for such cards as MIFARE Ultralight/Classic/Plus/Desfire. Additionally it allows to read configurable

Mad Sector Number (MAD) and Sector Serial Number (SSN) as well as combinations of CNS and

MSN or SSN for MIFARE Classic cards.

HRT82MF front panel includes touch button and four LED indicators for signalling such hotel

indications as ‘hotel staff presence’, ‘do not disturb’, ‘make up room’ and ‘assistance’. The device is

equipped with front panel backlight and buzzer.

Table 1. Specification

Supply voltage

Nominal 12VDC, min./max. range 10-15VDC

Proximity cards

13.56MHz in acc. with ISO14443A and MIFARE

Reading distance

Up to 15 cm for ISO cards (depends on card type and quality)

Average current

consumption

60mA

Tamper resistance

Isolated contact, NC type (normally closed when enclosure is assembled

and attached), 24V/50mA

Distance

Between controller and HRT device (RACS CLK/DTA): max. 150m

Environmental class

(acc. to EN 50131-1)

Class II, indoor general conditions, temperature: -10°C- +50°C, relative

humidity: 10 to 95% (no condensation)

IP code

IP41

Dimensions HxWxD

85 x 85 x 22 mm

Weight

~ 100g

Certificates

HRT82MF Installation Guide Rev.B

2015-08-13

3/12

3. INSTALLATION

3.1 Terminals and connection diagram

Fig. 1 HRT82MF card reader

Table 2. HRT82MF terminals

Term.

Description

Term.

Description

12V

12VDC power supply

CLK

RACS CLK/DTA bus

GND

Ground

DTA

RACS CLK/DTA bus

IN1

not used

TMP

Tamper

IN2

not used

TMP

Tamper

Fig. 2 Connection to controller with 12VDC power supply output

HRT82MF Installation Guide Rev.B

2015-08-13

4/12

Fig. 3 Connection to controller without 12VDC power supply output

3.2 Power supply

HRT82MF requires 12VDC nominal power supply. The power must be connected to 12V and GND

terminals. Additionally, the GND terminal is used as reference potential for the RACS CLK/DTA bus.

HRT82MF power supply can be provided by connection to buffer power supply unit (e.g. PS-15DR,

PS20) or connection to TML output of HRC402DR controller (see fig. 2). Backup battery connected

to power supply unit or directly to HRC402DR controller can be used in order to ensure operation in

case of 230VAC power failure.

Note: All devices connected to the same RACS CLK/DTA bus must be connected to common

reference potential (GND).

3.3 RACS CLK/DTA communication bus

RACS CLK/DTA is the addressable bidirectional communication standard developed and applied in

Roger controllers in order to enable their communication with peripheral devices. Addresses of all

devices connected to CLK and DTA lines must be properly configured in range of 00..15. Standard

unshielded signal cables (e.g. U/UTP cat. 5) with maximal length of 150m can be used for RACS

CLK/DTA communication.

3.4 Front panel

LED indicators

In the top part of HRT82MF reader there are located four icons and LED indicators. Their functions

are explained in table 3 and they depend on type of connected controller.

Table 3. LED indicators

Symbol

Name

Colour

Function

HRC controller

PR821-CH controller

HOTEL

STAFF

Green

Programmable

Presence of hotel staff card in

card holder

MUR

Orange

Programmable

Activated ‘make up room’ flag

ASSIS-

TANCE

Blue

Programmable

Activated ‘assistance’ flag

DND

Red

Programmable

Activated ‘do not disturb’ flag’

HRT82MF Installation Guide Rev.B

2015-08-13

5/12

Touch button

HRT82MF reader is equipped with touch button dedicated to entry bell. However in case of both

HRC and PR821-CH controllers the function is programmable and the button can be used for

various purposes.

3.5 Wall mounting and installation guidelines

HRT82MF consists of front panel and base which are factory assembled and require manual

disassembly prior to installation according to fig. 4.

Installation guidelines

Install device on wall far from sources of heat and moisture

It is recommended to install device on Ø60mm flush mounting box

Front panel and base must be properly oriented in order to ensure functioning of tamper

resistance.

All electric connections must be made with power supply switched off

Run connection wires through hole in device base and then connect wires to screw terminals

If device and controller are supplied from different power supply units then it is necessary

connect GND terminals of both devices

Front panel can be regularly cleaned with wet cloth and mild detergent. Do not clean by means

of abrasive materials and strong cleaners like alcohols, solvents, etc.

Damages resulting from improper maintenance or use are not covered by warranty

HRT82MF Installation Guide Rev.B

2015-08-13

6/12

Fig.4 HRT82MF latches and wall mounting

HRT82MF Installation Guide Rev.B

2015-08-13

7/12

4. CONFIGURATION

4.1 Device programming

The address of factory new HRT82MF is ID=1 and such device is ready to communicate with HRC

series controller requiring no additional configuration. In case of operation with PR821-CH controller

it is necessary to configure the address ID=0.

If necessary, HRT82MF settings can be modified with RogerVDM software (available at

www.roger.pl) after connection to RUD-1 communication interface.

Fig. 5 HRT82MF and RUD-1 connection

Connection and configuration procedure

1. Connect device to RUD-1 communication interface according to fig. 5

2. Place jumper on MEM pins

3. Restart the device (place and remove jumper on RST pins or switch power supply off and on)

4. Install and start RogerVDM software

5. In the opened window select device, firmware version, communication channel and serial port

with connected RUD-1 –see fig. 5

6. Select

Connect

button, the software shall establish connection with the device and automatically

switch to configuration window

7. Enter required settings (configuration window is shown in fig. 7, while options are described in

table 4)

8. Select

Send to Device

button –the software shall upload new settings

9. Remove jumper from MEM pins

10.Restart the device (place and remove jumper on RST pins or switch power supply off and on)

Note:

During connection procedure placing jumper on MEM pins and restarting the device restores its

factory default settings.

HRT82MF Installation Guide Rev.B

2015-08-13

8/12

Fig. 6 Device select window in RogerVDM software

Fig. 7 Configuration window in RogerVDM software

Table 4. Configuration parameters

Parameter

Values

Description

General

Device Name

16 ASCII

characters

Device description which can be filled with any comment by

installer

Transmission Format

RACS CLK/DTA

Address

0..15

Device address on RACS CLK/DTA bus. Default address

ID=1 is required for communication with HRC controller,

while the address ID=0 is required for communication with

PR821-CH controller.

HRT82MF Installation Guide Rev.B

2015-08-13

9/12

Communication

timeout

0..255

The device signals communication failure when selected

timeout [0.5s] elapses. When 0 is selected then failure is

not signalled at all.

Optical Signalization

Keypad Backlight

Level

0..100%

Keypad backlight level

Backlight Animation

On, Off

When activated, panel will temporary switch on keypad full

backlight when card is read or key is pressed and dim the

backlight afterwards.

Backlight Dim

On, Off

When activated, panel will temporary switch off keypad

backlight when card is read or key is pressed.

Acoustic Signalization

Buzzer loudness

level

0..100%

Buzzer loudness level. Buzzer is switched off when 0 level is

selected

Card Read

Confirmation Signal

on Buzzer

Yes, No

When activated, card reading is signalled with buzzer.

Key Press

Confirmation Signal

On Buzzer

Yes, No

When activated, button pressing is signalled with buzzer.

CSN Number Settings

CSN Number of

Bytes

0..8

The parameter specifies how many bytes of read only Chip

Serial Number (CSN) is used in UID card number.

Mifare Classic Settings

Card number

CSN, MSN.

SSN

When CNS is selected then UID includes only this number.

When MSN or SSN is selected then it is possible to use

administrator defined UID. It is also possible to define UID

consisting partially of CSN and MSN or SSN.

Format

BIN, HEX

ASCII

Card number format. When BIN is selected then bytes from

card correspond to UID number. When HEX ASCII is

selected then bytes from card correspond to UID in ASCII

hexadecimal format.

LSB

0..15

The location of MSN or SSN first byte.

MSB

0..15

The location of MSN or SSN last byte.

Sector ID

0..39

Sector number with SSN. For MSN this setting is disabled.

AID

0000..FFFF

AID number in MAD sector which defines sector with MSN.

For SSN this setting is disabled.

Block ID

0..14

Block number in the sector with MSN or SSN.

Key Type

A, B , Roger

Type of key used for reading MSN or SSN.

Key

00000000000..

FFFFFFFFFFFF

Six bytes key used for reading MSN or SSN.

Advanced Settings

Stop Card/PIN

Reading When

Buffer is Full

yes, no

When activated, Card/PIN reading is stopped until buffer is

empty.

HRT82MF Installation Guide Rev.B

2015-08-13

10/12

Card/PIN Buffer

Timeout

The device periodically resets its Card/PIN buffer when

selected timeout [0,5s] elapses. When 0 is selected then

buffer reset is off.

Card/PIN Frames

Encryption

When activated, frames with data from Card/PIN buffer are

encrypted (EEA).

4.2 Firmware update

HRT82MF firmware can be updated with RogerVDM (available at www.roger.pl) after connection to

RUD-1 communication interface.

Firmware update procedure

1. Connect device to RUD-1 communication interface according to fig. 5

2. Install and start RogerVDM software

3. Close

Select Device

window

4. In top menu select

Tools->Update firmware

5. In the opened window select device, port with connected RUD-1 and specify path to firmware

file (*.hex) –see fig. 8

6. According to displayed message place jumper on FDM pins and restart the device (place and

remove jumper on RST pins or switch power supply off and on)

7. Select

Update

button

8. After firmware upload remove jumper from FDM pins and reset device (place and remove

jumper on RST pins or switch power supply off and on)

Fig. 8 Firmware update window in RogerVDM software

4.3 Memory reset

In order to restore HRT82MF factory default settings place jumper on MEM pins and then restart

the device either by placing and removing jumper on RST pins or by switching power supply off and

on. Moreover, memory reset is also part of connection and configuration procedure (see 4.1).

Inhaltsverzeichnis

Andere Roger Kartenleser Handbücher

Roger

Roger PATROL II Bedienungsanleitung

Roger

Roger PRTxxLT series Bedienungsanleitung

Roger

Roger PRTxxMF Series Bedienungsanleitung

Roger

Roger MCT12E Bedienungsanleitung

Roger

Roger PRT12EM Bedienungsanleitung

Roger

Roger HRT82MF-CH Bedienungsanleitung

Roger

Roger RUD-3 Bedienungsanleitung

Roger

Roger PRT12LT Installationsanleitung

Roger

Roger RUD-2 Bedienungsanleitung

Roger

Roger PRT12EM Bedienungs- und Wartungsanleitung

Roger

Roger PRTXXEM Bedienungsanleitung

Roger

Roger PRT12MF-DES Bedienungsanleitung

Roger

Roger RFT1000 Bedienungsanleitung

Beliebte Kartenleser Handbücher anderer Marken

Lindy

Lindy 43185 Bedienungsanleitung

Lindy

Lindy 43185 Bedienungsanleitung

ViziT

ViziT RD-4F Bedienungsanleitung

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Bedienungsanleitung

AVID ID

AVID ID AVID1043 Bedienungsanleitung

Conrad

Conrad PCMCIA Bedienungsanleitung

Rosslare

Rosslare DR-6255 Bedienungsanleitung

Lindy

Lindy 51541 Bedienungsanleitung

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Bedienungsanleitung

Johnson Controls

Johnson Controls Kantech tyco ioSmart Bedienungsanleitung

ACS

ACS ACR122L Bedienungsanleitung

Secukey

Secukey S2-MF Bedienungsanleitung

Elecom

Elecom MR-SMC07 series Bedienungsanleitung

Alien

Alien ALR-9800 Bedienungsanleitung

ACS

ACS ACR310 Bedienungsanleitung

Datamars

Datamars R-IN1300 MID Bedienungsanleitung

Alarm Lock

Alarm Lock AL-PRE2 Bedienungsanleitung

xpr

xpr B100PROX-AH Benutzerhandbuch