Roland PX-7B Bedienungs- und Wartungshandbuch

SERVICE NOTES

Issued by RJA

of Roland Corporation.

CC-KWS17058887E0

Oct. 2013 PX-7B, PX-7C

PX-7B

PX-7C

Table of Contents

Keyboard Parts List (PX-7B) ............................................2

Keyboard Parts List (PX-7C)............................................3

Keyboard Assembly Procedure ......................................4

Circuit Board (Low, Mid).................................................9

Circuit Board (High) .......................................................12

Circuit Diagram (Low) ...................................................14

Circuit Diagram (Mid)....................................................16

Circuit Diagram (High) ..................................................18

This service note contains information about repair parts and the repair method of the keyboard section.

For other sections of each model, please refer to each service note.

Revise Information

Dec. 2, 2013 p. 6 Changed grease.

May. 24, 2016 p. 2 Added parts.

Jul. 29. 2016 p. 3 Added the PX-7C keyboard parts list.

Aug. 10, 2016 p. 3 Changed a part code.

Oct. 2013 PX-7B, PX-7C

Keyboard Parts List (PX-7B)

fig.key-PX-7B.eps

9821

10 9

1217 13

1619 16

No. Part Code Part Name Description Q’ty

5100034009 KEYBOARD ASSY PX-7B

1 5100016416 N-KEY C PX-7 (C6200269R0) 7

5100016417 N-KEY D PX-7 (C6200270R0) 7

5100016418 N-KEY E PX-7 (C6200271R0) 7

5100016419 N-KEY F PX-7 (C6200272R0) 7

5100016420 N-KEY G PX-7 (C6200273R0) 7

5100016421 N-KEY A PX-7 (C6200274R0) 7

5100016422 N-KEY B PX-7 (C6200275R0) 8

5100016423 N-KEY A DASH PX-7 (C6200276R0) 1

5100016424 N-KEY C DASH PX-7 (C6200277R0) 1

2 5100016425 S-KEY PX-7 (C6200278R0) 36

3 5100016251 HAMMER-1 FOR N-KEY PX-7 (61100160) 13

5100016252 HAMMER-2 FOR N-KEY PX-7 (61100170) 13

5100016253 HAMMER-3 FOR N-KEY PX-7 (61100180) 13

5100016254 HAMMER-4 FOR N-KEY PX-7 (61100190) 13

5100016255 HAMMER-1 FOR S-KEY PX-7 (611001A0) 9

5100016256 HAMMER-2 FOR S-KEY PX-7 (611001B0) 9

5100016257 HAMMER-3 FOR S-KEY PX-7 (611001C0) 9

5100016258 HAMMER-4 FOR S-KEY PX-7 (611001D0) 9

4******** CHASSIS 88P PX-7 1

5******** SUB CHASSIS 12P PX-7 7

******** SUB CHASSIS 4P PX-7 1

6******** GUIDE HOLDER PX-7 1

7 5100016412 KEYBOARD HOLDER PX-7 (C6300217R0) 6

8 5100016262 GUIDE BUSHING PX-7 88

9 5100019110 KEY CUSHION A PX-7 (C5000254R0) 2

10 5100019663 KEY CUSHION B PX-7 1

11 5100028252 KEY CUSHION E PX-7 1

12 5100019111 HAMMER CUSHION A PX-7 1

13 5100019664 HAMMER CUSHION B PX-7 1

14 5100037315 PWB SET PX-7B 1

15 40011056 SCREW 3X6 BINDING TAPTITE B ZC 12

16 40011312 SCREW 3X8 BINDING TAPTITE P FE BZC 52

17 40012256 SCREW 3X10 BINDING TAPTITE B FE ZC 60

18 5100033937 FLAT CABLE A-1.0-20X230-4/8-0.7X0.05 2

19 5100047674 RUBBER SWITCH 12P 8

Oct. 2013 PX-7B, PX-7C

Keyboard Parts List (PX-7C)

fig.key-PX-7C.eps

9821

10 9

1217 13

1619 16

No. Part Code Part Name Description Q'ty

5100053166 KEYBOARD ASSY PX-7C SV SERVICE ASSY

5100054674

1 5100046363 N-KEY C PX-7C 7

5100046364 N-KEY D PX-7C 7

5100046365 N-KEY E PX-7C 7

5100046366 N-KEY F PX-7C 7

5100046367 N-KEY G PX-7C 7

5100046361 N-KEY A PX-7C 7

5100046362 N-KEY B PX-7C 8

5100046368 N-KEY A DASH PX-7C 1

5100046369 N-KEY C DASH PX-7C 1

2 5100046370 S-KEY PX-7C 36

3 5100048710 HAMMER-1 FOR N-KEY PX-7C 13

5100048711 HAMMER-2 FOR N-KEY PX-7C 13

5100048712 HAMMER-3 FOR N-KEY PX-7C 13

5100048713 HAMMER-4 FOR N-KEY PX-7C 13

5100048714 HAMMER-1 FOR S-KEY PX-7C 9

5100048715 HAMMER-2 FOR S-KEY PX-7C 9

5100048716 HAMMER-3 FOR S-KEY PX-7C 9

5100048717 HAMMER-4 FOR S-KEY PX-7C 9

4******** CHASSIS 88P PX-7 1

5******** SUB CHASSIS 12P PX-7 7

******** SUB CHASSIS 4P PX-7 1

6******** GUIDE HOLDER PX-7 1

7 5100046729 KEYBOARD HOLDER PX-7C 6

8 5100046717 GUIDE BUSHING PX-7C 88

9 5100048726 KEY STOP CUSHION A PX-7C 2

10 5100019663 KEY CUSHION B PX-7 1

11 5100048727 KEY STOP CUSHION B PX-7 1

12 5100019111 HAMMER CUSHION A PX-7 1

13 5100019664 HAMMER CUSHION B PX-7 1

14 5100048968 PWB SET PX-7C 1

15 40011056 SCREW 3X6 BINDING TAPTITE B ZC 12

16 40011312 SCREW 3X8 BINDING TAPTITE P FE BZC 52

17 40012256 SCREW 3X10 BINDING TAPTITE B FE ZC 60

18 5100048969 FLAT CABLE SML2CD-20X222-BDX8(BL)-P1.0-S4 2

19 5100047674 RUBBER SWITCH 12P 8

Oct. 2013 PX-7B, PX-7C

Keyboard Assembly Procedure

Removing the Key

Insert the tip of needle nose pliers into the U-groove on the pivot side and push in the direction of arrow A.

*Before removing black keys, first be sure to remove the adjacent white keys.

*Take care to ensure that the grease applied to the pivot area is not adhered to the rubber switch.

fig.key-release-e.eps

Installing the Key

While hooking the foot of the key under the cushion, align the inner wall of the key with the guide, place it as shown in the figure, and press the area shown by the

dotted line in the direction of the arrow until it engages with the pivot with an audible click.

*Before installing white keys, first be sure to install the adjacent black keys.

fig.key-set-e.eps

Needle nose pliers

Rubber switch

Cushion

Guide

Pivot

Oct. 2013 PX-7B, PX-7C

Installing the Circuit Board

1.Peel off the backing paper of all the double-sided adhesive tape on the circuit board.

2.Align the notch of the circuit board with the tab on the sub-chassis and press the circuit board to the depth of the notch.

3.First, fasten with screws in the round holes.

Set the round holes in the circuit board on the center of the screw holes in the sub-chassis and secure in place.

4.Fasten screws in the slotted holes.

fig.PWB-set-1-e.eps

Sandwich the circuit board.

Position using the notch.

Press in until flush.

#40011312: P-TITE BIND 3X8

Oct. 2013 PX-7B, PX-7C

Application of Grease

Greasing Points

After the key or hammer has been replaced, the specified grease must be applied to the following points as shown in the figure.

fig.key-grease.eps

1.MORICOAT G-1039...........pink (#17041858)

(a) Key pivot

(b) Hammer pivot

2.FLOIL G-336A............white (#17049543)

(a) Key guide

(b) Contact between natural key and hammer (actuator area)

The Reasonable Amount of Grease

fig.key-grease-1a.eps

1-(a) Key pivot

fig.key-grease-1b.eps

1-(b) Hammer pivot

fig.key-grease-2b.eps

1-(c) Contact between sharp key and hammer

fig.key-grease-2a.eps

2-(a) Key guide

fig.key-grease-2b.eps

2-(b) Contact between natural key and hammer

1-(a)

1-(b) 2-(a)

1-(c), 2-(b)

Oct. 2013 PX-7B, PX-7C

Regarding Hammer Placement

Hammers that have differently shaped metal and plastic portions are arranged as shown in the figure below. When replacing, be very careful not to position the

hammers incorrectly.

*Installation at an incorrect location may impede key touch.

fig.key-hammer-1-e.eps

fig.key-hammer-2-e.eps

The colors of the plastic portion differ.

White key = white

Black key = black

Refer to the photos in the chart below.

The shape of the metal part differs according to the

frequency range.

Verify by comparing the stamp on the part surface

against the chart below.

PX-7 N-KEY HAMMER-1

#5100016251

#5100048710

PX-7 N-KEY HAMMER-2

#5100016252

#5100048711

PX-7 N-KEY HAMMER-3

#5100016253

#5100048712

PX-7 N-KEY HAMMER-4

#5100016254

#5100048713

PX-7 S-KEY HAMMER-1

#5100016255

#5100048714

PX-7 S-KEY HAMMER-2

#5100016256

#5100048715

PX-7 S-KEY HAMMER-3

#5100016257

#5100048716

PX-7 S-KEY HAMMER-4

#5100016258

#5100048717

A0 F#2 G2 E4 F4 D6 D#6 C8

Natural Key

Sharp Key

Oct. 2013 PX-7B, PX-7C

Affixing the Cushion

The cushions are of five types. Position each according to the instructions in the figure.

fig.key-cushion-e.eps

Affix with no meandering, protrusion, peeling, or the like.

If Hammer Cushion B (#5100019664) rubs against the surface, it may raise a nap. Affix pressed down from above so that no rubbing occurs.

The cushions are all cut longer than the overall length of the chassis. After affixing, trim the protruding portions.

#5100028252 or #5100048727:

KEY CUSHION E (white)

Align with the edge of the Guide Holder.

#5100019110 or #5100048726:

KEY CUSHION A (white)

Position flush against the edge

of the metal-plate chassis.

#5100019110 or #5100048726:

KEY CUSHION A (white)

Position flush against the edge

of the metal-plate chassis.

#5100019664:

HAMMER CUSHION B (white/gray, 2 layers)

Align with the edge of the opening in the chassis.

#5100019663: KEY CUSHION B (white)

Position flush against the front edge

of the plastic sub-chassis.

#5100019111:

HAMMER CUSHION A (white/gray, 2 layers)

Position flush against the front edge

of the plastic sub-chassis.

Oct. 2013 PX-7B, PX-7C

Circuit Board (Low, Mid)

Low

fig.b-L1.eps@L

fig.b-L2.eps@L

Mid

fig.b-M1.eps@L

fig.b-M2.eps@L

Oct. 2013 PX-7B, PX-7C

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Roland Musikinstrument Handbücher

Roland

Roland Fantom-X Betriebsanleitung

Roland

Roland VS-1680 V-XPANDED Bedienungsanleitung

Roland

Roland Atelier AT-90R Bedienungsanleitung

Roland

Roland V-Piano Bedienungsanleitung

Roland

Roland FR-2 V-Accordion Bedienungsanleitung

Roland

Roland RD-700SX Bedienungsanleitung

Roland

Roland HP107 Bedienungsanleitung

Roland

Roland VS-2000 Montage- und Bedienungsanleitung

Roland

Roland FR-3X V-Accordion Bedienungsanleitung

Roland

Roland Music Atelier AT-45 Bedienungsanleitung

Roland

Roland HP 236 Bedienungsanleitung

Roland

Roland VXpanded VS-880 Benutzerhandbuch

Roland

Roland RD-100 Bedienungs- und Wartungshandbuch

Roland

Roland VS-890 Bedienungsanleitung

Roland

Roland FP-90X Bedienungsanleitung

Roland

Roland FP-7F Bedienungsanleitung

Roland

Roland KR-115 Bedienungsanleitung

Roland

Roland V-ACCORDION FR-7 Bedienungsanleitung

Roland

Roland RD-700 Kurzanleitung

Roland

Roland Rhythm 77 Bedienungsanleitung

Roland

Roland KF-7 Bedienungsanleitung

Roland

Roland FP-5 Bedienungsanleitung

Roland

Roland RG-7 Bedienungsanleitung

Roland

Roland HP 5700 Bedienungsanleitung

Beliebte Musikinstrument Handbücher anderer Marken

Kawai

Kawai CN17 Bedienungsanleitung

Yamaha

Yamaha PCY130 Bedienungsanleitung

Korg

Korg SP-170S Bedienungsanleitung

Johannus

Johannus Rembrandt 200 Bedienungsanleitung

Yamaha

Yamaha Clavinova CVP-709 Bedienungsanleitung

Yamaha

Yamaha Clavinova CVP-609 Bedienungsanleitung

Casio

Casio celviano ap-700 Bedienungsanleitung

Yamaha

Yamaha PSR-E473 Bedienungsanleitung

Modulus

Modulus Quantum Series Bedienungsanleitung

Gear4music

Gear4music SDP-4 Bedienungsanleitung

HOMCOM

HOMCOM 390-006 Bedienungsanleitung

Xotic Guitars

Xotic Guitars ProVintage Series Bedienungsanleitung

Sadowsky

Sadowsky MetroLine Series Bedienungsanleitung

Bosendorfer

Bosendorfer CEUS Bedienungsanleitung

Gewa

Gewa UP 260 G Bedienungsanleitung

Casio

Casio TONEBANK MT-750 Bedienungsanleitung

Yamaha

Yamaha Electone EL-17 Bedienungsanleitung

Alesis

Alesis AHB-1 Bedienungsanleitung