Rollerdor RD1X2 Bedienungsanleitung
Rollerdor RD1X2 Control Box, Edition 2022/1
RD1X2 Control Box
Installation guide for Roller Shutters with no vehicle/pedestrian access
Edition 2022/1
2
Rollerdor RD1X2 Control Box, Edition 2022/1
1. INSTALLING RECEIVER BOX
1 Remove the lid of the receiver box by squeezing
each side at the bottom where the wires come
into the box (fig.1A).
2 Place the Receiver box on the wall with the cable
pointing downwards at a comfortable height to
operate the push buttons, but out of the easy reach
of children. Between 1500mm up from the floor and
300mm down from the roof/ceiling is recommended.
3 Making sure the box is square, mark the three
fixings (one top and two bottom), then drill and
secure with fixings (fig.1B).
4 Remove the green 4 terminal block in the bottom
left corner and you will see letters printed
on the circuit board.
5 Wiring as follows (fig.2 & fig.3);
Pre wired Mains Power:
N– Neutral / Blue power cable
L– Live / Brown power cable
Earth – Earth power cable
Motor:
L– Brown motor cable (4 core)
R– Black motor cable (4 core)
Earth – Earth connection motor cable (4 core)
N– Blue motor cable (4 core)
Safety Brake:
Remove red link wire from G and S, wire 2 core
cable as follows;
G– Blue safety break cable (2 core)
S– Brown safety break cable (2 core)
fig.2 (no safety brake)
fig.3 (safety brake)
DELETING REMOTE CONTROL HANDSET’S MEMORY
1 Press and release the black programming button located at the top middle of the receiver box just below
the fixing screw, the green LED will start to flash (fig.1).
2 Press and hold the black programming button again and the green LED will start to flash faster.
When this happens, release and press again one more time, the green LED will go out.
3 Test to see if remote operates barrel.
Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required.
fig.1
A
A
B
B
B
3
Rollerdor RD1X2 Control Box, Edition 2022/1
2. PROGRAMMING REMOTE
CONTROL HANDSETS
DIRECTION OF ROTATION
1 Press and hold the top right button ( ) on the handset and the barrel should start turning in the
downwards direction. Should the barrel be turning in the up direction, press the bottom right stop
button ( ) so the barrel stops and then move the right of the two dip switches up (fig.5B).
2 Press and hold the top right button ( ) on the handset, and the barrel should start turning in the
downwards direction.
3 Press and hold the bottom button ( ) on the side of the receiver box and the barrel should start turning
in the downwards direction. Should the barrel be turning in the up direction, press the middle button ( )
on the side of the receiver box so the barrel stops and then move the single dip switch up (fig.5C).
4 Press and release the down button ( ), if the barrel continues in closing direction, press the middle
button ( ) and flick the left of the 2 dip switches up (fig.5A), You should now have to press and hold
the down button ( ) to rotate the barrel in the close direction.
1 Slide the cover down on the remote control handset
and you will see there are four buttons (fig.4).
2 Press and hold the top le button ( ), then press and
hold the top right button ( ), if the barrel moves then
the handset is already programmed in. Repeat with all
other handsets and, if all are programmed, proceed
to ‘Direction of Rotation Section’, if not then carry on
with step 3.
3 With the handset in your hand, press and release
the black programming button located at the top
middle of the receiver box just below the fixing
screw (fig.5D). The green LED will start to flash.
4 Press and hold the bottom le programming button
on the handset ( ). The green LED will flash faster
and go out.
5 Press and hold the top le button ( ), then press
and hold the top right button ( ) to test. The barrel
should move. Repeat with all other handsets that
need programming.
fig.4
D
Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required.
fig.5
C
A
B
D
4
Rollerdor RD1X2 Control Box, Edition 2022/1
3. OPTIONAL EXTRAS
HARD WIRED ROCKER / KEY SWITCH
WIRING AS FOLLOWS:
Receiver Box Green 6 Block Terminal (fig.6)
U– Up wire from switch
D– Down wire from switch
G– Common wire for the supply to the switch
Key Switch (fig.8):
Right Block 13 – Up wire
Left Block 14 – Down wire
Right Block 14 – Common wire for the supply to the switch
Left Block 13 – Right Block 14 Link wire between terminals
To open key switch remove screw then turn key
a quarter turn.
Rocker Switch (fig.7):
4 – Up wire
3 – Down wire
5 – Common wire for the supply to the switch
5 – 2 Insert Link wire between terminals
To open rocker switch remove screws.
fig.7
fig.8A
fig.8B
Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required.
fig.6
Link wire
Up wire
Down wire
Common wire
Rollerdor RD1X2 Control Box, Edition 2022/1
Rollerdor Ltd
10 & 12 Jarrold Way
Bowthorpe Employment Area
Norwich
Norfolk NR5 9JD
+44 (0)1603 743215
sales@rollerdor.net
www.rollerdor.net
Company Registration Number. 10676267
Registered Oice Address:
Rollerdor Ltd, Bankside 300 Peachman Way,
Broadland Business Park, Norwich,
Norfolk, United Kingdom, NR7 0LB
Edition 2022/1
Inhaltsverzeichnis
Andere Rollerdor Steuereinheit Handbücher
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
