Ronix 5901 Bedienungsanleitung
CUT OFF SAW
5901
USER MANUAL 1
SPECIFICATION
Model 5901
Power 2300W
Voltage 220V
Frequency 50Hz
No load speed 4000RPM
Blade size 355mm
Max Cutting capacity
Round Steel 130mm
Square Steel 120mm
Rectangle Steel 120X130mm
Angle Steel 140X140mm
Net weight 17Kg
PART LIST
Base Plate
Abrasive
Cutting Blade
Fixed Guard
Movable
Safe Guard
Fixed Jaw
Movable
Jaw
Nut
Rod Assembly
Hex Key
CUT OFF SAW
2
GENERAL SAFETY INSTRUCTIONS
WARNING!
Read all instructions. Failure to follow all instructions listed below may
result in electric shock, re and /or serious injury.
The term “power tool” in all of the warnings listed below refers to your
mains operated power tool.
SAVE THESE INSTRUCTIONS
.WORK AREA
- Keep work area clean and well lit. Cluttered and dark areas invite accidents.
- Do not operate power tools in explosive atmospheres, such as in the
presence of ammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
- Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
.ELECTRICAL SAFETY
- Power tool plugs must match the outlet. Never modify the plugs in any
way. Do not use any adapter plugs with earthed power tools. Unmodied
plugs and matching outlets will reduce risk of electric shock.
- Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
- Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
- Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
- When operating a power tool outdoors, use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk
of electric shock.
- If operating a power tool in a damp location is unavoidable, use
USER MANUAL 3
a residual current device (RCD) protected supply. Use of an RCD
reduces the risk of electric shock.
.PERSONAL SAFETY
- Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power too while you are tired or under
the inuence of drugs, alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
- Use safety equipment. Always wear eye protection. Safety equipment
such as dust mask, no-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.
- Avoid accidental starting. Ensure the switch is in the off position before
plugging in. Carrying power tools with your nger on the switch or plugging
in power tools that have the switch on invites accidents. Prevent unintentional
starting. Ensure the switch is in the off-position before connecting to
power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your nger on the switch or energizing
power tools that have the switch on invites accidents.
- Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may
result in personal injury.
- Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
- Dress properly. Do not wear loose clothing or jeweler. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jeweler or
long hair can be caught in moving parts.
- If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used.
Use of these devices can reduce dust related hazards.
.POWER TOOL USE AND CARE
- Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at
CUT OFF SAW
4
the rate for which it was designed.
- Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and
must be repaired.
- Disconnect the plug from the power source before making any adjustment,
changing accessories, or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
- Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands of untrained users.
- Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tools operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools.
- Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to control.
- Use the power tool, accessories and tool bits etc., in accordance with
these instructions and in the manner intended for particular type of
power tool, taking into account the working conditions and the work
to be performed. Use the power tool for operations different from those
intended could result in a hazardous situation.
- Save all warnings and instructions for future reference.
.SERVICE
Have your power tool serviced by a qualied repair person using only
identical replacement parts.
This will ensure that the safety of the power tool is maintained.
IMPORTANT:
Hold power tool by insulated gripping surfaces, when performing an operation
where the cutting accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a “live” wire may make exposed metal parts
of the power tool “live” and could give the operator an electric shock.
USER MANUAL 5
.SAFETY
- Read these instructions before operating this power tool. They contain
information which will enable you to use the tool safely and help protect
those around you.
- A copy of this instruction leaet should be kept with the tool so that you
can refer to it quickly when undertaking work. Another copy should be
made and safely away.
- The cut off machine must be put on the ground to use (Do not equip it
on the working table).
- Pay attention to the highest rotational speed limitation indicated on the
cutting wheel; do use it according to the stipulations. It’s limited to use
the glass ber reinforce cutting wheel with safety linear velocity not less
than 80m/s. It’s forbidden to use any other grinding cutting disk.
- Do check if there’s any ssure or damage situation of the cutting wheels
before using the machine every time. If there’s such situation, it must
be replaced to avoid any accidents
- Do equip the cutting wheel according to the operation explanations, use
wrench to x the cutting wheel carefully, it’s possible to occur dangers
if equips too loose; and it’ll damage the cutting wheel if equips too tight.
- Key factors of inspection in trial operation:
- Check the cutting wheel rstly to conrm its model is conforming to
the requirements of the machine type; the cutting wheel is in good
and complete condition. At the time of starting up the machine, don’t
touch the materials, to ensure it’s starting up under idling condition.
In trial operation, please keep a little far away from the machine to
avoid any possible accidents.
- Please close the current source at once if the cutting wheel stops,
gives noises or vibrates.
- The processing project must be clamped tightly, or it’s possibly to
occur dangers due to the dithering of the project: Make use of the silk
rod handle and plier’s plate to clamp the object tightly, hinge on the
base plate and graduation plate to make processing.
- Please note if the machine is equipped in level, the cushion block can
CUT OFF SAW
6
be put under the other end of long project.
- Please check the guard apparatus is normal and effective or not before
operating the machine.
- After switching on, please wait for the cutting wheel rotates with full
speed, and then begin to cut the project.
- Wear gloves and eye protector to avoid rebound and sustain an injury,
don’t wear too loose clothes and the clothes which easy to be reeled
and tore. Please take notice of bundling your hair if with long hair to
avoid the danger that the hair is reeled into the machine.
- Do use the cutting wheel which edge has been grinded very sharp.
- The hands and body can’t approach the rotating cutting wheel too
near, and of course can’t touch the rotating cutting wheel. Do close the
current source when disassembling, draw out the plug, and please don’t
make such operation until the cutting wheel stops completely. If needing
to clamp the object or changing the position and angle of the project,
please wait for the tool stops and then make above-said operations.
- The temperature is very high of project part that is just cut off; don’t
touch it to avoid scald.
- It will decrease the hardness of the cutting wheel if storing it in moist
place, please store it in drying place when not use it, lay it in level to
avoid distortion.
- Don’t damage the axel, pressure board and bolts of the machine, or it
will damage the cutting wheel during the course of assembling it.
- Don’t move the protective shield of cutting wheel because of minding
troubles, or lock the safety protective equipment.
- It’s limited to use the pressure plate attached in the machine.
OPERATION
.ASSEMBLE OR DISASSEMBLE THE CUTTING WHEEL
Before assemble or disassemble the cutting wheel, please make sure the
machine is switched off or unplugged in. The linear velocity of all the cutting
wheels should be no less than 70m/s. The diameter of all cutting wheel
USER MANUAL 7
should be no less than 355mm. Wrench put in the base-wrench, can be
removed when required.
Spanner
Small Flange
Self-Locking pin
Safe Guard
1
When disassemble the cutting wheel, rstly pull up the movable safety
guard and press the self-locking pin to x the cutting wheel; unscrew the
hex bolt counterclockwise with wrench; and then take down the ange
and the cutting wheel.
2
Movable
Safe Guard
Flange
When assemble the cutting wheel, the steps are opposite to the above-said
steps (Picture one, Picture Two, Picture Three)
Make sure to tighten the hex bolts. If not fully tightened, it would lead to
injuries. Please use the supplied wrench to tighten the bolts.
Cutting Blade
Flange
Small Flange
Polt
3
CUT OFF SAW
8
When the cutting wheel is wearing out, it can also be used economically
and efciently by adjusting the height of hexagonal bolts to control the
cutting angle.
Ruler Sheer
Clamp Sheet
Hexagonal
Bolt
4
.THE INTERSPACES BETWEEN THE PLIERS PLATE AND
GRADUATION PLATE
The xed distance is 0-170MM (0-6 11/16 inch) between plier’s plate and
graduation plate, if needing wider interspaces, please adjust the interspaces
according to the under mentioned procedures.
Discharge two hexagonal bolts of the xed graduation plate, move it like the
picture stated, after that, x the hexagonal bolt. According to the adjusting
step, it can attain the under mentioned interspaces setting range. 35-205
MM, 70-240 MM.
Ruler Sheet
Hexagonal Bolt
5
.SETTING OF CUTTING ANGLE
Release the quick-lock device, Move the scale plate to the intended
USER MANUAL 9
cutting angle (0-45°), and screw the quick-lock device tightly (Picture 4).
When the scale plate is set between 35-225mm or 70-260 mm, it cannot
perform diagonal cutting work.
.FIXING WORK PIECE
Turn the handle counter clockwise to lose the movable vice jaw move
the fast nut upward so that the handle can be quickly pulled out or
pushed forward. When pressing the work piece, rstly push forward the
handle until the vice jaw reaches the work piece, then press the fast nut
downwards and turn the handle clockwise to x the work piece (Picture
6). When xing the work piece, make sure to press the fast nut downwards
completely; if not, the work piece cannot be fully clamped, and pop out
cause damage to the cutting wheel.
Trigger
Handle
Screw
Nut
Clamp
Sheet
6
When the cutting wheel is worn out greatly, put a nonammable hard
cushion under the back of the work piece, thus it can use the middle
edge of the cutting wheel to cut the object efciently.
Washer
7
Inhaltsverzeichnis
Andere Ronix Gesehen Handbücher
Ronix
Ronix 5601 Bedienungsanleitung
Ronix
Ronix 5301 Bedienungsanleitung
Ronix
Ronix 5302 Bedienungsanleitung
Ronix
Ronix 5303 Bedienungsanleitung
Ronix
Ronix 5604 Bedienungsanleitung
Ronix
Ronix 5935 Bedienungsanleitung
Ronix
Ronix 4318 Bedienungsanleitung
Ronix
Ronix 5002 Bedienungsanleitung
Ronix
Ronix 4221 Bedienungsanleitung
Ronix
Ronix 5620 Bedienungsanleitung
