Rosco X-Effects LED Projector 5500K Bedienungsanleitung
PLEASE READ & SAVE THESE ORIGINAL INSTRUCTIONS
User Guide
X-Effects® LED Projector
This guide applies to the following X-Effect s models:
X-Effects LED Projector 5500K
Bl ack (297000055001 )
White (297000055002)
Silver (29700005503)
X-Effects LED Projector RGBW
Black (2970000RGBW1)
White (2970000RGBW2)
Silver (2970000RGBW3)
For professional use only. Not for residential use.
www.rosco.com/x-effectsLED 5007481
2
3
TABLE OF CONTENTS
Introduction......................................................................................................................................... 4
Important Safeguards ........................................................................................................................ 4
Unpacking ............................................................................................................................................ 7
Assembly ............................................................................................................................................. 8
Mounting, Controls & Operation ................................................................................................ 16
Ordering Accessories...................................................................................................................... 20
Specifications ....................................................................................................................................24
Warranty ........................................................................................................................................... 26
Information and specifications in this document are subject to change without notice.
Rosco assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual.
X-Eects LED Projector User Guide v1 Copyright ©2017 by Rosco
User Guide
4
INTRODUCTION
Congratulations on your purchase of a Rosco X-Effects LED Projector. The IP65-rated Rosco X-Effects
LED Projector offers the perfect balance of performance, durability and affordability by providing dramatic
illumination effects for a broad range of lighting-applications. Designed to create dynamic lighting effects, the
X-Effects LED Projector is quick and easy to set-up with convenient on-board or remote DMX controls.
To ensure efficient and safe operation, please take a few moments to read this manual completely.
IMPORTANT SAFEGUARDS
The symbols below are used throughout this manual to identify important safety information. Heed all
warnings and safety info on.
Warning, Danger or Caution
Risk of Personal Injury
Risk of Electric Shock
Risk of severe electric shock
5
PREVENTING ELECTRIC SHOCK
• This machine uses mains electrical power at 100-240VAC. When directly contacted, such voltages are
hazardous to human life. Follow all local electrical codes and take precautions when using this product.
• This product is designed to operate from three-wire power systems, where one of the wires is a safety
ground. DO NOT disconnect the safety ground, or use extension cords or adapter plugs to connect this
machine to a two-wire system. Operation without a safety ground may result in hazardous electrical shock.
• Use only extension cords that are of appropriate length and are rated for X-Effects LED’s specified voltage
and current. If an extension cord shows signs of wear or gets warm to the touch, discontinue its use and
obtain a cord with a higher current rating. Improper extension cords are hazardous and may result in poor
performance due to excessive voltage drop.
• Disconnect unit from power source before servicing and when not in use.
6
MAINTAINING SAFE OPERATION
• Do not look directly into the X-Effects LED Projector. Prolonged exposure to the light beam can cause
damage to the eyesight.
• Use only Rosco spare parts and accessories so as to not void the system warranty.
• Allow the unit to cool before attempting to service.
• Rosco X-Effects LED Projectors must only be serviced by a qualified technician.
• Rosco X-Effects LED Projector is not certified for use in hazardous locations
• Rosco X-Effects LED Projector is designed for operation within the range of -4° to 113°F (-20° to +45°C).
• Ensure Rosco X-Effects LED Projector is stored within the range of -4° to 140°F (-20° to +60°C).
7
UNPACKING
Carefully remove the unit from the box.
Do not attempt to operate your Rosco X-Effects LED Projector if there are any signs of physical damage. In
case of damage, contact your Rosco dealer.
8
ASSEMBLY
1.) Insert Effects Glass Gobos
Prior to operating the X-Effects LED Projector, it is recommended that the unit’s Effects Glass Gobos (96mm)
be inserted into the fixture’s Motor Rotation Module.
The Motor Rotation Module can be accessed by loosening the (4) recessed quick-turn screws on the front of
the unit. (Image A)
Carefully remove the front Lens Tube Module and set aside. Check to ensure Effects Glass Gobos are free of
dust, fingerprints and other residue prior to inserting into the projector.
Insert the Effects Glass Gobos into the rotation carriers, ensuring that the flat portions of the effects wheel
flanges are facing each other. Improper orientation of the effects wheels can cause damage to the unit or
may not produce the desired illumination effect. (Image C, D)
Replace the front Lens Tube Module and securely tighten the (4) quick-turn screws.
9
Quick-Turn
Screws
Image A
Image C
Image B
Image D
10
An assortment of Static and Dynamic Gobos and Filters are available as accessories and can be used to
create Blue Water, Red Fire and a wide variety dynamic effects with your X-Effects LED Projector.
Static Filters
Simply insert the X-Effects LED Filter or Gobo into the pocket in the center of the Motor Rotation module,
behind the Dynamic Effects Glass Gobos. (Image B)
Static Filter Part Numbers:
297000000085 X-Effects LED Amber Filter - Fire Effect
297000000090 X-Effects LED Green Filter - Aurora Effect
297000000095 X-Effects LED Blue Filter - Water Effect
120X-YYYY-SXFX X-Effects LED Permacolor Dichroic Glass Filter
(YYYY = four digit color number)
Your X-Effects LED Projector can also be used for static image projections. Simply insert the X-Effects LED
Gobo into the pocket in the center of the Motor Rotation module, and remove any Effects Glass Gobos if
present. (Image B)
Visit the Image Glass page to see all of the available options: www.rosco.com/imageglass
Dieses Handbuch passt für folgende Modelle
13
Inhaltsverzeichnis
Andere Rosco Projektor Handbücher
Beliebte Projektor Handbücher anderer Marken
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung
NEC
NEC NP600S EDU Bedienungsanleitung
BenQ
BenQ SH753P Bedienungsanleitung
Eiki
Eiki EK-623U series Bedienungsanleitung
Epson
Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung
Epson
Epson PowerLite Home Cinema 705HD Bedienungsanleitung
