Rosewill Power Protection UPS RU-103 Bedienungsanleitung

Power Protection UPS RU103 User Manual

RU-103

Rosewill the uninterruptible power system (UPS) protects your sensitive electronic

equipment from power problems such as power failures, power sags, power surges,

brownouts, and line noise.

Features:

•Processor-controlled voltage regulation

•Eight outlets

-Four with surge and backup protection

-Four with surge protection only

•Telephone line surge protection jacks

•Cold start capability

•USB communication port

SAFETY INSTRUCTIONS

Once you have received the UPS product, you should remove and inspect the

product for shipping damage. If any damage is found, please notify the carrier and

your dealer. Please keep the shipping carton and the packing foam in the event the

product must be returned to the factory for service.

A qualified technician must perform maintenance, other than battery replacement.

Failure to do so could result in an electrical shock. Although the unit may be

unplugged from utility power, hazardous voltage still may be present through the

battery.

1. Place the UPS indoors in an area that has adequate airflow and is free from

excessive dust. Do NOT allow the UPS to be exposed to moisture, rain,

excessive heat or direct sunlight.

2. Use of the UPS product in life support applications where failure of this

equipment can reasonably be expected to cause failure of life support

equipment or to significantly affect its safety or effectiveness is NOT

recommended.

3. Always disconnect the input power cord from the wall outlet before replacing the

battery.

4. When replacing the battery, use the same number and type of battery.

5. Do NOT dispose of the battery in a fire: the battery may explode.

6. Do NOT open or mutilate the battery. Batteries contain an electrolyte

that is toxic and harmful to both the skin and eyes.

7. Proper disposal of the battery is required. Please refer to your local

laws/regulations regarding battery disposal.

8. Use tools with insulated handles to replace the battery to avoid personal injury.

Due to energy hazards, please remove wristwatches and jewelry such as rings

when replacing battery.

BATTERY CONNECTION REQUIRED BEFORE USE!

Connecting the Battery!

How to hook up the battery before installing the UPS?

1. Remove the screws from the bottom of the front panel.

2. Grasp the panel cover downward off the UPS.

3. Connect the battery positive wire (red).

4. Put the front panel cover upward.

5. Bolt the screws.

INSTALLATION AND OPERATION:

The following steps explain how to connect and operate the UPS.

1. Connect the UPS to a grounded power outlet.

NOTE: It is recommended that the battery be charged for at least 8 hours to

ensure full charge before placing the UPS in service.

2. Plug your computer, monitor or load to be protected into the “Battery Backup &

Surge Protection” outlets. (These outlets will provide emergency battery backup

power during power problems as well as protection from surges and spikes.)

CAUTION: Do NOT plug LASER PRINTERS into the “Battery Backup”

outlets.

CAUTION: Do NOT plug ACCESSORY SURGE strips into the “Battery

Backup outlets.

3. Plug your peripheral equipment or non-critical loads (printer, scanner,

fax, speaker, etc.) into the “Surge Protection” outlets. (These outlets

provide surge and spike protection only they will NOT provide battery

backup power during a utility power failure).

4. Switch on the UPS while the connected equipment is off.

5. Turn on your connected equipment when the “AC mode” LED light is

illuminated.

INDICATORS

RU-103

＊

1. On/Off Push Button

This On/Off switch controls power to your equipment and performs a

self-test to detect inverter, line, battery status & LEDs.

NOTE: Turn on the UPS.

Press and hold the switch for more than one second and release the

switch after the beep. The UPS will start and provide the stable power to

your equipments.

NOTE: Turn off the UPS.

Press and hold the switch for more than one second and release the

switch. The UPS will shut down completely.

NOTE: Perform Self-test.

The UPS will perform self-test for about 5 seconds when the UPS is

turned on.

2. LCD Choose Button

Click the switch each time it will display the UPS's special status and data’s

on the screen.

3. Fault / Warning (Red) LED

Indicates that a fault condition has occurred.

-Flashing Red LED indicates an overload condition or that the

battery should be replaced.

-Solid On LED indicates that the output is shorted or an internal

UPS fault exits.

See the Indicator Table below for further detail.

4. Backup mode (Yellow) LED

Indicates that the UPS is operating on battery and providing regulated AC

power to the backup only outlets and the connected equipment.

5. AC mode (Green) LED

Indicates that AC utility power is present and regulated power (AVR) is

applied to the connected equipment.

6. LCD Display

State 1: UPS load capacity display.

Load pixel is 20%--40%--60%--80%--100%

State 2: UPS battery capacity display.

Battery pixel is 20%--40%--60%--80%--100%

State 3: UPS input/output voltage & frequency display.

Click the LCD choose switch, it will cycle display input

voltage, input frequency, output voltage and output

frequency on the screen.

Power Protection UPS RU103 User Manual

7. USB Communication Port

The built-in USB port connects to your computer. The PowerGuard Smart

monitoring and shutdown software provided can automatically save your files

and shut down your computer in the event of a prolonged power outage. The

software also provides information regarding the status of your utility power

line

Installing software

If autoplay is not enabled on the computer, please follow instructions below:

‧Double-click on My Computer on the desktop.

‧Double-click on the CD-ROM drive icon and follow the on-screen

instructions.

8. Data /Phone/Fax Protection Connectors

9. “Surge Only” Outlets

Four Nema 5-15R output receptacles that will provide surge and spike

protection only

10.“Battery & Surge” Outlets

Four Nema 5-15R output receptacles that will provide both battery backup and

surge protection.

11.AC Input Power Cord

Plug the AC power cord into your power source

12.Coax in :

TV/TNT/Satellite reception protection

13.Circuit Breaker (re-settable)

The button will protrude when the overload condition occurs. If the button

protrudes, disconnect some non-essential equipment and reset the circuit

breaker by pushing the button inward.

14.Coax out:

TV/TNT/Satellite reception protection

INDICATOR TABLE

Status Indicators

The UPS provides both visual and audible status indicators. Visual indicators consist

of three LEDs to represent the following conditions:

•On utility power operation

•On battery power operation

•UPS fault/alarm

LED and Alarm Indicator Table

UPS Status Green

LED

Red LED Yellow

LED

Alarm

Self-test Blink 1 B1

Normal On X X X

Self Low

battery

On Blink2 X B5

AC mode

( on utility)

overload On Blink2 X B2

Normal X X On B1

Low

battery

X X Blink2 B3

DC mode

( on battery)

Overload X Blink2 On B2

Short/Fault mode X On X On

Over-Bat/Bat Fault X Blink2 X B4

* Blink 1 : ON 0.5 seconds / OFF 1 seconds

* Blink 2 : ON 0.25 seconds / OFF 0.25 seconds

* B1: 1 beep / 5 seconds: ON 0.25 seconds / OFF 4.75 seconds

* B2: 1 beep / 0.5 seconds :ON 0.25 seconds / OFF 0.25 seconds

* B3 : 2 beeps / 5 seconds: ON 0.25 seconds / OFF 0.25 seconds 2 times, 4 seconds OFF

* B4 : 3 beeps / 5 seconds: ON 0.25 seconds / OFF 0.25 seconds 3 times, 3.5 seconds OFF

* B5: 3beeps / 30seconds :ON 0.25 seconds / OFF 0.25 seconds 3 times, 28.5seconds OFF

Recycling Information:

Your UPS contains Non-Spill Sealed Lead Batteries. On the battery you will

find the battery name. Please reference the chart below for recycling

information. Other brand(s) of battery please contact Rosewill.com.

Battery Name Recycling inside the USA

Vision Battery 1-877-730-2877

First Power Battery 1-877-730-2877

BB Battery 1-800-278-8599

Follow the on-screen

instructions.

SPECIFICATIONS

Model RU-103

Capacity 1500 VA / 900W

Nominal Input Voltage 120 Vac

Nominal Output Voltage 120 Vac

Automatic Voltage

Regulation (AVR) 108-130Vac(±3%)

Frequency 50 / 60 Hz auto sensing

8 Outlets (4 Battery Backup & Surge Protection;

4 Surge Protection only)

Outlets

Lighting / Surge Protection 320 Joules

Transfer time to Battery/AC 2-6ms typical

Battery Type Maintenance free lead-acid battery

(2)* 12V 9 Ah

Battery Specification

Typical Backup Time 4-7 Minutes

RJ11/45LAN / Phone / Fax Protection

Short Circuit Protection Circuit Breaker

Communication Port USB

0°C–40°COperation Temperature

0 to 95% non-condensingOperation Relative Humidity

Storage Temperature -15°C–50°C

Net Weight 29.3 lb

Dimensions (HxWxD) 10.8 x 3.4 x 16.1 IN

Specificationsmaychangewithoutpriornotice.

TROUBLESHOOTING

Symptom Possible Cause Action to Take

Ensure the UPS is securely

connected to an AC outlet.

The UPS is not

connected to the

power source.

UPS will not turn

Circuit Breaker has

tripped.

Reduce the amount of equipment

plugged into the “Battery Backup &

Surge Protection” outlets of the UPS.

Reset the circuit breaker by pushing it

back in. Switch the UPS back on.

Turn off the UPS and reduce the

amount of equipment connected to

these outlets.

The “Battery Backup &

Surge Protection”

outlets are overload.

UPS is making a

continuous

sound and the

“Overload”

indicator is on

The UPS battery is

discharged due to a

power outage and has

not recharged.

Charge the battery for 8 hours. The

UPS runtime is reduced until the

battery is fully charged.

UPS does not

provide

expected

runtime Back-UPS is heavily

loaded.

Unplug non-essential equipment

(printers, scanners, etc) from the

Battery Backup outlets and plug into

'Surge Only' outlets

Disconnect non-essential equipment

from the UPS. Reset (push in) the

circuit breaker and switch the UPS

on.

The UPS circuit

breaker “tripped”.

Plug equipment in one-at-a-time. If

the circuit breaker trips again,

disconnect the device that caused

the breaker to trip.

UPS does not

power essential

equipment

during an outage

Replace the battery or the battery

module.

The battery has

reached the end of its

life.

Unplug device from 'Surge Only'

outlet and move to a 'Battery Backup

outlet.

Equipment plugged

into a Surge Only

outlet.

Flashing

Indicators

Internal UPS fault. Contact Technical Support (see

Service and Support below).

Thank you for purchasing a quality Rosewill Product.

Please register your product at: www.rosewill.com for complete warranty information and future

support for your product.

Technical Support : [email protected]

Call Center : ( 800 ) 575-9885

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rosewill UPS Handbücher

Rosewill

Rosewill RU101 Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung