Rowenta PROACTIVE 032621 - IC7100 - 50/03 Bedienungsanleitung

instructions for use

032621 - IC7100 - 50/03

1 • UNDERSTANDINGYOUR IRONING CENTRE

14 15 1 3 5 7 6 4

12 11 13 9 8 10

1. Iron

2. Electric power cord (iron + board)

3. Steam cord

4. Steam cord support

5. Iron rest-plate

6. Removable water tank

7. Iron, power cord and steam cord storage

space

8. Control panel

9. Steam generator screw-clamps

10. Wheels (rubber-coated to protect delicate

floors)

11. Feet

12.Semi-automatic opening lever (use only to

open the board)

13.Board closing and height adjuster lever

(use this lever to close the board)

14. Heated, active ironing area with ironing

board cover

15.Suction-blower unit

12 6 7 13

a) Control panel

Green "Steam

ready" light

Red "Water tank

empty" light

Steam output

control dial

Main ironing centre power On/Off (O/I)

switch (Controls board + generator)

RESTART button (Restarts heating of

the boiler during use)

b) Heated board with suction and blown-air functions

Board heats up automatically when the ironing centre

is switched on.

Suction function

Inside the board, the suction fan sucks air through the board.

Blown air function

Inside the board, the blower fan blows air through the board.

Board fan control button

suction

blown air

c) Iron d) Steam generator

Steam cord

Soleplate temperature

control dial

Temperature

control light

Steam control

button

Humid steam

button

Screw-clamps

Boiler (inside compartment)

Rubber pads

Iron, power cord and steam cord

storage compartment catches

Cord outlets

ENG

2 • PREPARINGYOUR IRONING CENTRE

1. Always place your ironing board on the floor in a horizontal position. (1)

2. Hold down the ironing board feet under one of your own feet. (2)

3. Use your hand to press the semi-automatic opening lever located underneath the front end of

the board, then raise the board to the required height (2).

4. If the board is too high for comfort, adjust its position using the adjuster lever (3).

5. Lift up and remove the water tank.

6. Unscrew the water tank cap.

7. Fill the water tank, taking care not to exceed the maximum level. (4)

8. Replace the cap on the water tank.

9. Replace the water tank in its housing, pressing down until it clicks into place (5).

98 cm

70 cm

Suitable water:

Your steam generator has been designed to operate using untreated tap water. However, if

your water is very hard, mix 50 % untreated tap water with 50 % distilled water.

The ironing centre comes with a tester that can be used to test the hardness of the water.

Unsuitable water:

Do not add anything to the contents of the removable water tank, and do not use water

from clothes-dryers, scented or softened water, water from refrigerators, batteries or air

conditioners, pure distilled water, pure demineralised water or rainwater, as these types of

water contain organic waste or mineral elements that become concentrated when heated

and cause spitting, brown staining or premature wear to the appliance.

(1) (2)

(3) (4) (5)

3 • USINGYOUR IRONING CENTRE

Open the storage compartment cover by lifting the catches located on each

side of the iron rest-plate (6).

Remove the iron, steam cord and electric power cord from the storage com-

partment. (7)

Insert the power cord and steam cord in the cut-outs located on the sides of

the storage compartment.The ironing centre can be configured for left- or

right-handed use.

Close the storage compartment cover and place the iron on its rest-plate (8).

Warning :Your ironing centre is equipped with a safety device which cuts the power supply

when the iron is stored in its compartment.

To switch the iron on again, it is imperative that the iron is removed from its storage com-

partment first.

5. For maximum ironing comfort, fit the steam cord support in its mounting and feed the steam

cord through the support loop (9).

6. Connect the power cord to an earthed mains socket.

7. Switch on the main On/Off (O/I) switch (located on the control panel on the ironing board)

(10 - 1 ).The green light on the control panel will start to flash and the boiler will heat up

(10 - 2 ). When the green light stops flashing (after approximately 2 minutes), the steam supply

is ready.

When you switch on your ironing centre, the ironing board surface heats up automatically,

eliminating any risk of steam condensing.Your ironing board's surface will reach its operating

temperature in approximately 7 minutes.This does not prevent you from starting your ironing

as soon as the steam supply is ready (after 2 minutes).

• The first time you use your ironing centre, some fumes and a harmless smell may be released.

They will not affect use and will quickly disappear.

• After about a minute, and at regular intervals during use, your appliance's electric pump will

inject water into the boiler. It makes a noise, but this is quite normal.

(6)

(7) (8) (9) (10)

4 • OPERATINGTHE CONTROL PANEL

- Flashing green light: Water is heating in the boiler.

- Continuous green light:The steam supply is ready for use.

- Continuous red light:The water tank is empty.

- RESTART button: Press this button to restart boiler heating, whenever you have stopped to refill

the water tank (see chapter 9).

ENG

5 • SUCTION AND BLOWN-AIR FUNCTIONS

Your ironing centre is equipped with a range of professional ironing features.

In addition to an automatically heated ironing board surface, your appliance is equipped with

fans providing suction and blown-air functions which ensure outstanding ironing quality.

a) Suction and blown-air fan control button

b)The benefits of the suction and blown-air functions include

BLOWN-AIR FUNCTION:

When you switch the control button to the blown-air position, the blower

system is activated, creating an air cushion between the board and fabric. The

blown-air function is recommended for:

- Ironing delicate fabrics (e.g. silk or wool);

- Preventing accidental creases on large and medium-sized items

(e.g. tablecloths, sheets or jacket backs);

- Avoiding "buffing" fabrics, and preventing lines and seam marks.

SUCTION FUNCTION:

When you switch the control button to the suction position, the suction system is

activated, creating a downward airflow.The suction function is recommended for:

- Holding items in place on the ironing surface;

- Clearly marking creases (e.g. trouser creases);

- Ironing thick fabrics (e.g. denim and linen);

- Eliminating any residual moisture;

- Preventing steam from escaping while you are ironing.

c)Tips for using the suction and blown-air functions according to the type

of fabric

Delicate fabrics: silk, synthetic materials

Delicate finishes: gathers, frills, glitter, embroidery, lace, etc.

Linings and seams: jacket linings, double-layered delicate fabrics, etc.

Thick and heavy fabrics: cotton, denim, corduroy, linen, tweed, wool, etc.

Creases and turn-ups: pleated skirts, trouser turn-ups, knife pleats, etc.

Lined finishes: cuffs, collars, waistbands, hems, button-holes, shirt back pleats, etc.

BLOWN AIR

SUCTION

For a more detailed explanation, please refer to the enclosed booklet entitled "IroningTips", inside

the box.

BLOWN AIR position

Position O (no ventilation)

SUCTION position

6 • STEAM IRONING

Set the iron's temperature control selector according to the type of fabric to be ironed (11)

2. The iron temperature control light will light up.

Important:The ironing centre is ready when the iron temperature control light goes out and

when the green “steam ready light” on the board's control panel stays continuous.

It is perfectly normal for the iron temperature control and boiler lights to switch on and off during

use, according to the heating requirements. This does not prevent you from continuing to iron in

the usual way.

3. Adjust the steam output (using the steam output control dial located on the control panel) (12).

Synthetics (low temperature)

Silk/Wool (medium temperature)

Cotton/Linen (high temperature)

●

●●

●●●

(11) (12)

Set the iron’s temperature control and steam output control dial according to the type

of fabric to be ironed :

Fabric type

Synthetics

Silk / Wool

Cotton / Linen

Iron temperature

control setting

●Low temperature

●● Medium temperature

●●● High temperature

Steam output control

dial setting

(13)

We advise you to begin by ironing any fabrics requiring a low temperature

setting, e.g. synthetics (●)

To obtain steam, press on the steam control button located beneath the iron

handle (13).

The flow of steam will stop when you release the button.

With delicate fabrics (●), press the steam control button under the iron

handle intermittently, to avoid possible water droplets appearing with the

steam.

ENG

Recommendations:

• Before you begin using the iron, or if you have not used any steam for a few minutes, press the

steam control button several times in a row, holding the iron away from your clothes.

This will enable any cold water to be removed from the steam-circuit.

•

Iron temperature control setting:

- Start with any fabrics to be ironed at a low temperature (•), and finish with those which need

higher temperatures (• • • or Max).

- Mixed-fibre fabrics: Set the ironing temperature to the setting for the most delicate fabric.

- Woollen garments : Press the iron’s steam control button intermittently to produce short

bursts of steam, without placing the iron on the garment itself.

•

Steam output control dial setting:

-Thick fabrics: Increase the steam output setting.

- Low temperature ironing: Set the steam output control dial to the low position.

•

Dry ironing:

Do not press the steam control button under the iron handle.

• If you are using starch, it should be sprayed onto the reverse side of the fabric to be ironed.

•

Ironing board cover:

We recommend ironing the ironing board cover with a very hot iron before you use it for the

first time. For perfect results every time, only replace with a Rowenta ironing board cover

available from our authorised service dealers.

7 • VERTICAL STEAM IRONING

1. Set the iron temperature control and the steam output control dial (located

on the control panel) to the maximum position.

2. Hang the garment on a coat hanger and hold the fabric slightly taut with

one hand.

As steam is very hot, never attempt to remove creases from a garment

while it is being worn - always hang garments on a coat hanger.

3. Holding the iron in a vertical, tilted position, press in one second bursts on

the steam control button (located beneath the iron handle) while moving

the iron from top to bottom (14).

Recommendations: With fabrics other than linen or cotton, hold the iron a few centimetres

away from the garment, to avoid burning the fabric.

(14)

8 • HUMID STEAM FUNCTION

Press the humid steam button (15) two or three times to obtain a steam

boost as required:

- When ironing thick fabrics,

- In order to eliminate unwanted creases,

- For powerful vertical crease removal.

Important: Use the humid steam function very carefully because of the exceptional power

of the steam that may cause burns.

(15)

9 • WHATTO DO IFTHE RED "WATERTANK EMPTY" LIGHT

COMES ON

You can use your steam generator indefinitely, thanks to its removable water

tank.

The red light (16: 1 ) comes on when there is no more steam.The removable

water tank is empty.

1. Unscrew the water tank cap.

2. Lift up and remove the water tank.

3. Fill the water tank.

4. Replace the cap.

5. Replace the water tank in its housing, pressing down until it clicks into

place (17).

6. Press the boiler RESTART button (16: 2 ) on the control panel to continue

your ironing.

(16)

(17)

10 • MAINTAININGYOUR IRONING CENTRE

•Before cleaning your appliance, ensure that it is unplugged and that the soleplate and the

iron rest-plate have cooled down.

• Do not use any cleaning or descaling products when cleaning the soleplate or boiler.

• Never hold the iron or steam generator under the tap.

• Do not place the iron on a metal rest, as this could damage it.

Place it instead on the supplied rest-plate, which is fitted with non-slip pads and is designed to

withstand high temperatures.

a) Removable water tank

Empty and rinse the removable water tank (18)

(18)

b) Iron soleplate

We recommend that you clean the soleplate using the Rowenta soleplate cleaning stick available

from Rowenta Approved Service Centres (see After Sales Service chart for addresses).

The iron's high quality soleplate protects your laundry and makes ironing smoother.

When you are not ironing, you should always place the iron on its rest-plate; never stand the iron

on its heel.

Do not place the iron on rough surfaces. Do not scratch or scrape the soleplate. Never clean it

with corrosive or abrasive agents.

Never iron over zips or rivets eg on jeans.

c) Ironing board and iron

Clean the plastic parts of the iron and the ironing board legs occasionally by wiping with a damp

cloth.

ENG

d) Ironing board cover

• We recommend ironing the ironing board cover with a very hot iron before

you use it for the first time.

•Washing instructions: machine-washable at 40°C.

•Removing the cover:

1. Loosen the drawstring by pulling the fastener downward (19).

2.You can now remove the cover.

•Replacing the cover:

1. Check that the drawstring is loose by pulling the fastener downward.

2. Spread out the cover, wrapping it all round the board.

3.Tighten the drawstring by moving the fastener upwards.

•Replacement ironing board covers are available. Product reference: ZD 7200.

(19)

11 • RINSING OUTTHE BOILER

Important :

• To extend the life of your boiler and to avoid any build-up of scale, it is essential to rinse

out the boiler after every 10 uses. If your water is hard, you should rinse the boiler more

frequently.

• Never use descaling agents when rinsing out the boiler, as they could damage it.

a) Rinsing the boiler using the rinsing accessory

For easier and more effective boiler rinsing, we recommend using the rinsing accessory supplied

with your ironing station (20).

It will make rinsing the boiler easier as the steam generator will require less handling.

Your rinsing accessory has been designed to fit a wide range of taps. It is supplied with two types

of membrane (21) (a) (b). Choose the one best suited to your tap.

(20) (21)

(a)

(b)

Before rinsing your steam generator, you MUST let your ironing station cool for 2 hours, to

prevent any risk of burns.

Recommendation:

To avoid the need to wait, we recommend rinsing the boiler before you start your ironing

session.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rowenta Eisen Handbücher

Rowenta

Rowenta DZ9000 Bedienungsanleitung

Rowenta

Rowenta Professional DE 873 Bedienungsanleitung

Rowenta

Rowenta DG9040F0 Bedienungsanleitung

Rowenta

Rowenta DW9220 Bedienungsanleitung

Rowenta

Rowenta DW924 Series Bedienungsanleitung

Rowenta

Rowenta POWER DUO 1103465594 Bedienungsanleitung

Rowenta

Rowenta ECO INTELLIGENCE DG8890F0 Bedienungsanleitung

Rowenta

Rowenta IXEO QR10XX Bedienungsanleitung

Rowenta

Rowenta SOFT DX2500D1 Bedienungsanleitung

Rowenta

Rowenta ULTRA STEAM Bedienungsanleitung

Rowenta

Rowenta EFFECTIVE Bedienungsanleitung

Rowenta

Rowenta DW5080 Bedienungsanleitung

Rowenta

Rowenta Master DW9055U1 Bedienungsanleitung

Rowenta

Rowenta DX1100F1 Bedienungsanleitung

Rowenta

Rowenta DA1510F1 Bedienungsanleitung

Rowenta

Rowenta PROFESSIONAL DW8050U5 Bedienungsanleitung

Rowenta

Rowenta DW5000 Bedienungsanleitung

Rowenta

Rowenta DW5000 Bedienungsanleitung

Rowenta

Rowenta DW5000 Bedienungsanleitung

Rowenta

Rowenta DG8980 Bedienungsanleitung

Rowenta

Rowenta DW8116D1 Bedienungsanleitung

Rowenta

Rowenta DG8990 Bedienungsanleitung

Rowenta

Rowenta DG5030 Bedienungsanleitung

Rowenta

Rowenta ECO INTELLIGENCE Bedienungsanleitung

Beliebte Eisen Handbücher anderer Marken

Clatronic

Clatronic DB 3703 Bedienungsanleitung

TEFAL

TEFAL FV4093Z0 Bedienungsanleitung

Gorenje

Gorenje SIH 2200 BS Bedienungsanleitung

Philips

Philips GC6012 Bedienungsanleitung

Bosch

Bosch 2 Series Bedienungsanleitung

Riffel

Riffel Catena KB-819 Bedienungsanleitung

Texi

Texi Hestia Bedienungsanleitung

Maxwell

Maxwell MW-3010 Bedienungsanleitung

TREVIDEA

TREVIDEA Girmi ST60 Bedienungsanleitung

Philips

Philips HI5914/30 Bedienungsanleitung

Primula

Primula Vapormat Bedienungsanleitung

Magio

Magio MG-541 Bedienungsanleitung

Scarlett

Scarlett SC-1334S Bedienungsanleitung

Bosch

Bosch Sensixx B22L Bedienungsanleitung

Philips

Philips GC651 Bedienungsanleitung

Vitek

Vitek VT-1247 VT Bedienungsanleitung

Cleanmaxx

Cleanmaxx 3397 Bedienungsanleitung

Philips

Philips GC800 Bedienungsanleitung