Rowley R-TEC Automation RTMHR5C Bedienungsanleitung

R-TEC Smart Controls - Handheld Remote, 5 Channel

5 Channel Handheld Remote with Wall Mount fuses luxury and functionality in a

well-crafted, minimal design.

The 5 channel remote features soft tactile rubber buttons that can control 5

individual or 5 groups of window treatments, as well as an “ALL” button that

conveniently activates all programmed channels.

Handheld remotes are compatible with all ARC™ motors.

FEATURES - 5 CHANNEL

Slim

Magnetic

Wall Mount

Tactile

Buttons

2-Way RF

Communication

Distinct Slim

Design

RTMHR5C

Durable

Build

Technical Data / Pack Contents 3

Safety 4

Installation 5

Wall Mounting

Remote Battery

Functional Overview 6 - 7

Buttons

Selecting a Channel

Group Control

Programming 8 - 9

Quick Start Programming

Set a Favorite Position

Disable Limit Setting Function of Remote

Adding or Removing Controllers & Creating Group Channels 10

Using Motor P1 Button

Using a Pre-Existing Controller

Troubleshooting 11

TABLE OF CONTENTS

Parameters Value

COMPLIANCE STATEMENT

TECHNICAL DATA / PACK CONTENTS

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference that may cause undesired operation.

PRODUCT SPECIFICATIONS

Voltage 3 V DC

Battery CR2430

Radio Frequency 433.92 MHz

Transmitting Power 10 milliwatt

Transmission Range 65'

Temperature Working Range 50º F - 122º F (10º C - 50º C)

PACK CONTENTS

1. Handheld Remote with Wall Mount, 5 Channel

2. Cradle and Wall Fixing Screws

3. Instruction Manual

4. 3 V - CR2450 Battery

5. Screwdriver

SAFETY

Any changes or modiﬁcations to this unit not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment. Incorrect installation can lead to serious injury and will void

manufacturer’s liability and warranty.

WARNING

Do no dispose of in general waste.

Please recycle batteries and damaged electrical

products appropriately.

CAUTION

• Do not expose to moisture or extreme temperatures.

• Do not allow children to play with this device.

• Use or modiﬁcation outside the scope of this instruction manual will void warranty.

• Installation and programming to be performed by a suitably qualiﬁed installer.

• Use only R-TEC Automation®hardware.

• Keep clear when in operation.

• Replace battery with correctly speciﬁed type.

IMPORTANT SAFETY INSTRUCTIONS TO BE READ PRIOR

TO OPERATION

• It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference.

• Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge

should not be allowed to use this product.

• Frequently inspect for improper operation. Do not use if repair or adjustment is necessary.

• Keep away from children.

WALL MOUNTING

REMOTE BATTERY

INSTALLATION

Use supplied fasteners and anchors to attach the base to wall.

Replace cover by pressing snap latches into place.

Remove cover from remote;

unscrew with screwdriver included,

then ﬁrmly press down and slide left.

Insert battery as directed, then slide

cover back on remote and screw on

with screwdriver included.

BUTTONS

FUNCTIONAL OVERVIEW

SELECTING A CHANNEL

SETTING (P2)

LOCK

STOP

DOWN

CHANNEL

ALL

When a channel is selected, the blue LED will stay illuminated for four seconds and then go out. The channel remains active.

Programming and operation of the window treatment(s) on the channel can proceed without reselecting the channels.

IMPORTANT

To determine which channel is activated prior to programming or operating the control simply press and release any of

the ‘channel’ buttons or the ‘stop’ button once and the active channel or channels will illuminate.

IMPORTANT

You can program one channel at a time but you can operate several channels at once if desired after the programming

has been completed.

IMPORTANT

Select a channel by ‘toggling’ it on until a blue LED is

showing next to it. This will require pressing and releasing

the channel once or twice until the light appears.

ALL

Deselect the channels that you don’t

want to be active by ‘toggling’ them off

until the blue LED disappears.

Now only the channel that you want to program or operate will be active.

Your selected channel is now ready to be programmed or operated.

ALL

GROUP CONTROL

Channel ALL is preset to control all window treatments paired to your multi channel remote.

ALL

Please refer to the relevant documentation of your motor model for instructions on adjusting motor settings.

Select a single or multiple channels by

toggling channels (3) as required.

Note the corresponding LED next to

each channel.

PROGRAMMING

IMPORTANT

QUICK START PROGRAMMING

Approx.

Motor Response

Hold P1 button on motor

head for 2 seconds until the

motor responds as below.

* Internal Tubular

pictured. Refer to

P1 LOCATIONS on page

10 for speciﬁc devices.

Motor Response

Approx.

Within 4 seconds, hold the

STOP button on remote for

3 seconds. The motor will

respond as below.

ALL

Repeat steps 1-6 for all motors.

Once complete, press and hold

the LOCK button for 6 seconds

while looking at the LED, and

hold until solid.

Move window treatment to desired top

limit by pressing the UP arrow repeatedly.

Then press and hold UP and STOP

together for 5 seconds to save the limit.

* Tap the arrow

several times

or hold down if

needed; press

arrow to stop.

Motor Response

Approx. 5

Approx. 6

If the window treatment direction

needs to be reversed; press and

hold the UP and DOWN together

for 5 seconds until the motor Jogs.

* Reversing

motor direction

using this

method is only

possible during

initial set up.

Motor Response

Approx. 5

Press UP or DOWN to check the

motor direction. If correct, skip to

step 5 of setting the upper limit.

ALL

DISABLE LIMIT SETTING FUNCTION OF REMOTE

This mode is intended to be used after all window treatment programming is completed.

User Mode will prevent accidental or unintended changing of limits.

IMPORTANT

Push LOCK button to lock or

unlocked position

Pressing the LOCK button for 6

seconds will toggle between locked and

unlocked LED show solid or ﬂashing.

LED solid on when locked

LED blinking when unlocked

ALL

SET A FAVORITE POSITION

Move window treatment to

desired position by pressing

UP or DOWN on the remote.

Press P2 on the controller.

Press STOP on

the controller.

Press STOP again

on the controller.

Motor Response Motor Response Motor Response

A = Existing button or channel (to keep). B = Button or channel to add or remove.

USING PRE-EXISTING CONTROLLER

Select the channel (5)

you want to transfer.

Press P2 on existing remote.

Press P2 a second time on

existing remote.

Press the channel (1)

on new remote.

Motor ResponseMotor ResponseMotor Response

ADDING OR REMOVING CONTROLLERS &

CREATING GROUP CHANNELS

USING MOTOR P1 BUTTON

Hold P1 button on motor head. Hold STOP on switch.

Motor Response

Approx. Approx.

Motor Response

* Internal Tubular

pictured. Refer to

P1 LOCATIONS to right

for speciﬁc devices.

P1 LOCATIONS

Drapery

Large Tubular

ALL

Inhaltsverzeichnis

Andere Rowley Fernbedienung Handbücher

Rowley

Rowley R-TEC AUTOMATION RTMHR1C Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung