RST Milo Fire Table Bedienungsanleitung
WARNING:For outdoor use only (domestic)
WARNING: Improper installation, adjustment, alteration, service
or maintenance can cause injury or property damage. Read the
installation, operating, and maintenance instructions thoroughly
before installing or servicing this equipment.
WARNING
Do not store or use gasoline, or other
ammable vapors and liquids, in the
vicinity of this or any other appliance.
A LP-cylinder not connected for use shall
not be stored in the vicinity of this or any
other appliance.
DANGER If you smell gas:
1. Shut o gas to the appliance
2. Extinguish any open ame
3. If odor continues, keep away from
the appliance and immediately call
your gas supplier or re department.
WARNING
Chemicals known to the State of
California to cause cancer, birth defects,
or other reproductive harm are created
by the combustion of propane.
WARNING
Byproducts of the combustion of
propane contain chemicals known to
the State of California to cause cancer
or other reproductive harm.
DANGER CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide which
has no odor. Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such as
a camper, tent, car, or home.
36"x 58"
Fire Table
1
36"x 58"Fire Table
ASSEMBLY INSTRUCTIONS
IMPORTANT, RETAIN FOR FUTURE REFERENCE.
READ CAREFULLY.
2
PARTS LIST
NO. PICTURE PART DESCRIPTION QTY.
A Table base 1
B Table top 1
C Burner tray 1
D Buttery bolt (M8) 4
E Table glass shield 4
F Glass connector clips 4
G Glass screws 8
H 10kgs re glass 1
I Burner lid 1
J Lock washer 4
K Spring washer (M8) 4
3
Step 1. TABLE TOP ASSEMBLY - Attach the re table top (B) to the base (A) by
securing with the bolts (D) and the washers (K + J)
Step 2. BURNER TRAY ASSEMBLY - Lower the burner tray (C) into the rectangular
opening in the re table top (B).
4
Step 3.
GLASS WINDSHIELD ASSEMBLY INSTRUCTIONS
1. Pin the glass clips (F) to the location holes on the table top rst.
2. Then, insert one piece of glass (E) to one side of the clips and fasten with screws (G).
3. Insert another piece of glass (E) to the neighbor side of the clips, fasten with the
screws (G) again.
4. Finally, assemble the balance 2 pieces of the glasses in the same way.
Step 4. ADD GLASS MEDIA - Pour glass media (H) into the burner tray. Take care
not to add more than ½ inch of media over the ame element.
WARNING !
Don’t cover the
gas collector cover
5
Step 5. PROPANE TANK ATTACHMENT - Attach the LP hose from the burner tray
to the LP tank (not included). The marked cylinder LPG capacity is 20 lbs. As
stated by the cylinder manufacturers.
Step 6.
PREPARE FOR LIGHTING - Place a AA battery (not included) in the LP
Valve/Starter Panel before trying to ignite.
CAUTION: Before igniting, turn the valve on the LP tank. Apply soap water
onto all of the leaking components. If bubbles appear, tighten it and apply
soap water again. If no bubbles appear, turn o the valve and proceed to
ignite. If there are still bubbles, please contact RST Brands.
6
Step 7.
LIGHTING INSTRUCTIONS - Make sure the propane tank valve is open before
proceeding. Improper lighting procedures may cause potential consequences.
1. To ignite, push the regulator knob forward and turn one quarter turn
counter clockwise to the “low” position.
2. With the valve depressed, push the igniter button to make the pilot
burner re. Once the pilot burner is red, hold down the valve for over
ten seconds to prevent the pilot burner ame from extinguishing, then
release it.
3. To lower the ame once red, turn the valve without pushing it. To
increase the ame, push the valve in and turn it counter clockwise toward
the high re. If the ame is not in a stable condition (making noise, ame
swaying, etc.), please turn it o immediately
7
Step 8.
SHUTTING OFF THE FIRE TABLE - To shut o, close the valve at the
propane tank taking care to ensure the ame is completely extinguished.
Push the regulator valve in and turn to the o position. Allow 5-minutes of
complete shut o before the appliance is reignited.
Step 9. COVER BURNER - Use lid (I) to cover the burner when not in use. Note: the
cover must be removed when the burner is in operation.
8
CARE AND MAINTENANCE
METAL FRAME MAINTENANCE
Furniture incorporates metal frames, which are design to require minimum
maintenance.
• Metal frames should be kept clean.
• Do not let dirt build up on the metal surfaces.
• Cleaning with mild soap and water is all that is required.
• Never leave furniture in standing water.
• To keep your furniture looking it’s best, you may wish to store or cover your
furniture when not in use for an extended period of time.
NATURAL AND FAUX STONE TOPS
All natural stone table tops, including tumbled marble, polished marble and granite,
are treated at the factory with an impregnating sealer that penetrates deep into the
porous surface providing a long lasting barrier that locks out oils, water, stains and
dirt.
• Spills should be wiped up quickly to avoid any staining on the surface. Regular
cleaning with mild soap and water with a sponge or soft scrub brush is all that
is required.
• Regular residential use should not require resealing for at least 2 to 4 years.
• Natural stone tops will fade in direct sunlight over time. This fading is a natural
process and will be more noticeable on brightly colored stones and polished
marble.
• Stone tops may be re-polished professionally, and always require resealing after
polishing.
• Storing or covering your natural stone top when not in use for extended periods
of time is recommended.
9
FIRE PIT OWNERS MANUAL
Important: Read these instructions carefully before starting installation of the
outdoor re table.
Operation Checklist
For a safe and pleasurable heating experience, perform this check before each use:
Before operating, conrm:
1. I am familiar with the entire owner’s manual and understand all precautions noted.
2. All components are properly assembled, intact, and operable.
3. No alterations have been made.
4. All gas connections are secure and do not leak.
5. Wind velocity is below 10 mph.
6. Unit will operate at reduced eciency below 40 F/ 4 C
7. Fire pit is outdoors and outside of any enclosure.
8. There is adequate fresh air ventilation. Do not use this appliance is any part has been
under water. Immediately call a qualied service technician to inspect the appliance and to
replace any part of the control system and gas control which has been under water.
9. Fire pit is away from gasoline or other ammable liquids or vapors.
10. Fire pit is away from windows, air intake openings, sprinklers, and other water sources.
11. Fire pit is at least 36 inches on rear and at least 36 inches on sides from combustible
materials.
12. Fire pit is on a hard and level surface.
13. There are no signs of spider or insect nests.
14. All burner passages are clear.
15. All air circulation passages are clear.
Warnings:
1. Children and adults should be alerted to the hazards of high surface temperatures and
should stay away to avoid burns or clothing ignition.
2. Young children should be carefully supervised when they are in the area of the re pit.
3. Clothing or other protective material should not be hung from the re pit, or placed on or
near the re pit.
4. Any guard or protective device removed for servicing the re pit must be replaced prior to
operating the re pit.
5. Installation and repair should be done by a qualied service person. The re pit should be
inspected before use and at least annually by a qualied service person.
6. More frequent cleaning may be required as necessary. It is imperative that control
compartment, burner, and circulating air passageways of the re pit be kept clean.
After operation:
1. Gas control is in the OFF position.
2. Gas tank valve is turned OFF.
3. Disconnect the gas line.
4. After each use, replace the cap on the tank.
Before beginning assembly, make sure all parts are present. Compare parts with the package
contents list and hardware contents above. If any part is missing or damaged, do not attempt to
assemble the product. Contact customer service for replacement parts.
Important: for safe operation and proper performance of this product and to comply with
certication, listings, and building code acceptances, use only our controls, parts, and accessories
that have been specically listed for use with this burner system. Use of other controls, parts, or
accessories is prohibited and will void all warranties, certications, listings, and building code
approvals, and may cause property damage, personal injury, and loss of life.
Inhaltsverzeichnis
Andere RST Außenkamin Handbücher
