RTA 460ECPS-N700 Technisches Datenblatt

Real Time Automation, Inc.

1-800-249-1612

Firmware Version 8.4.6

460ECPS-N700

Protocol Gateway

Product User Guide

Real Time Automation, Inc.

1-800-249-1612

Trademarks

CompactLogix, ControlLogix, & PLC-5 are registered trademarks of Rockwell Automation, Inc. EtherNet/IP is a trademark of the ODVA.

MicroLogix, RSLogix 500, and SLC are trademarks of Rockwell Automation, Inc. Microsoft, Windows, and Internet Explorer are registered

trademarks of Microsoft Corporation. BACnet®is a registered trademark of American Society of Heating, Refrigerating and Air-Conditioning

Engineers (ASHRAE). All other trademarks and registered trademarks are the property of their holders.

Limited Warranty

Real Time Automation, Inc. warrants that this product is free from defects and functions properly.

EXCEPT AS SPECIFICALLY SET FORTH ABOVE, REAL TIME AUTOMATION, INC. DISCLAIMS ALL OTHER WARRANTIES, BOTH

EXPRESSED AND IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR APPLICATION. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER

RIGHTS, WHICH VARY FROM STATE TO STATE.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements

associated with any particular application, Real Time Automation, Inc. cannot assume responsibility or liability for actual use based on the

examples and diagrams. Except as specifically set forth above, Real Time Automation and its distributors and dealers will in no event be liable

for any damages whatsoever, either direct or indirect, including but not limited to loss of business profits, income, or use of data. Some states

do not allow exclusion or limitation of incidental or consequential damages; therefore, the limitations set forth in this agreement may not apply

to you.

No patent liability is assumed by Real Time Automation with respect to use of information, circuits, equipment, or software described in this

manual.

Government End-Users

If this software is acquired by or on behalf of a unit or agency of the United States Government, this provision applies: The software (a) was

developed at private expense, is existing computer software, and was not developed with government funds; (b) is a trade secret of Real Time

Automation, Inc. for all purposes of the Freedom of Information Act; (c) is “restricted computer software” submitted with restricted rights in

accordance with subparagraphs (a) through (d) of the Commercial “Computer Software-Restricted Rights” clause at 52.227-19 and its

successors; (d) in all respects is proprietary data belonging solely to Real Time Automation, Inc.; (e) is unpublished and all rights are reserved

under copyright laws of the United States. For units of the Department of Defense (DoD), this software is licensed only with “Restricted Rights”:

as that term is defined in the DoD Supplement of the Federal Acquisition Regulation 52.227-7013 (c) (1) (ii), rights in Technical Data and

Computer Software and its successors, and: Use, duplication, or disclosures is subject to restrictions as set forth in subdivision (c) (1) (ii) of the

Rights in Technical Data and Computer Software clause at 52.227-7013. If this software was acquired under GSA schedule, the U.S.

Government has agreed to refrain from changing or removing any insignia or lettering from the Software or documentation that is provided or

from producing copies of the manual or media. Real Time Automation, Inc.

 
 
Real Time Automation, Inc. 
3 
1-800-249-1612 
 
 
Revision History ............................................................................................................................................ 5 
Overview ....................................................................................................................................................... 6 
Hardware Platforms...................................................................................................................................... 7 
Hardware –N700 .......................................................................................................................................... 8 
Powering the Gateway.............................................................................................................................. 8 
Mounting with a DIN Rail.............................................................................................................................. 9 
Installing.................................................................................................................................................... 9 
Removing .................................................................................................................................................. 9 
Accessing the Main Page............................................................................................................................. 10 
Error: Main Page Does Not Launch .........................................................................................................11 
Committing Changes to the Settings ..........................................................................................................12 
Main Page ................................................................................................................................................... 13 
Device Configuration...................................................................................................................................14 
Network Configuration ............................................................................................................................... 15 
EtherNet/IP Scanner Configuration ............................................................................................................ 16 
EtherNet/IP Scanner Device Configuration.................................................................................................17 
Configuring Input Instance...................................................................................................................... 18 
Configuring Output Instance................................................................................................................... 19 
Configuring Input and Output Instances (cont.) ..................................................................................... 20 
PROFINET IO Server Configuration .............................................................................................................21 
PROFINET IO Server Slot Configuration ......................................................................................................22 
PROFINET IO Server Slot Configuration: Auto-Configure........................................................................23 
Auto-Configure Group by Device vs. Auto-Configure Group by Data Type............................................ 24 
Group by Device (Default Method)..................................................................................................... 24 
Group by Data Type ............................................................................................................................ 24 
PROFINET IO Server Slot Configuration: Manual Mode.......................................................................... 25 
Example Setup......................................................................................................................................... 26 
Setting up the PLC- Example Using Simatic Step 7 software ......................................................................27 
Setting up the PLC- Example Using TIA Portal ............................................................................................33 
Mapping - Transferring Data Between Devices .......................................................................................... 40 
Display Mapping and Values.......................................................................................................................41 
Display Data ............................................................................................................................................ 41 
Display String...........................................................................................................................................43 
Data and String Mapping –Auto-Configure................................................................................................44 

 
 
Real Time Automation, Inc. 
4 
1-800-249-1612 
 
 
Data Mapping –Explanation.......................................................................................................................45 
Data Mapping –Adding Diagnostic Information ........................................................................................46 
String Mapping –Explanation.....................................................................................................................49 
Mapping –Auto-Configure Mode to Manual Configure Mode .................................................................. 50 
Mapping –Manual Configure Mode to Auto-Configure Mode .................................................................. 51 
View as Text ................................................................................................................................................ 52 
Data Mapping.......................................................................................................................................... 52 
String Mapping........................................................................................................................................ 52 
Security Configuration ................................................................................................................................ 53 
Security Configuration-Security Levels ................................................................................................... 54 
Security - Log In.......................................................................................................................................55 
Security - Log Out.................................................................................................................................... 56 
Email Configuration .................................................................................................................................... 57 
Alarm Configuration.................................................................................................................................... 58 
Diagnostics –Alarm Status...................................................................................................................... 60 
Alarms –Active .......................................................................................................................................60 
Alarms –Clear ......................................................................................................................................... 61 
Change of State (COS) Configuration..........................................................................................................62 
Diagnostics Info........................................................................................................................................... 63 
Diagnostics –Data and String Mapping .................................................................................................. 63 
Diagnostics –EtherNet/IP Scanner .............................................................................................................64 
Diagnostics –PROFINET IO Server .............................................................................................................. 67 
Configuration Files ...................................................................................................................................... 69 
Export Configuration............................................................................................................................... 69 
Import Configuration .............................................................................................................................. 69 
Save and Replace Configuration Using SD Card.......................................................................................... 70 
Saving Configuration Using SD Card........................................................................................................ 70 
Replacing Configuration Using SD Card ..................................................................................................70 
Utilities........................................................................................................................................................ 71 
 

Real Time Automation, Inc.

1-800-249-1612

Revision History

Version

Date

Notes

6.3.4

11/13/18

Features Added

1. Released BC Protocol on the N2E Hardware

2. Released PS Protocol on NNA1 Hardware with updated GSDML file

3. Released Base Triggering with ETC Protocol Optimization

Bug Fixes

1. WI Protocol handling of STRING data types

Allow Origins in GET requests, and CR / LF on HTTP 200 responses

2. WI Protocol now has the Allow Origins as part of the HTTP Header

3. WI Protocol receives a second CR / LF at the end of the HTTP 200 response

6.4.7

03/05/19

Features Added

1. New Header Image

2. Released ASCII Protocol on N2E Hardware

3. Released ES Protocol on N2E Hardware

4. Updated Profinet Code and new GSDML V2.3 on NNA1 Hardware

Bug Fixes

1. Cleaned up ASCII parser and concatenation functionality

8.3.9

10/21/2019

Features Added

1. Released BACnet MS/TP Slave Protocol on N2E Hardware

2. Released Profinet on N2E Hardware

3.Updated GSMDL file with new icons

4. Released S7 protocol

5. Released Wi-Fi Hardware

Bug Fixes

1.Improved functionality of the Network conifguration page when going from Independent

to Switch Mode.

2. Import/Export issues

8.4.5

11/18/2019

Features Added

1. Released OPC UA Server (US) Protocol

2. Ability to now Import/Export Template Files with out an FTP session.

Bug Fixes

1. Updated Profinet Server (PS) on N34 hardware Platform

2. Updated Wi-Fi software

Real Time Automation, Inc.

1-800-249-1612

Overview

The 460ECPS-N700 gateway connects up to 32 EtherNet/IP Adapters with a PROFINET IO Controller. By

following this guide, you will be able to configure the 460ECPS-N700 gateway.

For further customization and advanced use, please reference the appendices located on the CD or

online at: http://www.rtautomation.com/product/460-gateway-support/.

If at any time you need further assistance do not hesitate to call Real Time Automation support.

Support Hours are Monday-Friday 8am-5pm CST

Toll free: 1-800-249-1612

Email: support@rtautomation.com

Real Time Automation, Inc.

1-800-249-1612

Hardware Platforms

The 460 Product Line supports a number of different hardware platforms. There are differences in how

they are powered, what serial settings are supported, and some diagnostic features supported (such as

LEDs). For these sections, be sure to identify the hardware platform you are using.

To find which hardware platform you are using:

1) Look on the front or back label of the unit for the part number.

2) On the webpage inside the gateway, navigate to the dropdown menu under Other and select

Utilities. Click the Listing of Revisions button. The full part number is displayed here.

Once you have the full part number, the platform will be the number following the “-N”:

Real Time Automation, Inc.

1-800-249-1612

Hardware –N700

Powering the Gateway

•Connect an 12-24 VDC power source to the gateway:

Use Barrel Connector with Center (+) Outer Shell (-) OR

2-Pin Terminal power connection with Red Wire = (+) Black Wire = (-) NOT BOTH

Real Time Automation, Inc.

1-800-249-1612

Mounting with a DIN Rail

Installing

Follow these steps to install your interface converter.

1) Mount your DIN Rail.

2) Hook the bottom mounting flange under the DIN Rail.

3) While pressing the 460ECPS-N700 against the rail, press up to engage the spring loaded lower

clip and rotate the unit parallel to the DIN Rail.

4) Release upward pressure.

Removing

Follow these steps to remove your interface converter.

1) Press up on unit to engage the spring loaded lower clip.

2) Swing top of the unit away from DIN Rail.

DIN Rail

Spring Loaded Lower Clip

Real Time Automation, Inc.

1-800-249-1612

Accessing the Main Page

The following steps will help you access the browser based configuration of the gateway. By default,

DHCP is enabled. If the gateway fails to obtain an IP address over DHCP it will Auto IP with 169.254.X.Y.

For more information on your Operating system network setting refer to the Access Browser

Configuration Doc on the CD or download from our support web site.

1) Insert the provided CD-ROM into a computer also on the network.

2) Run the IPSetup.exe program from the CD-ROM.

3) Find unit under “Select a Unit”.

a. Change Gateway’s IP address to match that of your PC if DHCP has failed.

i. You will know DHCP has failed if the gateway’s IP address is AutoIP at

169.254.X.Y.

ii. If successful, it will say DHCP’d at ex: 192.168.0.100 or however your DCHP

Client is set up.

b. If you do not see the gateway in this tool, then your PC is most likely set up as a static IP.

i. Change your PC’s network settings to be DHCP. If DHCP fails, then it will change

to be on the 169.254.x.y network.

ii. Relaunch the IP Setup tool to see if gateway can be discovered now.

4) Click Launch Webpage. The Main page should appear.

Default setting is set to DHCP. If DHCP fails, default IP Address is 169.254.x.y

Inhaltsverzeichnis

Andere RTA Tor Handbücher

RTA

RTA 460BSTCP-N2E Technisches Datenblatt

RTA

RTA 460ETCMM-NNA4 Technisches Datenblatt

RTA

RTA 460AUSB-N70U Technisches Datenblatt

RTA

RTA 460MRSQT-NNA4 Technisches Datenblatt

RTA

RTA 460ETCMM-N2EW Technisches Datenblatt

RTA

RTA 460ECBMS-NNA4 Technisches Datenblatt

RTA

RTA 460ETCBM-NNA1-D Technisches Datenblatt

RTA

RTA 460ECBM-NNA1 Technisches Datenblatt

RTA

RTA 460ETCMS-N700 Technisches Datenblatt

RTA

RTA 460PSMM-N700 Technisches Datenblatt

RTA

RTA 460TCPUS-NNA1 Technisches Datenblatt

RTA

RTA 460ETCBS-NNA4 Technisches Datenblatt

RTA

RTA 460ECETC-NNA4 Technisches Datenblatt

RTA

RTA 460ECPS-N34 Technisches Datenblatt

RTA

RTA 460MCWI-N2EW Technisches Datenblatt

RTA

RTA 460BSTCP-NNA4 Technisches Datenblatt

RTA

RTA 460ECBM-N700 Technisches Datenblatt

RTA

RTA 460MSPBS-N70PB Technisches Datenblatt

RTA

RTA 460PSDFM-NNA1 Technisches Datenblatt

RTA

RTA 460ECPBS-N70PB Technisches Datenblatt

RTA

RTA 460BC-NNA1 Technisches Datenblatt

RTA

RTA 460ESPS-NNA4 Technisches Datenblatt

RTA

RTA 460BMDFM-N34 Technisches Datenblatt

RTA

RTA 460PSUSB-NNCU Technisches Datenblatt

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung

Rosonix Technology

Rosonix Technology RSG-3000 Bedienungsanleitung