RTA 460ESPBS-N70PB Technisches Datenblatt
Real Time Automation, Inc.
1
1-800-249-1612
Firmware Version 8.7.4
460ESPBS-N70PB
Protocol Gateway
Product User Guide
Real Time Automation, Inc.
2
1-800-249-1612
Trademarks
CompactLogix, ControlLogix, & PLC-5 are registered trademarks of Rockwell Automation, Inc. EtherNet/IP is a trademark of the ODVA.
MicroLogix, RSLogix 500, and SLC are trademarks of Rockwell Automation, Inc. Microsoft, Windows, and Internet Explorer are registered
trademarks of Microsoft Corporation. BACnet®is a registered trademark of American Society of Heating, Refrigerating and Air-Conditioning
Engineers (ASHRAE). All other trademarks and registered trademarks are the property of their holders.
Limited Warranty
Real Time Automation, Inc. warrants that this product is free from defects and functions properly.
EXCEPT AS SPECIFICALLY SET FORTH ABOVE, REAL TIME AUTOMATION, INC. DISCLAIMS ALL OTHER WARRANTIES, BOTH
EXPRESSED AND IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR APPLICATION. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER
RIGHTS, WHICH VARY FROM STATE TO STATE.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements
associated with any particular application, Real Time Automation, Inc. cannot assume responsibility or liability for actual use based on the
examples and diagrams. Except as specifically set forth above, Real Time Automation and its distributors and dealers will in no event be liable
for any damages whatsoever, either direct or indirect, including but not limited to loss of business profits, income, or use of data. Some states
do not allow exclusion or limitation of incidental or consequential damages; therefore, the limitations set forth in this agreement may not apply
to you.
No patent liability is assumed by Real Time Automation with respect to use of information, circuits, equipment, or software described in this
manual.
Government End-Users
If this software is acquired by or on behalf of a unit or agency of the United States Government, this provision applies: The software (a) was
developed at private expense, is existing computer software, and was not developed with government funds; (b) is a trade secret of Real Time
Automation, Inc. for all purposes of the Freedom of Information Act; (c) is “restricted computer software” submitted with restricted rights in
accordance with subparagraphs (a) through (d) of the Commercial “Computer Software-Restricted Rights” clause at 52.227-19 and its
successors; (d) in all respects is proprietary data belonging solely to Real Time Automation, Inc.; (e) is unpublished and all rights are reserved
under copyright laws of the United States. For units of the Department of Defense (DoD), this software is licensed only with “Restricted Rights”:
as that term is defined in the DoD Supplement of the Federal Acquisition Regulation 52.227-7013 (c) (1) (ii), rights in Technical Data and
Computer Software and its successors, and: Use, duplication, or disclosures is subject to restrictions as set forth in subdivision (c) (1) (ii) of the
Rights in Technical Data and Computer Software clause at 52.227-7013. If this software was acquired under GSA schedule, the U.S.
Government has agreed to refrain from changing or removing any insignia or lettering from the Software or documentation that is provided or
from producing copies of the manual or media. Real Time Automation, Inc.
© 2020 Real Time Automation, Inc. All rights reserved.
Real Time Automation, Inc.
3
1-800-249-1612
Revision History ............................................................................................................................................6
Overview .......................................................................................................................................................7
Hardware Platforms......................................................................................................................................8
Hardware –N70PB.................................................................................................................................... 9
Powering the Gateway..............................................................................................................................9
Port Configuration...................................................................................................................................10
Mounting with a DIN Rail............................................................................................................................11
Installing..................................................................................................................................................11
Removing ................................................................................................................................................11
Accessing the Main Page.............................................................................................................................12
Error: Main Page Does Not Launch.........................................................................................................13
Committing Changes to the Settings ..........................................................................................................14
Main Page ...................................................................................................................................................15
Device Configuration...................................................................................................................................16
Network Configuration ...............................................................................................................................17
EtherNet/IP Adapter Configuration ............................................................................................................18
EtherNet/IP Adapter Data Group Configuration.........................................................................................19
EtherNet/IP Adapter Data Group Configuration: Auto-Configure..........................................................20
Group by Device (Default Method).........................................................................................................21
Group by Data Type ................................................................................................................................21
EtherNet/IP Adapter Data Group Configuration: Manual Mode............................................................22
EtherNet/IP Adapter Data Group Configuration: Using Strings..............................................................24
EtherNet/IP Adapter Mapping Configuration.........................................................................................27
PROFIBUS Slave Configuration....................................................................................................................30
PROFIBUS Slave Configuration....................................................................................................................31
PROFIBUS Slave Slot Configuration: Auto-Server Mode (Default)..........................................................32
Auto-Configure Group by Device vs. Auto-Configure Group by Data Type............................................33
Group by Device (Default Method).........................................................................................................33
Group by Data Type ................................................................................................................................33
PROFIBUS Slave Slot Configuration: Manual Mode................................................................................34
Setting up the PLC- Example Using Simatic Classic Step 7..........................................................................35
Setting up the PLC- Example Using TIA Portal ............................................................................................39
Mapping - Transferring Data Between Devices ..........................................................................................44
Display Mapping and Values.......................................................................................................................45
Real Time Automation, Inc.
4
1-800-249-1612
Display Data ............................................................................................................................................45
Display String...........................................................................................................................................48
Display String use case................................................................................................................................50
Data and String Mapping –Auto-Configure................................................................................................51
Data Mapping –Explanation.......................................................................................................................52
Data Mapping –Adding Diagnostic Information ........................................................................................53
String Mapping –Explanation.....................................................................................................................57
Mapping –Auto-Configure Mode to Manual Configure Mode ..................................................................58
Mapping –Manual Configure Mode to Auto-Configure Mode ..................................................................59
View as Text ................................................................................................................................................60
Data Mapping..........................................................................................................................................60
String Mapping........................................................................................................................................60
Base Triggering –Data Validiation Triggering.........................................................................................61
Security Configuration ................................................................................................................................63
Security Configuration-Security Levels ...................................................................................................64
Security - Log In.......................................................................................................................................65
Security - Log Out....................................................................................................................................65
Email Configuration ....................................................................................................................................66
Alarm Configuration....................................................................................................................................67
Diagnostics –Alarm Status......................................................................................................................69
Alarms –Active .......................................................................................................................................69
Alarms –Clear .........................................................................................................................................70
Change of State (COS) Configuration..........................................................................................................71
Diagnostics Info...........................................................................................................................................72
Diagnostics Mapping...............................................................................................................................72
Diagnostics –EtherNet/IP Adapter.............................................................................................................73
Diagnostics –PROFIBUS Slave.....................................................................................................................76
LED Configuration .......................................................................................................................................78
Configuration Files ......................................................................................................................................79
Export Configuration...............................................................................................................................79
Import Configuration ..............................................................................................................................79
Save and Replace Configuration Using SD Card..........................................................................................81
Saving Configuration Using SD Card........................................................................................................81
Replacing Configuration Using SD Card ..................................................................................................81
Real Time Automation, Inc.
6
1-800-249-1612
Revision History
Version
Date
Notes
8.3.9
10/21/2019
Features Added
1. Released BACnet MS/TP Slave Protocol on N2E Hardware
2. Released Profinet on N2E Hardware
3.Updated GSMDL file with new icons
4. Released S7 protocol
5. Released Wi-Fi Hardware
Bug Fixes
1.Improved functionality of the Network conifguration page when going from Independent
to Switch Mode.
2. Import/Export issues
8.4.5
11/18/2019
Features Added
1. Released OPC UA Server (US) Protocol
2. Ability to now Import/Export Template Files with out an FTP session.
Bug Fixes
1. Updated Profinet Server (PS) on N34 hardware Platform
2. Updated Wi-Fi software
8.6.0
2/28/20
Bug Fixes
1. Omron Plc Communication fixes for EtherNet/IP
2. Profinet GSDML Substitute values fix
8.7.4
9/1/20
Features Added:
1. BMS, BM, DFM, DS, DM, TCP, USB, PBS have been ported to the latest base software.
2. TCP,BMS,BM now Available on N2E and N2EW hardware Platform
3. New ASCII Mode Available on TCP/A/USB/WI protocols
4. User Guides updated with more examples
Bug Fixes:
1. Improved Data Mapping and String Mapping performance
2. Improved functionality/performance on EC,ETC,ES,MC,MS,BS,BC, A,,WI,PS protocols.
Real Time Automation, Inc.
7
1-800-249-1612
Overview
The 460ESPBS-N70PB gateway connects an EtherNet/IP Scanner with a Profibus DP Controller. By
following this guide, you will be able to configure the 460ESPBS-N70PB gateway.
For further customization and advanced use, please reference the appendices located on the CD or
online at: http://www.rtautomation.com/product/460-gateway-support/.
If at any time you need further assistance, do not hesitate to call Real Time Automation support.
Support Hours are Monday-Friday 8am-5pm CST
Toll free: 1-800-249-1612
Email: support@rtautomation.com
Real Time Automation, Inc.
8
1-800-249-1612
Hardware Platforms
The 460 Product Line supports a number of different hardware platforms. There are differences in how
they are powered, what serial settings are supported, and some diagnostic features supported (such as
LEDs). For these sections, be sure to identify the hardware platform you are using.
To find which hardware platform you are using:
1) Look on the front or back label of the unit for the part number.
2) On the webpage inside the gateway, navigate to the dropdown menu under Other and select
Utilities. Click the Listing of Revisions button. The full part number is displayed here.
Once you have the full part number, the platform will be the number following the “-N”:
Real Time Automation, Inc.
9
1-800-249-1612
Hardware –N70PB
Powering the Gateway
1) Connect a 12-24 VDC power source to the gateway:
a) Use Barrel Connector with Center (+) Outer Shell (-) OR
b) 2-Pin Terminal power connection with Red Wire = (+) Black Wire = (-) NOT BOTH
Real Time Automation, Inc.
10
1-800-249-1612
Port Configuration
The Port Configuration page is where you set port specific parameters. These settings must match the
settings of the device(s) that you are connecting to.
When you have completed your port configuration, click the Save Parameters button.
Note: The PROFIBUS port is NOT configurable. The only configuration that the PROFIBUS port requires is
the Slave Address on the PROFIBUS Slave Configuration page.
Inhaltsverzeichnis
Andere RTA Tor Handbücher
RTA
RTA 460ETCWI-NNA1 Technisches Datenblatt
RTA
RTA 460ETCUS-N2EW Technisches Datenblatt
RTA
RTA 460ESPS-N2E Technisches Datenblatt
RTA
RTA 460MCA-N700 Technisches Datenblatt
RTA
RTA 460ETCBM-N700 Technisches Datenblatt
RTA
RTA 460ETCWI-N2E Technisches Datenblatt
RTA
RTA 460ESMRS-N700 Technisches Datenblatt
RTA
RTA 460BSUSB-NNCU Technisches Datenblatt
RTA
RTA 460MMBS-NNA1 Technisches Datenblatt
RTA
RTA 460ESBC-NNA4 Technisches Datenblatt
RTA
RTA 460ETCBS-NNA4 Technisches Datenblatt
RTA
RTA 460ECQT-NNA1 Technisches Datenblatt
RTA
RTA 460MSMM-N2E Technisches Datenblatt
RTA
RTA 460ETCMS-N2EW Technisches Datenblatt
RTA
RTA 460ASC-N2E Technisches Datenblatt
RTA
RTA 460ECTCP-NNA4 Technisches Datenblatt
RTA
RTA 460ETCPS-N2E Bedienungsanleitung
RTA
RTA 460MMBS-N2EW Technisches Datenblatt
RTA
RTA 460MSBM-NNA1 Technisches Datenblatt
RTA
RTA 460TCPA-N2EW Technisches Datenblatt
Beliebte Tor Handbücher anderer Marken
LST
LST M500RFE-AS Bedienungsanleitung
Kinnex
Kinnex Media Gateway Bedienungsanleitung
2N Telekomunikace
2N Telekomunikace 2N StarGate Bedienungsanleitung
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung
Telsey
Telsey CPVA 500 - SIP Bedienungsanleitung
HMS
HMS Netbiter EasyConnect EC150 Bedienungsanleitung
Huawei
Huawei EchoLife HG620 Bedienungsanleitung
AT&T
AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch
Logic IO
Logic IO RTCU MX2 turbo Bedienungsanleitung
Suttle
Suttle MediaMAX MXM-521 Bedienungsanleitung
Rosonix Technology
Rosonix Technology RSG-3000 Bedienungsanleitung