Rtech TIG200PDC Bedienungsanleitung

www.r-techwelding.co.uk

TIG200PDC DC TIG WELDER

OPERATION INSTRUCTIONS

www.r-techwelding.co.uk

Tel: 01452 733933

Thank you for selecting the R-Tech TIG200PDC Inverter DC Tig Welder.

The TIG200PDC has many benefits over traditional TIG welders, including pulse welding, slope

up/down and an industrial 60% duty cycle.

We want you to take pride in operating our TIG200PDC as much pride as we have taken in

making this product for you. Please read all information in this manual before operation

PLEASE EXAMINE THE CARTON AND EQUIPMENT FOR DAMAGE IMMEDIATELY

When this equipment is shipped, title passes to the purchaser upon receipt from the courier.

Consequently all claims for material damaged in shipment must be made by purchaser against

the transportation company used.

Please record your equipment identification below for future reference. This information can be

found on the data plate at rear of machine.

Product: TIG200PDC

Serial No. ___________________________________

Date of Purchase _____________________________

Where Purchased _____________________________

Whenever you request replacement parts or information on this equipment please always

supply information you have recorded above.

This product is covered by a 2 year parts and labour warranty; we will cover cost of collecting and

returning the item to you. External items, (torch, earth lead etc…) are covered by a 3 month warranty. Any

faults/damage found caused by a customer will be charged accordingly.

Pay particular attention to the safety instructions we have provided you for your protection

The level of seriousness to be applied to each section is explained below

WARNING

This statement appears where the information must be followed exactly to avoid serious personal injury.

CAUTION

This statement appears where the information must be following to avoid a minor personal injury or damage

to this equipment.

Introduction

The R-Tech TIG200PDC is a member of our field acclaimed family of welding products.

Premium features include:-

1 Inverter power source - more efficient to operate, provides smoother weld characteristics.

2 Pulse welding in DC Tig welding mode

3 HF Arc start - Easy arc striking and prolonged tungsten life

4 Slope up / slope down

5 Digital amp meter

℃

6 Industrial 60% Duty cycle at 200 Amps @ 40

Recommended Processes

The R-Tech TIG200PDC is recommended for the Tig welding processes within its output capacity of 200 Amps

Equipment Limitations

The R-Tech TIG200PDC is protected from overloads beyond the output ratings and duty cycle as per machine

specifications with thermostat protection of the output coils and rectifiers.

Welding Capability - Duty Cycle

The R-Tech TIG200PDC is rated at 200 Amps at 60% duty cycle on a ten minute basis. If the duty cycle is

exceeded a thermal protector will shut machine off until the machine cools.

Technical Specifications

Model No. R-Tech TIG200PDC

Input 240V AC 50/60Hz Fuse Slow-blow 32Amp

MMA

No-load Voltage 60V - 80V

Current Range 5A - 160A

Rated Output Current 160A

Duty Cycle 60%

DC TIG

No-load Voltage 60V - 80V

Current Range 5A - 200A

Rated Output Current 200A

Duty Cycle 60%

Up-Slope Time 0-5 Seconds

Down-Slope Time 0-5 Seconds

Pulse Frequency Range 0.5Hz - 25Hz

Gas Post Flow Time 1 - 10 Seconds

Arc Starting Mode High Frequency

Pulse width 0.1-0.9

Gross Weight 16 KG

Insulation IP21S

Dimensions mm 425 x 195 x 310

Safety Precautions

Read entire section before starting installation

WARNING!

Electric Shock can kill - Only qualified personnel should perform this installation. Turn off input power at the fuse

box before working on this equipment. Do not touch electrically live parts. Always connect the machine to an

earthed mains supply as per national recommended standards.

Select suitable location

Place the welder where clean cooling air can freely circulate in and out of the front & rear louver vents. Dirt, dust

or any foreign material that can be drawn through vents into welder must be kept to a minimum. Failure to

observe these precautions can result in excessive operating temperatures which can lead to plant failure.

Grinding

Do not direct grinding particles towards the welder. An abundance of conductive material can cause plant failure.

Stacking

This machine cannot be stacked.

Transport - Unloading

Never underestimate the weight of equipment, never move or leave suspended in the air above people. Use

recommended lifting equipment at all times.

WARNING!

Falling Equipment can cause injury. Never lift welder with gas bottle attached. Never lift above personnel.

Tilting

Machine must be placed on a secure level surface or on a recommended undercarriage/trolley. This machine may

topple over if this procedure is not followed.

Environmental Rating

The welding power source carries the IP21S rating. It may be used in normal industrial and

commercial environments. Avoid using in areas where water / rain is around.

Read and follow the 'Electric Shock Warnings' in the safety section if welding must be performed

under electrically hazardous conditions such as welding in wet areas or water on the work piece.

Electrical Installation

WARNING!

ELECTRIC SHOCK CAN KILL

Machine grounding and High Frequency Interference Protection

This welder must be grounded to earth. See national electrical codes fro proper grounding methods.

The high frequency generator being similar to a radio transmitter may cause interference to radio, TV

and other electronic equipment. These problems may be the result of radiated interference. Proper

grounding methods can reduce or eliminate this.

Radiated interference can develop in the following ways

1 Direct interference from welder power source

2 Direct interference from the welding leads

3 Direct interference radiated from feedback into power lines

4 Interference from re-radiation by un-grounded metallic objects.

Keeping these contributing factors in mind, installing equipment as per following instructions should

minimize problems.

1 Keep the welder input power lines as short as possible and enclose as much of them as

possible in metal conduit or equivalent shielding. There should be a good electrical contact between

this conduit and ground (Earth).

2 Keep the work and electrode leads as short as possible. Tape the leads together where

practical.

3 Be sure the torch and earth leads rubber coverings are free from cuts and cracks that allow

welding power leakage

4 Keep earth lead connection to work in good condition - Clean area on workbench where earth

clamp is situated on a regular basis.

Input Connections

Make sure the voltage, phase and frequency of input power is as specified on machine rating plate

located at rear of machine.Have a qualified electrician provide suitable input power as per national

electrical codes. Makesure machine is earthed / grounded.

Make sure fuse or circuit breaker is correct rating for machine. Using fuses or circuit breakers smaller

than recommended will result in 'nuisance' shut off from welder inrush currents even if welding at low

amperages.

Failure to follow these instructions can cause immediate failure within the welder and void machines

warranty.

Turn the input power OFF at the mains switch & fuse box before working on this equipment.

Have a qualified electrician install & service this equipment.

Allow machine to sit for 5 minutes minimum to allow the power capacitors to discharge before

working inside this equipment. Do not touch electrically live parts

The TIG200PDC Inverter Tig Welder requires a 240V 50/60Hz 32amp fused supply.

It comes with a 3 metre mains cable attached.

Connect wires according to national coding.

Brown wire - Live

Blue wire - Neutral

Green/Yellow Wire - Earth (Ground)

Connecting to an Engine Driven Generator

If connecting this machine to an engine driven generator please ensure

the following

Minimum Generator KVA Output - 7.5 KVA

continuous Generator to be fitted with AVR (automatic voltage regulation)

DO NOT USE ON A GENERATOR WITHOUT AVR

Connecting to a generator without the above minimum requirements will

invalidate your warranty.

Connections for TIG200PDC Rear machine connections

Fig 1

1 Mains input cable

Fit required plug as per your electrical installation

2 On/Off Switch

3 Gas input connector

Connect input gas hose ensuring connection is tight

4 Earth for chassis

If experiencing localized interference when using machine, connect workbench to this point using

correct graded earth wire (not normally used)

1x110V or 240V

Connections for TIG (GTAW) Welding

Fig 2

1 Negative power connector

connect Tig Torch Dinze to power connector by inserting and twisting until tight

2 Gas outlet

Connect the torch gas hose

3 Positive power connector +

Connect the earth lead to by inserting and twisting until tight and the earth clamp to work/

bench

4. Torch control socket 7-Pin

Connect torch control plug

To avoid a High Frequency shock keep the Tig torch in good condition and replace if any of the

insulation is damaged.

Connect the gas input hose to gas regulator and use 'Pure Argon' Gas, available from local suppliers.

Set gas flow/pressure to 8-12 LPM.

Make sure gas bottle is secured to avoid injury.

Connections for STICK MMA (SMAW) Welding

Fig 3

1. Negative power connector

Connect the earth lead to by inserting and twisting until tight and the earth clamp to work/bench.

2. Gas Outlet - NOT used in MMA mode

3. Positive power connector +

Connect the electrode holder by inserting and twisting until tight

4. Torch switch plug - Not used in MMA mode

Inhaltsverzeichnis

Andere Rtech Schweißsystem Handbücher

Rtech

Rtech TIG160PDC Bedienungsanleitung

Rtech

Rtech MIG181 Bedienungsanleitung

Rtech

Rtech TIG401 TFT Bedienungsanleitung

Rtech

Rtech TIG200DV-PD Bedienungsanleitung

Rtech

Rtech TIG160PD Bedienungsanleitung

Rtech

Rtech TIG200PD-DV Bedienungsanleitung

Rtech

Rtech TIG171 TFT Bedienungsanleitung

Rtech

Rtech TIG160PDC Bedienungsanleitung

Rtech

Rtech PLASMA 30DV Bedienungsanleitung

Rtech

Rtech TIG180PDC Bedienungsanleitung

Rtech

Rtech INV160 Bedienungsanleitung

Rtech

Rtech TIG200DV Bedienungsanleitung

Rtech

Rtech I-MIG160 MIG Bedienungsanleitung

Rtech

Rtech MTS-450 Bedienungsanleitung

Rtech

Rtech I-CUT100P Bedienungsanleitung

Rtech

Rtech P100HF Bedienungsanleitung

Rtech

Rtech ProArc 135 Bedienungsanleitung

Rtech

Rtech POWER MTS210D Bedienungsanleitung

Rtech

Rtech PLASMA 60HF Bedienungsanleitung

Rtech

Rtech C-MIG 315 Bedienungsanleitung

Rtech

Rtech MMA 160S Bedienungsanleitung

Rtech

Rtech PROArc 175 Bedienungsanleitung

Rtech

Rtech MTS 255HF Bedienungsanleitung

Rtech

Rtech MIG251 Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung