RTS KP-32 Bedienungsanleitung

Installation Guide

CSI-100 Coaxial System Interface

9330-7693-000 Rev A 11/02

STEP 1

The CSI-100 can only be field installed in

KP-32 series equipment if the rear panel has

a knockout provided for the BNC connector

on the CSI-100 board. See Figure 1 for the

location of the knockout. If the knockout is

present, proceed to STEP 2. If the knockout

is not present, the CSI-100 can be installed,

but requires factory level modifications.

Contact RTS for pricing and instructions.

STEP 2

The backpanel and top cover of the keypanel

must be removed in order to install the CSI-

100. Begin by turning the unit over and

remove the three screws along the bottom of

the back panel as shown in Figure 2.

STEP 3

Turn the unit over. Remove the ten screws

that secure the top cover on the unit. See

Figure 3.

STEP 4

Remove the two standoffs on the 9-pin D-

sub connector. You may also need to remove

additional screws from the GPIO board if

present. See Figure 3.

STEP 5

Remove the four screws securing the back

panel to the keypanel frame. If a GPIO board

is present, be careful to not disturb any of

the wiring harness for the board. See Figure

STEP 6

Locate the accessory connector on the

keypanel motherboard. See Figure 4.

STEP 7

Locate the mating connector on the bottom

of the CSI-100 board. See Figure 5.

STEP 8

With the BNC connector on the CSI-100

board facing out from the unit, slide the

connector of the CSI-100 board onto the

Figure 2 - Bottom screw locations for backpanel removal.

Figure 3 - Top and rear screw/standoff locations for backpanel removal.

Figure 1 - CSI-100 coaxial connector location on backpanel.

Figure 5 - Bottom view of CSI-100 board.

Figure 4 - Accessory connector on KP-32 series board.

Figure 6 - View of installed CSI-100 board.

accessory connector on the keypanel

motherboard being careful to align the

mating pins properly.

STEP 9

Remove the knockout on the backpanel to

allow the BNC on the CSI-100 board to pass

through the backpanel.

STEP 10

Place the backpanel on the keypanel and

then place the washer(s) and nut over the

BNC connector and tighten.

STEP 11

Repeat steps 5 through 3 in reverse to

reassemble the keypanel.

END OF PROCEDURE

Andere Handbücher für KP-32

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere RTS Aufnahmegeräte Handbücher

RTS

RTS OMI-2 Bedienungsanleitung

RTS

RTS SIP-ISDN Montageanleitung

RTS

RTS 9V2 Bedienungsanleitung

RTS

RTS OMNEO Bedienungsanleitung

RTS

RTS Zeus III Bedienungsanleitung

RTS

RTS DSI 2008 Bedienungsanleitung

RTS

RTS TIF-2000A Bedienungsanleitung

RTS

RTS SSA-324 Bedienungsanleitung

RTS

RTS IFB-828 Bedienungsanleitung

RTS

RTS WKP-8 Bedienungsanleitung

RTS

RTS KP 32 CLD Bedienungsanleitung

RTS

RTS OMNEO OEI-2 Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch