Rustibus 25 AIR Bedienungsanleitung
025-3000
RUSTIBUS® 25 AIR
Miniblaster
OPERATION MANUAL
© COPYRIGHT 2015
© Copyright 2015 by DSS.
All rights reserved printed in the United States of America. No part of this manual may be used or
reproduced in any form or by any means, stored in data base or retrieval system, without prior written
permission from Dalseide Shipping Services (DSS).
Making copies of this manual for any purpose other than your own personal use is a violation of the
United States copyright laws.
February 1, 2015 issue 1.0
Specications subject to changes without notice!
If you have any questions, please contact us:
Rustibus INC (DSS)
2901 West Sam Houston Pkwy, North
Suite e-325
Houston, TX 77043 USA
Email: [email protected]om
Phone: +1 832 203 7170
Fax: +1 832 203 7171
www.rustibus.com
INTRODUCTION
This operation and maintenance manual is furnished with each Rustibus® 25 Miniblaster unit. It outlines
general equipment use and the operation and maintenance requirements for ecient and safe
operation.
READ ALL INSTRUCTIONS AND DATA IN THIS OPERATION AND MAINTENANCE MANUAL PRIOR TO
OPERATION OF THIS EQUIPMENT.
These instructions are for your protection and convenience. Please read them carefully since failure to
follow the precautions could result in injury.
Whenever using powered equipment, basic safety precautions should be followed.
If after reading this manual anything seems unclear, contact a Rustibus INC (DSS) directly by dialing
+1 832 203 7170.
GENERAL DESCRIPTION
The Rustibus® 25 Miniblaster is an easy to handle, light weight surface preparation tool with a lot of
power. This versatile piece of equipment utilizes a variety of abrasives from wire brushes, coating removal
discs to erasers for removal of adhesive products.
TECHNICAL DETAILS
Length: 275 mm / 11”
Length w/wheel: 325 mm / 13”
Height: 150 mm / 6”
Height w/handle: 240 mm / 9,45”
Width: 80 mm / 3,15”
Width w/handle: 175 mm / 6,89”
Total Weight: 1,5 kg / 3,2 lbs
Air Cons: 113 LPM / 4 CFM
Work press: 6,3 bar / 90 psi
Air inlet: 1/4”
RPM: 3500
Noise level*:83 dB
Vibration: 2,42 m/s²
*Noise level dependent on surface.
HELPFUL IDENTIFIERS
In addition to information on installation and operation, this instruction manual may contain WARNINGS
and CAUTIONS pertaining to user safety, and NOTES on important, useful operating guidelines.
A WARNING indicates a potentially hazardous situation, which if not avoided, could result in death or
serious injury.
A CAUTION indicates a potentially hazardous situation, which, if not avoided may result in minor or
major injury.
A NOTE is to alert the operator to important operating information.
IMPORTANT
The safeguards and instructions in this manual cannot cover all possible conditions and situations, which
may occur. As we cannot control the correct mounting, usage and utilization of this product, we can not
be responsible or liable for any injuries, damages, losses or costs, which result from using our products in
any way.
Do not attempt to operate this tool until you have read and understood all safety precautions and
instructions listed in this manual.
It is your responsibility to make this safety information available to others that will operate this product.
Incorrect operation of this unit can cause serious injury.
Maintain your company’s re and safety procedures while operating this tool.
WARNING
Rotating equipment may cause serious injury – protect hands, feet, eyes and hearing.
Debris from scraping action may be scattered.
Rustibus® 25 may produce low energy sparks.
Respiratory protection should be considered depending on material being removed.
Before starting Rustibus® 25, be sure all hoses and ttings are the correctly sized and secured.
Never attempt to de-scale areas when its mechanical integrity is in doubt, according to applicable
codes and standards.
Never install, remove or perform any maintenance on the Rustibus® 25 when
the air supply is connected.
Always keep both hands on handles when operating the Rustibus® 25.
Never use non Ex/Atex certied machines in potentially explosive atmospheres.
Never operate the Rustibus® 25 while wearing loose hanging chains, hanging
ID/security badges or garments that may be caught in the rotating parts.
On vertical sections, work with the Rustibus® 25 between knee and shoulder
height to avoid strain. If used over prolonged periods for vertical work, lifting assistance
should be considered to prevent accidents, fatigue etc.
Rustibus® 25 should be properly maintained and stored when not in use to
avoid damage to parts.
Rustibus® 25 accessories are designed for use on the Miniblaster and therefore should not be
utilized on or in conjunction with any other machines.
CAUTION
PLEASE READ THE WARNINGS BEFORE OPERATION
WARNINGS:
When connecting, changing, or repairing the Rustibus® 25,
the air supply MUST ALWAYS be disconnected.
IMPORTANT:
Do not push down on your machine. This only damages the tool, it does not improve results.
• Ear & face protection should be used for your own safety.
It is recommended to use a safety screen
when operating the Rustibus® 25.
Wear protective gloves and safety shoes.
WORKING SAFELY WITH THIS MACHINE IS POSSIBLE ONLY WHEN THE OPERATING AND SAFETY
INFORMATION ARE READ COMPLETELY AND THE INSTRUCTIONS CONTAINED THEREIN ARE STRICTLY
FOLLOWED. IN ADDITION, THE GENERAL SAFETY INSTRUCTIONS IN THE ENCLOSED BOOKLET MUST
BE FOLLOWED. BEFORE USING FOR THE FIRST TIME, TAKE A LOOK AT THE MACHINE TO UNDERSTAND
THE PRACTICAL WORKINGS OF IT.
SAFETY PRECAUTIONS TO FOLLOW
• Always install, operate, inspect and maintain this product in accordance with all applicable standards
and regulations (local, state, country, federal, etc.).
• Compressed air models always use clean, dry air at 90 psi (6.2 bar/620 kPa) maximum air pressure at
the inlet. Higher pressure may result in hazardous situations including excessive speed, rupture, or
incorrect output torque or force.
• Be sure all hoses and ttings are the correctly sized and secured.
• Ensure an accessible emergency shut o has been installed. Make others aware of its location.
• Do not use damaged, frayed, or deteriorated air hoses and ttings.
• Keep clear of whipping air hoses. Shut o the compressed air before approaching a whipping hose.
• Check the compressed air at regular intervals to ensure the compressed air is clean and oiled. If it is
necessary integrate a service until into the compressed air line.
• If the tool is not in use, disconnect it from the air supply and store it in a suitable clean/dry location to
prevent any unauthorized use.
• Keep in mind that brushes can create sparks while running on hard surfaces. Take precautions while
in use.
• Always turn o and disconnect the tool from its power supply before installing, removing or
adjusting any accessory, or before performing any maintenance on the tool.
• Do not lubricate tools with ammable or volatile liquids such as kerosene, diesel or jet fuel. Use only
recommended lubricants.
• Keep work area clean, uncluttered, ventilated and illuminated.
• Do not operate the machine while ammable or volatile liquids such as gasoline, diesel or jet fuel are
present. Failure to do so can result in explosion. (When applicable.)
• Do not remove any labels. Replace any damaged label.
SAFETY PRECAUTIONS TO FOLLOW
• Always wear protection when operating or performing maintenance on this tool.
• Always wear hearing protection when operating this tool.
• Always use Personal Protective Equipment appropriate to the tool used and material worked. This
may include dust mask or other breathing apparatus, safety glasses, ear plugs, gloves, apron, safety
shoes, hard hat and other equipment.
• Prevent exposure and breathing of harmful dust and particles created by power tool use:
- Some dust created by power sanding, sawing, and grinding, drilling, and other construction
activities contains chemicals known to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
- Lead from lead based paints,
- Crystalline silica from bricks and cement and other masonry products, and
- Arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are specially designed to lter out microscopic
particles.
• Keep others a safe distance from your work area, or ensure they use appropriate Personal Protective
Equipment.
• This tool is not designed for working in explosive environments, including those caused by fumes
and dust, or near ammable materials.
• Be aware of buried, hidden or other hazards in your work environment. Do not contact or damage
cords, conduits, pipes, or hoses that may contain electrical wires, explosive gases or harmful liquids.
• Keep hands, loose clothing, long hair and jewelry away from working end of tool.
• Do not indulge in horseplay. Distraction can cause accidents.
• Power tools can vibrate in use. Vibration, repetitive motions or uncomfortable positions may be
harmful to your hands and arms. Stop using any tool if discomfort, tingling feeling or pain occurs.
Seek medical advices before resuming use.
• Keep body stance balanced and rm. Do not overreach when operating this tool. Anticipate and be
alert for sudden changes in motion, reaction torques, or forces during startup and operation.
• Tool and/or accessories may briey continue their motion after throttle is released.
USING THE TOOL
• To avoid accidental starting – ensure tool in“o”position before applying air pressure. Avoid throttle
when carrying, and release throttle with loss of air.
• Ensure work pieces are secure. Use clamps or vises to hold work piece whenever possible.
• Make sure the hex socket wrench is removed before you start up!
• Make sure you have a rm grip on the tool before you begin.
• Do not carry or drag the tool by the hose.
• Do not use power tools when tired, or under the inuence of medication, drugs, or alcohol.
• Never us a damaged or malfunctioning tool or accessory.
• Do not modify the tool, safety devices, or accessories.
• Do not use this tool for purposed other than those recommended.
• Never operate a tool with an accessory unless it is properly installed and the tool is held rmly against
the work.
• Always use a retainer, when furnished, in addition to proper barriers to protect persons in surround-
ing or lower areas from possible ejected accessories.
• When wearing gloves and operating models with inside trigger, always be sure that the gloves will
not prevent the trigger from being released.
• Keep hands and ngers away from the throttle lever until it is time to operate the tool.
• Never rest the tool on your foot.
• Never point the tool at anyone.
• Compressed air is dangerous. Never point an air hose at yourself or others.
• Never blow clothes free of dust with compressed air.
• Be sure all hose connections are tight. A loose hose not only leaks but can come completely o the
tool and while whipping under pressure, can injure the operator and other in the area. Attach safety
cables to all hosed to prevent injury in case a hose is accidentally broken.
USING THE TOOL
• Never disconnect a pressurized air hose. Always turn o the air supply and bleed the tool before
disconnecting a hose.
• Use only proper cleaning solvents to clean parts. Use only cleaning solvents which meet current
safety and health standards. Use cleaning solvents in a well ventilated area.
• Do not ush the tool or clean any parts with diesel fuel. Diesel fuel residue will ignite in the tool when
the tool is operated, causing damage to internal parts. When using models with outside triggers or
throttle levers, take care when setting the tool down to prevent accidental operation.
• Do not operate the tool with broken or damaged parts.
• Never start the tool when it is lying on the ground.
• ALWAYS hold both the tool body and the vertical handle while in use.
• This tool is not designed for working in explosive atmospheres.
Inhaltsverzeichnis
Andere Rustibus Elektrowerkzeuge Handbücher
