Ruwido Easytip Z3 Bedienungsanleitung

Operating Instructions

Congratulations on purchasing this high performance easytip Z3

universal remote control. Great care has been taken over the

design and manufacture of this product and in normal use it will

give many years of satisfactory service. The following pages

describe how to get the best from your new remote.

Inserting and changing the batteries

Your easytip Z3 is powered by two alkaline 1.5 V batteries

(IEC LR 03, AAA). Wherever possible, ensure that new

batteries are used. Never mix old and new batteries

together as this will effect the performance of the

controller and shorten the battery life. Once the batteries

have been inserted, check that the red LED flashes when

any of the keys of your remote are depressed, this confirms

correct installation of the batteries.

Please Note:

Insert batteries following the markings on the inside of

the battery compartment.

Immediately dispose of any leaking batteries.

Dispose of old batteries as per manufacturers instructions.

User Manual

Helpline 00800 31133113 1

GB User Manual

D Bedienungsanleitung

I Istruzioni per l’usoF Mode d’emploiNL Gebruiksaanwijzing

1. Useful Tips before programming

your easytip Z3

In the back pages of this manual you will find the 4-digit

codes which allow you to set up your easytip Z3 controller.

After finding your brand of TV, Satellite or VCR in the back

pages of the manual, you will see alongside several 4-digit

codes. You should start with the first 4-digit code in the

list. If after programming this first 4-digit code your easytip

Z3 does not operate correctly, then move to the next 4-

digit code in the list until you have tried every code. These

code numbers are specific to the Z3 remote and are not a

reference to your particular model of TV etc. Each code

number in the back of the book performs a particular

function when activated. As you progress through the

code list against your brand of TV etc. certain controls on

the handset may not function correctly, this is perfectly

normal and can often be solved by continuing through the

other codes in the list. Do not assume that the first number

that operates your TV, Satellite or VCR is the correct and

final code. You must ensure that before contacting the

HELPLINE, you have tried and tested all the codes against

your brand of TV, Satellite or Video Recorder.

Function keys explained

ON/OFF Power/Standby

MUTE TV speaker mute

MENU Menu on/off and

VCR: Record (press twice in quick

succession)

F Function key for programming

User Manual

Helpline 00800 31133113Helpline 00800 31133113

Function keys explained

OK/Play/Pause

TV: Norm, AV function and

confirmation key in the menu

SAT: Radio, AV function and

confirmation key in the menu

VCR: Play, Pause and AV function

Volume +/- Volume up/down and cursor

left/right in menu

Programme +/- Channel up/down and cursor

up/down in menu

Stop Stop:Video: Stop play, stop rewind, stop

fast forward, stop record.

REW Fast rewind of video cassette

FFW Fast forward of video cassette

Stellring Adjusting ring to switch

between TV, VCR and SAT.

Please note: Some TVs and SAT receivers may not support all of

these functions.

User Manual

Helpline 00800 31133113Helpline 00800 31133113 3

GB User Manual

D Bedienungsanleitung

I Istruzioni per l’usoF Mode d’emploiNL Gebruiksaanwijzing

Programm +/-

Volume +/-

Stellring

OK/Play/Pause

REW

Stop

FFW

ON/OFF

MUTE

Function keys for programming

the 4 Digit Code

Since the easytip Z3 has not got a numeric keypad, the

function keys on your controller are assigned to numbers

as follows:

1 = Up

2 = Left

3 = (OK/Norm)

4 = Right

5 = Down

e.g.:

To enter the code 1353, press in succession the

following keys:

Up for 1

(OK/Norm) for 3

Down for 5

(OK/Norm) for 3

The combination of these keys equals the code 1353.

User Manual

Helpline 00800 31133113

Programme + = 1

Programme – = 5

Volume + = 4

OK/Norm = 3

Volume – = 2

Two Ways of programming your Z3

• By Direct Code input from codes at the back of the

manual (preferred)

• By Search Mode (secondary method)

We would normally recommend using the dedicated code

numbers in the back of this booklet to setup your remote.

These numbers are particular to your brand of TV and will

inevitably give best results. As a secondary setup method,

your remote can undertake a complete code search. The

code search method is often used when a particular brand

is not listed, or when some features are not responding to

direct code input. As there are a great number of codes for

the unit to select and test, search mode can take upto 15

minutes to complete.

The 5 Second Rule

Your new easytip Z3 needs your help to get started.

We recommend that you study the step by step

instructions before programming the codes. The basis of

this programming is the 5 Second Rule. Each successive

action when programming must be completed within 5

seconds or the unit will revert back to normal operation.

This is deliberate so that other users of your remote will

not inadvertently reprogram the unit.

User Manual

Helpline 00800 31133113 5

GB User Manual

D Bedienungsanleitung

I Istruzioni per l’usoF Mode d’emploiNL Gebruiksaanwijzing

Quick Set-up Reference

Step 1 Insert batteries (checking correct polarity)

Step 2 Choose the device you want to control by turning

the adjusting ring until the printed ”TV”, ”VCR” or

”SAT” is inline with the pointer on the housing of

your remote.

Step 3 Switch on the chosen device TV, VCR, SAT. (if

setting up for TV, then TV must be fully on with a

broadcast picture on the screen)

Step 4 Press and hold the (F) key until the LED flashes

twice in quick succession.(approx 2 seconds)

Step 5 After the two flashes, remove your finger from the

(F) key and within 5 seconds input the code from

the manual.

Step 6 After you have input the code, wait for the LED to

flash twice, this confirms that the number you

selected has been installed into the unit correctly.

Step 7 Once the code has been installed, press the

(ON/OFF) key on the controller. If the (TV etc)

responds by going into standby mode then

continue to try all the other functions. If some

functions do not work correctly then move onto

the next code in the list repeating from Step 3.

What to do if the TV does not respond

• Either the 4-digit code, or part of the programming

sequence was not completed within 5 seconds or the

code was not recognised. Please re-check the 4-digit

code in the manual or move onto the next code in the list

against your particular brand. Also ensure that the codes

entered are from the correct section of the manual.

User Manual

Helpline 00800 31133113

Programming the easytip Z3 in search mode

Note:

it is advised not to use search function before using the direct

codes at the back of the manual.

If the listed codes failed to operate the TV, VCR or SAT, or

if the manufacturer was not included in the manual, then

the search mode should be used. Search mode allows the

controller to search and test every code in its memory.

During search mode the remote is sending a signal to your

device every other second. If the unit finds a compatible

signal it will power down the device into standby mode. If

this happens then test all the other functions of the

remote. If some functions do not work correctly then its

possible your remote has found the first of many

compatible codes. At this point you should continue the

search until a more compatible code is found. As there are

many codes for the controller to select and test, search

mode takes up to 15 minutes to perform.

How to run the search mode (code 1111)

Step 1 Switch on your TV, Sat, VCR (each unit must be

fully on with a broadcast picture on the screen or

with a running video tape in the video recorder).

Step 2 Choose the device you want to control by turning

the adjusting ring until the printed ”TV”, ”VCR” or

”SAT” is inline with the pointer on the housing of

your remote.

Step 3 Press and hold the (F) key until the LED flashes

twice. (approx 2 seconds)

Step 4 Within 5 seconds input the code 1111 (up, up, up,

up). After you have input the code, wait for the

LED to flash twice, this confirms that the number

you selected has been installed into the unit

correctly.

User Manual

Helpline 00800 31133113 7

GB User Manual

D Bedienungsanleitung

I Istruzioni per l’usoF Mode d’emploiNL Gebruiksaanwijzing

Step 5 Search Mode for TV & Sat

Within 5 seconds after the double flash press and

hold the (ON/OFF), this will start the search mode.

You must hold this key down continually to enable

the search. Confirmation of the search can be

noted by the red LED flashing every other second.

If the remote finds a compatible code the TV will

go into standby mode. After this test all other

functions of the remote.

PLEASE DO NOT ASSUME THAT THE FIRST CODE

FOUND IS THE CORRECT CODE.

Search Mode for Video Recorders (VCR)

When using Search mode for the VCR press and

hold the (STOP) key as opposed to (ON/OFF) key.

Instead of putting the VCR into standby mode, the

search facility will ‘park’ or ‘stop’ the tape from

playing (before using search the video recorder

must have a playing tape in the unit).

Step 6 After your TV, SAT has switched into standby

mode, or the video cassette has stopped running,

press and hold the (F) key until the LED flashes

twice. This will store the code.

IMPORTANT!

Code search begins from the last code number found in the

previous search. When the end of the code list is reached the

LED flashes 3 times in quick succession and the search

restarts from the beginning of the list.

User Manual

Helpline 00800 31133113

Determining the 4-digit code found by

automatic code search (after using search

facility)

It is useful to know which code your device responded to

in case it is inadvertently changed at any later date.

Step 1 Choose the device you want to control by turning

the adjusting ring until the printed ”TV”, ”VCR” or

”SAT” is inline with the pointer on the housing of

your remote.

Step 2 Press and hold the (F) key until the LED flashes 3

times twice. (approx 2 seconds)

Step 3 After the two flashes and within 5 seconds input

the code 1112. After you have input the code, wait

for the LED to flash twice, this confirms that the

number you selected has been installed into the

unit correctly.

Step 4 To determine the stored code press the following

keys:

up for the first digit

left for the second digit

(OK/Norm) for the third digit

right for the fourth digit

After pressing one of these keys, count the number

of flashes emitted by the LED. As long as you do

not exceed 5 seconds between each process you

can press any of these keys as often as you want.

So you do not have to hurry or panic if you miss a

flash.

Make sure that you count the flash that occurs

including the initial flash when depressing the key.

User Manual

Helpline 00800 31133113 9

GB User Manual

D Bedienungsanleitung

I Istruzioni per l’usoF Mode d’emploiNL Gebruiksaanwijzing

Example:

After pressing the (Programme +) key the LED flashes

once. So the first digit of your code is 1.

After pressing the (Volume -) key the LED flashes

thrice. So the second digit of your code is 3.

After pressing the (OK/Norm) key the LED flashes

five times. So the third digit of your code is 5.

After pressing the (Volume +) key the LED flashes

thrice. So the fourth digit of your code is 3.

In this example the code is 1353.

Please make a note of the codes in the box below

for eventual reprogramming.

Please write down your 4-digit codes here:

VCR

SAT

User Manual

Helpline 00800 31133113

Inhaltsverzeichnis

Sprachen:

Andere Ruwido Fernbedienung Handbücher

Ruwido

Ruwido easytip 4 Bedienungsanleitung

Ruwido

Ruwido Easytip 7 Bedienungsanleitung

Ruwido

Ruwido Easytip 1 Bedienungsanleitung

Ruwido

Ruwido M_2 Bedienungsanleitung

Ruwido

Ruwido Swisscom Box Bedienungsanleitung

Ruwido

Ruwido Z1 Bedienungsanleitung

Ruwido

Ruwido 850A Bedienungsanleitung

Ruwido

Ruwido RC 12110 Bedienungsanleitung

Ruwido

Ruwido H1 Bedienungsanleitung

Ruwido

Ruwido easytip series Bedienungsanleitung

Ruwido

Ruwido Amadeus Symphony Bedienungsanleitung

Ruwido

Ruwido 2779 Series Bedienungsanleitung

Ruwido

Ruwido Symphony Bedienungsanleitung

Ruwido

Ruwido tantum RC 12123 Bedienungsanleitung

Ruwido

Ruwido 827A01 Bedienungsanleitung

Ruwido

Ruwido Easytip S series Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung

Ruwido easytip Z3 Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken