Ryobi PLASMA-40 Bedienungsanleitung

OWNER’S OPERATING MANUAL

PLASMA CUTTER

MODEL PLASMA-40

KEEP THIS MANUAL FOR FUTURE REFERENCE

Your new inverter generator has been engineered and manufactured to Ryobi’s

high standard of dependability, ease of operation and operator safety. Properly

cared for, it will give you years of rugged, trouble free performance. If you use

your inverter generator properly and only for what it is intended, you will enjoy

years of safe, reliable service.

SPECIFICATIONS

Rated input power supply.......................................................AC230V±5% 50/60 z

Rated input capacity...................................................................................... 6.4kVA

Rated output voltage..................................................................................... 88-96V

Current adjustment range............................................................................. 20-40A

Rated duty cycle................................................................................................ 80%

No load voltage................................................................................................ 310V

Overall efficiency................................................................................................85%

ousing protection grade................................................................................IP21S

Post flow time........................................................................................................7s

Gas pressure range............................................................................0.35-0.55Mpa

Max. cutting capacity (mild steel)............................... Clean cut 8mm/ Sever 12mm

Power factor.............................................................................................. 0.70 cosφ

Noise......................................................................................................... <70dB(A)

Insulation grade...................................................................................................... F

Dimensions............................................................................... 480 x 160 x 315mm

Net weight........................................................................................................ 7.8kg

THANK YOU FOR BUYING A RYOBI

PLASMA CUTTER

CAUTION: Carefully read through this entire owner’s

manual, paying close attention to the general

safety rules and rules for safe operation,

before using.

IMPORTANT SAFETY INSTRUCTIONS

The purpose of safety rules is to attract your

attention to possible dangers. The safety symbols

and the explanations with them, require your

careful attention and understanding. The safety

warnings do not by themselves eliminate any

danger. The instruction or warnings they give are

not substitutes for proper accident prevention

measures.

SAFETY ALERT SYMBOL. Indicates

danger, caution or warning. May be used

in conjunction with other symbols or

pictures.

Failure to obey a safety warning can result in

serious injury to yourself or to others. Always follow

the safety precautions to reduce the risk of fire,

electric shock and personal injury.

Do not attempt to operate this tool until you have

read thoroughly and completely understood the

safety rules, etc. contained in this manual. Failure

to comply can result in accidents involving fire,

electric shock or serious personal injury. Save this

Owners Operating Manual and review it frequently

for continual safe operation and for instructing

others who may use this tool.

EMF INFORMATION

Considerations About Welding And The Effects Of

Low Frequency Electric And Magnetic Fields.

Welding current, as it flows through welding cables,

will cause electro- magnetic fields. There has been

and still is some concern about such fields.

owever, after examining more than 500 studies

spanning 17 years of research, a special blue

ribbon committee of the National Research Council

concluded that: “The body of evidence, in the

committee’s judgment, has not demonstrated that

exposure to power- frequency electric and

magnetic fields is a human-health hazard.”

owever, studies are still going forth and evidence

continues to be examined. Until the final

conclusions of the research are reached, you may

wish to minimize your exposure to electromagnetic

fields when welding or cutting.

To reduce magnetic fields in the workplace, use the

following procedures:

1. Keep cables close together by twisting or

taping them.

2. Arrange cables to one side and away from

the operator.

3. Do not coil or drape cables around your body.

4. Keep welding power source and cables as far

away from operator as practical.

5. Connect work clamp to work piece as close

to the weld as possible.

ABOUT PACEMAKERS

Pacemaker wearers consult your doctor first. If

cleared by your doctor, then following the above

procedures is recommended.

WELDING HAZARDS

The symbols shown below are used throughout this

manual to call attention to and identify possible

hazards. When you see the symbol, watch out, and

follow the related instructions to avoid the hazard.

Only qualified persons should service, test,

maintain, and repair this unit.

During servicing, keep everybody, especially

children, away.

ARC RAYS can burn eyes and skin; NOISE can

damage hearing. Arc rays from the welding

process produce intense heat and strong

ultraviolet rays that can burn eyes and skin.

Noise from some processes can damage

hearing.

1. Wear a welding helmet fitted with a proper

shade of filter (ANSI Z49.1) to protect your

face and eyes when welding or watching.

2. Wear approved safety glasses. Side shields

recommended. Never wear contact lenses

while welding.

3. Use protective screens or barriers to protect

others from flash and glare; warn others not

to watch the arc.

4. Wear protective clothing made from durable,

flame-resistant material (wool and leather)

and foot protection.

5. Use approved ear plugs or ear muffs if noise

level is high.

ARC RAYS

Can Burn

IMPORTANT SAFETY INSTRUCTIONS

Touching live electrical parts can cause fatal

shocks or severe burns. The electrode and

work circuit is electrically live whenever the

output is on. The input power circuit and

machine internal circuits are also live when

power is on. In semiautomatic or automatic

wire welding, the wire, wire reel, drive roll

housing, and all metal parts touching the

welding wire are electrically live. Incorrectly

installed or improperly grounded equipment is

a hazard.

1. Do not touch live electrical parts.

2. Wear dry, hole-free insulating gloves and body

protection.

3. Insulate yourself from work and ground using

dry insulating mats or covers.

4. Disconnect input power or stop engine before

installing or servicing this equipment. Lock input

power disconnect switch open, or remove line

fuses so power cannot be turned on

accidentally.

5. Properly install and ground this equipment

according to its Owner’s Manual and national,

state, and local codes.

6. Turn off all equipment when not in use.

Disconnect power to equipment if it will be left

unattended or out of service.

7. Use fully insulated electrode holders. Never dip

holder in water to cool it or lay it down on the

ground or the work surface. Do not touch

holders connected to two welding machines at

the same time or touch other people with the

holder or electrode.

8. Do not use worn, damaged, undersized, or

poorly spliced cables.

9. Do not wrap cables around your body.

10. Ground the workpiece to a good electrical

(earth) ground.

11. Do not touch electrode while in contact with

the work (ground) circuit.

12. Use only well-maintained equipment. Repair

or replace damaged parts at once.

13. In confined spaces or damp locations, do not

use a welder with AC output unless it is

equipped with a voltage reducer. Use

equipment with DC output.

14. Wear a safety harness to prevent falling if

working above floor level.

15. Keep all panels and covers securely in place.

FUMES AND GASES can be hazardous to your

health. Welding produces fumes and gases.

Breathing these fumes and gases can be haz-

ardous to your health.

1. Keep your head out of the fumes. Do not

breath the fumes.

2. If inside, ventilate the area and/or use

exhaust at the arc to remove welding fumes

and gases.

3. If ventilation is poor, use an approved air-

supplied respirator.

4. Read the Material Safety Data Sheets

(MSDSs) and the manufacturer’s instruction

for metals, consumables, coatings, and

cleaners.

5. Work in a confined space only if it is well

ventilated, or while wearing an air-supplied

respirator.

Shielding g ses used for welding c n displ ce

air causing injury or death. Be sure the

breathing air is safe.

6. Do not weld in locations near degreasing,

cleaning, or spraying operations. The heat

and rays of the arc can react with vapors to

form highly toxic and irritating gases.

7. Do not weld on coated metals, such as

galvanized, lead, or cadmium plated steel,

unless the coating is removed from the weld

area, the area is well ventilated, and if

necessary, while wearing an airsupplied

respirator. The coatings and any metals

containing these elements can give off toxic

fumes if welded.

ELECTRIC SHOCK

Can Kill

FUMES & GASES

Can Be Dangerous

FLYING SPARKS AND HOT METAL can cause

injury.

Chipping and grinding cause flying metal.

As welds cool, they can throw off slag.

1. Wear approved face shield or safety goggles.

Side shields recommended.

2. Wear proper body protection to protect skin.

CYLINDERS can explode if damaged.

Shielding gas cylinders contain gas under high

pressure. If damaged, a cylinder can explode.

Since gas cylinders are normally part of the

welding process, be sure to treat them

carefully.

1. Protect compressed gas cylinders from

excessive heat, mechanical shocks, and arcs.

2. Install and secure cylinders in an upright

position by chaining them to a stationary

support or equipment cylinder rack to

prevent falling or tipping.

3. Keep cylinders away from any welding or other

electrical circuits.

4. Never allow a welding electrode to touch any

cylinder.

5. Use only correct shielding gas cylinders,

regulators, hoses, and fittings designed for the

specific application; maintain them and

associated parts in good condition.

6. Turn face away from valve outlet when opening

cylinder valve.

7. Keep protective cap in place over valve except

when cylinder is in use or connected for use.

WELDING can cause fire or explosion.

Sparks and spatter fly off from the welding arc.

The flying sparks and hot metal, weld spatter,

hot workpiece, and hot equipment can cause

fires and burns. Accidental contact of electrode

or welding wire to metal objects can cause

sparks, overheating, or fire.

1. Protect yourself and others from flying sparks

and hot metal.

2. Do not weld where flying sparks can strike

flammable material.

3. Remove all flammables within 35 ft (10.7 m) of

the welding arc. If this is not possible, tightly

cover them with approved covers.

4. Be alert that welding sparks and hot materials

from welding can easily go through small

cracks and openings to adjacent areas.

5. Watch for fire, and keep a fire extinguisher

nearby.

6. Be aware that welding on a ceiling, floor,

bulkhead, or partition can cause fire on the

hidden side.

7. Do not weld on closed containers such as

tanks or drums.

8. Connect work cable to the work as close to

the welding area as practical to prevent

welding current from traveling long, possibly

unknown paths and causing electric shock and

fire hazards.

9. Do not use welder to thaw frozen pipes.

10. Remove stick electrode from holder or cut off

welding wire at contact tip when not in use.

11. When not welding, make certain no part of the

electrode circuit is touching the work or

ground. Accidental contact can cause

overheating and create a fire hazard.

IMPORTANT SAFETY INSTRUCTIONS

FLYING SPARKS

Can Cause Injury

CYLINDERS Can

Explode If Damaged

WELDING Can

Cause Fire or Injury

IMPORTANT SAFETY INSTRUCTIONS

Moving parts, such as fans, rotors, and belts

can cut fingers and hands and catch loose

clothing.

1. Keep all doors, panels, covers, and guards

closed and securely in place.

2. Stop engine before installing or connecting

unit.

3. ave only qualified people remove guards or

covers for maintenance and troubleshooting as

necessary.

4. To prevent accidental starting during servicing,

disconnect negative (-) battery cable from

battery.

5. Keep hands, hair, loose clothing, and tools

away from moving parts.

6. Reinstall panels or guards and close doors

when servicing is finished and before starting

engine.

SPARKS can cause BATTERY GASES TO E -

PLODE; BATTERY ACID can burn eyes and

skin. Batteries contain acid and generate explo-

sive gases.

1. Always wear a face shield when working on

a battery.

2. Stop engine before disconnecting or

connecting battery cables.

3. Do not allow tools to cause sparks when

working on a battery.

4. Do not use welder to charge batteries or jump

start vehicles.

5. Observe correct polarity (+ and –) on

STEAM AND PRESSURIZED HOT COOLANT

can burn face, eyes, and skin.

The coolant in the radiator can be very hot and

under pressure.

1. Do not remove radiator cap when engine is

hot. Allow engine to cool.

2. Wear gloves and put a rag over cap area when

removing cap.

3. Allow pressure to escape before completely

removing cap.

1. igh-frequency ( .F.) can interfere with radio

navigation, safety services, computers, and

communications equipment.

2. ave only qualified persons familiar with

electronic equipment install, test, and service

.F. producing units.

3. The user is responsible for having a qualified

electrician promptly correct any interference

problem resulting from the installation.

4. If notified by the FCC about interference, stop

using the equipment at once.

5. ave the installation regularly checked and

maintained.

6. Keep high-frequency source doors and panels

tightly shut, keep spark gaps at correct setting,

and use grounding and shielding to minimize

the possibility of interference.

MOVING PARTS

Can Cause Injury

SPARKS Can Cause

BATTERY GASES

TO E PLODE

SPARKS Can Cause

BATTERY GASES

TO E PLODE

H.F. RADIATION Can

Cause Interference

1. Electric current flowing through ny conductor

c uses loc lized Electric nd M gnetic Fields

(EMF). Welding current cre tes EMF fields

round welding c bles nd welding m chines.

2. EMF fields m y interfere with some

p cem kers, nd welders h ving p cem ker

should consult their physici n before welding.

3. Exposure to EMF fields in welding m y h ve

other he lth effects which re now not known.

4. All welders should use the following

procedures in order to minimize exposure to

EMF fields from the welding circuit:

5. Route the electrode nd work c bles together -

Secure them with t pe when possible.

6. Never coil the electrode le d round your

body.

7. Do not pl ce your body between the electrode

nd work c bles. If the electrode c ble is on

your right side, the work c ble should lso be

on your right side.

8. Connect the work c ble to the workpiece s

close s possible to the re being welded.

9. Do not work next to welding power source.

1. Lift unit with h ndle on top of c se.

2. Use h ndc rt or simil r device of dequ te

c p city.

3. If using fork lift vehicle, pl ce nd secure

unit on a proper skid before transporting.

1. Turn off input power using the disconnect

switch at the fuse box before working on the

equipment.

2. Install equipment in accordance with the

countries National Electrical Code, all local

codes and the manufacturer’s

recommendations.

3. Ground the equipment in accordance with the

countries National Electrical Code and the

manufacturer’s recommendations.

1. Do not touch hot parts bare handed.

2. Allow cooling period before working on

welding gun or torch.

1. Do not place unit on, over, or near

combustible surfaces.

2. Do not service unit near flammables.

1. Put on grounded wrist strap BEFORE handling

boards or parts.

2. Use proper static-proof bags and boxes to

store, move, or ship PC boards.

IMPORTANT SAFETY INSTRUCTIONS

ELECTRIC AND

MAGNETIC FIELDS

May Be Dangerous

FALLING UNIT Can

Cause Injury

FOR ELECTRICALLY

Powered Equipment

HOT PARTS Can

Cause Severe Burns

FIRE or E PLOSION

Hazard

STATIC Can Damage

PC Boards

IMPORTANT SAFETY INSTRUCTIONS

1. Allow cooling period; follow rated duty cycle.

2. Reduce current or reduce duty cycle before

starting to weld again.

3. Do not block or filter airflow to unit.

1. Consult the Owner’s M nu l for welding

s fety prec utions. Do not inst ll, oper te or

rep ir this equipment without re ding this

m nu l nd the s fety prec utions throughout.

2. Use only genuine repl cement p rts

OVERUSE Causes

OVERHEATING

READ THE

INSTRUCTIONS

ADDITIONAL SAFETY INSTRUCTIONS

1. ALWAYS ensure that there is full free air

circulating around the outer casing of the

machine, and that the louvres are

unobstructed.

2. ALWAYS use a proper welding face shield or

helmet, with suitable filter lenses. Proper

gloves and working clothes should be worn at

all times.

3. ALWAYS check that the pressure regulator and

gauges are working correctly. DO NOT

lubricate the regulator.

4. ALWAYS use the correct regulator. Each

regulator is designed to be used with a specific

gas.

5. ALWAYS inspect the hose before use to

ensure it is in good condition.

6. ALWAYS keep the free length of gas hose

outside the work area.

7. ALWAYS remove all flammable materials from

the welding area.

8. NEVER remove any of the panels unless the

machine is disconnected from the supply, AND

never use the machine with any of the panels

removed.

9. NEVER attempt any electrical or mechanical

repair unless your are a qualified technician.

If you have a problem with the machine contact

your local RYOBI dealer.

10. NEVER use or store in a wet/damp

environment. DO NOT EXPOSE TO RAIN.

11. NEVER use gas from a cylinder, the content

of which is unknown. It is important to ensure

the appropriate gas is being used.

12. NEVER use a damaged cylinder.

13. NEVER lift the cylinder by the valve.

14. NEVER expose the cylinder to a heat source

or sparks.

15. NEVER continue to weld, if, at any time, you

feel even the smallest electric shock. Stop

welding IMMEDIATELY, and DO NOT attempt

to use the machine until the fault is diagnosed

and corrected.

16. NEVER use the welder with input connections

greater than 10M in length.

17. NEVER point the torch at any person or

animal.

18. NEVER touch the torch nozzle until the welder

is switched OFF and the nozzle has been

allowed to cool off.

19. NEVER connect, disconnect, or attempt to

service the torch, until the machine is switched

OFF and disconnected from the mains supply.

20. NEVER allow the cables to become wrapped

around the operator or any person in the

vicinity.

21. Safety devices such as interlocks and circuit

breakers should not be disconnected or

shunted out.

22. Before installation, inspection, or service of

equipment, shut OFF all power and remove

line fuses to prevent accidental turning ON

of power.

23. Do not open power circuit or change polarity

while welding.

ADDITIONAL SAFETY INSTRUCTIONS

24. If, in an emergency, it must be disconnected,

guard against shock burns, or flash from switch

arcing. Always shut OFF and disconnect all

power to equipment. Power disconnect switch

must be available near the welding power

source.

25. Fully insulated electrode holders should be

used. Do NOT use holders with protruding

screws or with any form of damage.

26. Fully insulated lock-type connectors should be

used to join welding cable.

27. Frequently inspect cables for wear, cracks and

damage. IMMEDIATELY REPLACE those with

excessively worn or damaged insulation to

avoid possibly lethal shock from bared cable.

Cables with damaged areas may be taped to

give resistance equivalent to original cable.

Keep cable dry, free of oil and grease, and

protected from hot metal and sparks.

INSTALLATION

ENVIRONMENT

These units are designed for use in environments

with increased hazard of electric shock.

A. Examples of environments with increased

hazard of electric shock are:

1. In locations in which freedom of movement is

restricted, so that the operator is forced to

perform the work in a cramped (kneeling,

sitting or lying) position with physical contact

with conductive parts.

2. In locations which are fully or partially limited

by conductive elements, and in which there is

a high risk of unavoidable or accidental contact

by the operator.

3. In wet or damp hot locations where humidity

or perspiration considerable reduces the skin

resistance of the human body and the

insulation properties of accessories.

B. Environments with increased hazard of electric

shock do not include places where electrically

conductive parts in the near vicinity of the

operator, which can cause increased hazard,

have been insulated.

LOCATION

This machine can operate in harsh environments.

owever, it is important that simple preventative

measures are followed to assure long life and reli-

able operation:

• This machine must be located where there is

free circulation of clean air without restrictions

for air movement to and from the air vents. Do

not cover the machine with paper, cloth or rags

when switched on.

• Dirt and dust that can be drawn into the

machine should be kept to a minimum.

• This machine has a protection rating of IP21S.

Keep it dry and do not place it on wet ground

or in puddles. Do not use in wet or damp

locations. Store indoors.

• Locate the machine away from radio controlled

machinery. Normal operation may adversely

affect the operation of nearby radio controlled

machinery, which may result in injury or

equipment damage.

Read the section on electromagnetic compatibility

in this manual.

• Do not operate in areas with an ambient

temperature greater than 40°C.

TILTING

Place the machine directly on a secure, level

surface.

Do not place or operate this machine on a surface

with an incline greater than 15° from horizontal.

The machine may topple over if this procedure is

not followed.

VENTILATION

This cutting machine can create powerful cutting

current and has strict cooling requirements that

cannot be met with natural ventilation. Therefore

the built-in fan is very important in enabling the

machine to work stable with effective cooling. The

operator should make sure that the louvers be

uncovered and unblocked. The minimum distance

between the machine and nearby objects should

be 25cm.

Inhaltsverzeichnis

Andere Ryobi Schweißsystem Handbücher

Ryobi

Ryobi MMA-140 Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung