Safewatch QuickConnect Plus Betriebsanleitung

Safewatch







QuickConnect Plus

Security System

Programming Guide

BYPASS

RECORD

TEST

FUNCTION

STATUS

VOLUME PLAY

CODE CHIME

ESCAPE

ADD

DELETE

SELECT

1 2

4 5

ARMED

READY

OFF

AWAY

STAY

AUX

800-03859-4V2 11/10 Rev. A

-2-

TABLE OF CONTENTS

Data Fields ................................................................................................................................................................3

✻56 Enhanced Zone Programming ........................................................................................................................11

✻56 Enhanced Zone Programming Worksheet......................................................................................................14

✻80 Device Programming.......................................................................................................................................16

✻81 Zone Lists ........................................................................................................................................................17

Powerline Carrier Device Worksheet for ✻80 and ✻81 ...........................................................................................18

✻83 Enhanced Sequential Mode ...........................................................................................................................19

✻84 Assign Zone Voice Descriptors .......................................................................................................................20

Vocabulary Index (for ✻84 Assign Zone Voice Descriptors)...................................................................................20

✻85 Record Custom Voice Descriptors ..................................................................................................................21

5800 Series Transmitter Loop Numbers Diagram ..................................................................................................22

Safewatch QuickConnect Plus Control Defaults.....................................................................................................23

Safewatch QuickConnect Plus Summary of Connections Diagram.......................................................................24

Refer to the Safewatch QuickConnect Plus Installation and Setup Guide P/N 800-03857-4 or later for

detailed information on programming the system. The Installation and Setup Guide contains full

descriptions for all data fields.

Safewatch QuickConnect Plus is not intended for UL985 Household Fire applications unless a 24-

hour backup battery (P/N LYNXRCHKIT-HC or LYNXRCHKIT-SHA) is installed.

To Enter Programming Mode:

You may find it convenient to adjust the volume setting before entering the Programming Mode. This will allow

you to clearly hear feedback announcements or system beeps.

1. Power up, then depress [

✻

] and [#] both at once, within 50 seconds of powering up.

Enter: Installer Code (6 + 3 + 2 + 1) plus 8 + 0 + 0. System will display “Entering Program Mode”.

Notes: 1. If a different Installer Code has been programmed, enter: the New Installer Code + 8 + 0 + 0.

2. If

✻

98 was previously used to exit programming, the first method shown above must be used to re-

enter the program mode)

2. Upon entry into Program mode, data field “20 INSTALLER CODE” will be displayed (the first data field in

the system) and both keypad LEDs will flash.

To Program the Data Fields:

1. Press [

✻

] followed by the desired field number (e.g.,

✻

21), then make the required entry.

2. The keypad beeps three times after entering data, then displays the next data field in sequence.

3. For phone number and account number fields, press [

✻

] to end the entry if less than number maximum

number of digits is entered.

4. To view data entered in field, press [#] plus the field that you wish to view (e.g., #21). The system will beep

three times and data programmed for that field will be displayed to the right of the field number. The system

will scroll through the data for longer numbers and a beep will sound after each number is displayed or

three times after the final digit is displayed.

5. To delete an entry, simply press [

✻

] plus that field number and reenter the correct data. For phone number

and account number fields

✻

40-

✻

44,

✻

88 and

✻

94, press [

✻

] + field number + [

✻

Interactive Menu Modes:

There are six interactive menu modes as listed below. To enter these modes, first enter Program mode. While in

Program mode, press [

✻

] plus the mode number desired (e.g.,

✻

56).

✻

56 Enhanced Zone Programming .............. For programming zone characteristics, report codes, etc.

✻

80 Device Programming ............................. For programming Powerline Carrier Devices

✻

81 Zone List Programming ......................... For programming zone lists for use with Powerline Carrier Devices

✻

83 Enhanced Sequential Mode .................. For entering transmitter serial numbers

✻

84 Assign Zone Voice Descriptors.............. For assigning voice descriptors to zones

✻

85 Record Custom Voice Descriptors ........ For recording custom voice descriptors

- 3 -

To Initialize Download ID and Subscriber Account Number for Downloading:

✻

96 Resets all subscriber account numbers and CSID in preparation for an initial download.

To Load a Default Set:

✻

97 Enter a number 1-4 corresponding to the selected default table (See the Installation Instructions for the

default tables). Enter 0 if you are not selecting a default table.

To Exit Programming Mode:

✻

98 Exits programming mode and prevents re-entry by: Installer Code + 8+ 0 + 0. If ✻98 is used to exit

programming mode, system must be powered down, then press [✻] and [#] within 50 seconds of power

up to re-enter programming mode.

✻99

Exits programming mode and allows re-entry by: Installer Code + 8 + 0 + 0 or: Power-up, then press [✻]

and [#] within 50 seconds of power up.

DATA FIELDS

Data Field Display Function& Programming Options [ ] = Programmed Table 1 Default Values

SYSTEM SETUP (✻20– ✻30)

†

Entering a number other than the one specified may give unpredictable results.

2020

INSTALLER

INSTALLER INSTALLER

INSTALLER

CODE

CODECODE

CODE

Installer Code

[6321]

Enter 4 digits, 0–9

2121

QUICK

QUICK QUICK

QUICK

ARM

ARM ARM

ARM

ENABLE

ENABLEENABLE

ENABLE

Quick Arm Enable

†

[1]

0 = no; 1 = yes

2222

KEYPAD

KEYPAD KEYPAD

KEYPAD

BACKLIGHT

BACKLIGHTBACKLIGHT

BACKLIGHT

Keypad Backlight Timeout

[0]

0 = none (backlighting always on); 1 = backlight off after 10secs

2323

FORCED

FORCED FORCED

FORCED

BYPASS

BYPASSBYPASS

BYPASS

Forced Bypass

UL installations = 0

†

[1]

0 = none; 1 = bypass open zones

2424

RF RF

HOUSE

HOUSEHOUSE

HOUSE

ID ID

CODE

CODECODE

CODE

RF House ID Code

[00]

00 = disable all wireless keypad usage; 01–31 = 5804BD/5804BDV house ID

2525

X10

X10 X10

X10

HOUSE

HOUSE HOUSE

HOUSE

CODE

CODECODE

CODE

Powerline Carrier Device (X10) House ID

[0]

0 = A; 1 = B, 2 = C, 3 = D, 4 = E, 5 = F, 6 = G, 7 = H, 8 = I, 9 =

J, #10 = K, #11 = L,

#12 = M, #13 = N, #14 = O, #15 = P

2626

CHIME

CHIME CHIME

CHIME

BY BY

ZONE

ZONEZONE

ZONE

Chime By Zone

† [0]

0 = no; 1 = yes (program zones to chime on zone list 3)

CLO

CLOCLO

CLOCK

CK CK

DISPLAY

DISPLAYDISPLAY

DISPLAY

Real Time Clock Display

† [1]

0 = no; 1 = yes, display time on keypad

2929

DST

DST DST

DST

MNTH

MNTH MNTH

MNTH

STR/END

STR/ENDSTR/END

STR/END

Daylight Saving Time Start/End Month

[3, 11]

Start End

1-9, #+10,#+11,#+12. Enter 0,0 if no daylight savings time used.

3030

DST WEEK STR/END

DST WEEK STR/ENDDST WEEK STR/END

DST WEEK STR/END

Daylight Saving Time Start/End Weekend

[2,1]

Start End

0=disable; 1=first; 2=second; 3=third; 4=fourth; 5=last; 6=next to last; 7=third from last

- 4 -

Data Field Display Function& Programming Options [ ] = Programmed Table 1 Default Values

ZONE SOUNDS AND TIMING (✻31–

✻39)

3131

SINGLE

SINGLE SINGLE

SINGLE

ALARM

ALARM ALARM

ALARM

SND

SNDSND

SND

Single Alarm Sounding/Zone

UL installations = 0

† [0]

0 = Alarm Sounding Per Zone will be the same as the Swinger Shutdown” set in field *92;

1 = yes, limit once per arming period (also applies to long range radio output if “0” is

selected in ✻91 field)

3232

FIRE

FIRE FIRE

FIRE

SND

SNDSND

SND

TIMEOUT

TIMEOUT TIMEOUT

TIMEOUT

Sounder Timeout

† [0]

0=timeout; 1=no timeout

3333

ALRM

ALRM ALRM

ALRM

SND

SND SND

SND

TIMEOUT

TIMEOUTTIMEOUT

TIMEOUT

Alarm Bell Timeout

UL installations = 1 (4 min) minimum

† [1]

0 = none; 1=4 min; 2=8 min; 3=12 min; 4 = 16 min

3434

EXIT

EXIT EXIT

EXIT

DELAY

DELAYDELAY

DELAY

TIME

TIME TIME

TIME

Exit Delay

UL installations = 60 seconds max.

†[60]

45-96 = exit delay time (in seconds)

97 = 120 seconds

Note: The control validates the data entered in this field. If the selection is not valid the control will

emit a single long beep indicating that the selection has been rejected. The control replaces

the selection with the default value “60”, which is displayed on the keypad, and advances to

the next field.

SIA: Must be set to a minimum of 45 seconds.

3535

ENTRY

ENTRY ENTRY

ENTRY

DELAY

DELAYDELAY

DELAY

1 1

Entry Delay 1 (zone type 01)

UL installations = 45 seconds max.

† [30]

30-96 = entry delay 1 time (in seconds)

97 = 120 seconds

98 = 180 seconds

99 = 240 second

Note: The control validates the data entered in this field. If the selection is not valid the control will

emit a single long beep indicating that the selection has been rejected. The control replaces

the selection with the default value “30”, which is displayed on the keypad, and advances to

the next field.

SIA: The entry delay must be set to a minimum of 30 seconds. The sum of entry delay 1 entered in

Field *35 and the burglary abort window entered in *50 should not exceed 1 minute.

3636

ENTRY

ENTRY ENTRY

ENTRY

DELAY

DELAY DELAY

DELAY

Entry Delay 2 (zone type 02)

UL installations = 45 seconds max.

† [30]

30-96 = entry delay 2 time (in seconds)

97 = 120 seconds

98 = 180 seconds

99 = 240 second

Note: The control validates the data entered in this field. If the selection is not valid the control will

emit a single long beep indicating that the selection has been rejected. The control replaces

the selection with the default value “30”, which is displayed on the keypad, and advances to

the next field.

SIA: The entry delay must be set to a minimum of 30 seconds. The sum of entry delay 2 entered in

Field *36 and the burglary abort window entered in *50 should not exceed 1 minute.

3838

CON

CONCON

CONF

ARM

ARMARM

ARM

ING

INGING

ING

DING

DINGDING

DING

Confirmation of Arming Ding

Note: Confirmation ding only sounds when Safewatch QuickConnect Plus is Armed Away or disarmed

after being Armed Away. If Safewatch QuickConnect Plus is armed by RF button (key fob), a

confirmation ding occurs immediately after arming regardless of field

✻

38 settings. If Safewatch

QuickConnect Plus is disarmed by RF button (key fob), additional disarming confirmation ding occurs

immediately after disarming and is longer than arming confirmation ding.

† [0]

0 =

no arming confirmation ding after arming system by Safewatch QuickConnect Plus keypad or RF

keypad

;

1 = arming confirmation ding after arming system by Safewatch QuickConnect Plus keypad

or RF keypad;

2 = arming confirmation ding after arming from RF keypad only

† Entering a number other than the one specified may give unpredictable results.

- 5 -

Data Field Display Function& Programming Options [ ] = Programmed Table 1 Default Values

3939

CROSS ZONE TIMER

CROSS ZONE TIMERCROSS ZONE TIMER

CROSS ZONE TIMER

Cross Zone Timer

† [0]

Value Time Window Value Time Window

0 = No Cross Zoning 8 = 2 minutes

1 = 15 seconds 9 = 2 minute, 15 seconds

2 = 30 seconds # + 10 = 2 minute, 30 seconds

3 = 45 seconds # + 11 = 2 minute, 45 seconds

4 = 60 seconds # + 12 = 3 minutes

5 = 1 minute, 15 seconds # + 13 = 3 minute, 15 seconds

6 = 1 minute, 30 seconds # + 14 = 3 minute, 30 seconds

7 = 1 minute, 45 seconds # + 15 = 3 minute, 45 seconds

Note: If option ✻39 is set to “0” Zone List 2 can be used for other purposes.

UL This option is not for use in UL installations.

DIALER PROGRAMMING (✻40– ✻53) In fields ✻40, ✻41, ✻42, enter up to the number of digits shown.

Enter 0–9; #+11 for '

✻

'; #+12 for '#'; #+13 for a pause.

4040

PABX ACCESS CODE

PABX ACCESS CODEPABX ACCESS CODE

PABX ACCESS CODE

PABX/Call Waiting Disable

Enter up to 6 digits if PABX is needed to access an outside line. To clear entries from

field, press ✻40✻ OR

Enter“# + 11+ 7+ 0” to program touch-tone sequence “✻70” and cancel call waiting.

4141

PRIMARY

PRIMARY PRIMARY

PRIMARY

TEL

TEL TEL

TEL

NUM

NUMNUM

NUM

Primary Phone Number

Enter up to 20 digits; Do not fill unused spaces. If fewer than 20 digits entered, pressing

✻advances to the next field. To clear entries from field, press ✻41✻.

4242

SECOND

SECOND SECOND

SECOND

TEL

TELTEL

TEL

NUM

NUM NUM

NUM

Secondary Phone Number

Enter up to 24 digits; Do not fill unused spaces. If fewer than 24 digits entered, pressing

✻advances to the next field. To clear entries from field, press ✻42✻.

All four digits of the subscriber account number must be entered in Fields

✻

✻✻

✻

43 and

✻

✻✻

✻

44.

If ten digit format is selected

✻

✻✻

✻

48 (option 5), all ten digits of the Subscriber Account number must be entered.

In fields ✻43, ✻44, enter 4 to 10 digits. Enter 0–9; #+11 for B; #+12 for C; #+13 for D; #+14 for E; [#+15 for F].

Enter ✻ as 4th digit, if 3+1 dialer reporting is to be used. If only 3 digits used, pressing ✻advances to the next

field. Enter [✻] as the fifth digit if a 4-digit account number (for 4+1, 4+2, CID®) is used. To clear entries from

field, press ✻43✻ or ✻44✻.

Examples:

For Acct. 1234, enter: 1 | 2 | 3 | 4 ; For Acct. B234, enter: #+11| 2 | 3 | 4

For Acct. 1234567890, enter: 1| 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 ; For Acct. 123, enter: 1 | 2 | 3 | ✻

4343

PRIMARY

PRIMARY PRIMARY

PRIMARY

ACCOUNT

ACCOUNTACCOUNT

ACCOUNT

Primary Subscriber Account Number

See note above.

4444

SECNDRY

SECNDRYSECNDRY

SECNDRY

ACCOUNT

CCOUNTCCOUNT

CCOUNT

Secondary Subscriber Account Number

See note above.

† Entering a number other than the one specified may give unpredictable results.

- 6 -

Data Field Display Function& Programming Options [ ] = Programmed Table 1 Default Values

4646

FOLLOW ME PHONE

FOLLOW ME PHONEFOLLOW ME PHONE

FOLLOW ME PHONE

“Follow Me” Reminder Phone Number

Enter up to 24 digits; Do not fill unused spaces. If fewer than 24 digits entered, pressing ✻

advances to the next field. To clear entries from field, press ✻46✻.

Enter 0-9, #+11 for ‘✻’; #+12 for ‘#’; #+13 for a pause (two seconds).

PHONE SYS SELECT

PHONE SYS SELECTPHONE SYS SELECT

PHONE SYS SELECT

Phone System Select

† [5]

Central

Dialing

Mode

Station Pulse Tone Pulse Tone

No WATS 0 = No Speaker

Phone

1 = No

Speaker Phone

4 = With

Speaker

Phone

5 = With

Speaker Phone

WATS 2 = No Speaker

Phone

3 = No

Speaker Phone

6 = With

Speaker Phone

7 = With

Speaker Phone

4848

REP FRMT PRI/

REP FRMT PRI/REP FRMT PRI/

REP FRMT PRI/SEC

SECSEC

SEC

Report Format for Primary/Secondary

[7, 7]

Primary Secondary

0 = 3+1, 4+1 ADEMCO L/S STANDARD

1 = 3+1, 4+1 RADIONICS STANDARD

2 = 4+2 ADEMCO L/S STANDARD

3 = 4+2 RADIONICS STANDARD

5 = ADEMCO CONTACT ID® REPORTING

WITH 10-DIGIT SUBS ACCT NO.

6 or undefined = 4+2 ADEMCO EXPRESS

7 = ADEMCO CONTACT ID® REPORTING

WITH 4-DIGIT SUBS ACCT NO.

8 = 3+1, 4+1 ADEMCO L/S EXPANDED

9 = 3+1, 4+1 RADIONICS EXPANDED

4949

SPLIT/DUAL

SPLIT/DUAL SPLIT/DUAL

SPLIT/DUAL

REP

REPREP

REP

Split/Dual Reporting

[0]

To Primary Phone No.

0 = All reports

1 = Alarms, Restore, Cancel

2 = All except Open/Close, Test

3 = Alarms, Restore, Cancel

4 = All except Open/Close, Test

5 = All

To Primary Phone No.

6 = All reports except Open/Close

7 = All reports

8 = All reports

9 = All reports except Open/Close

To Primary Phone No.

10 = All except Open/Close

11 = All reports

12 = All reports

13 = All except Open/Close

To Secondary Phone No.

None, unless primary fails, then all

Others

Open/Close, Test

All

To Paging Number

Alarms, Open/Close‡, Troubles

Alarms, Troubles

Alarms, Open/Close‡, Troubles

Alarms, Troubles

To Follow Me System Phone Number)

Alarms, Open/Close‡, Troubles

Alarms, Troubles

Alarms, Open/Close‡, Troubles

Open/Close‡

‡ Will report users 0, 5-8 or wireless arm/disarm button zones 26-33; all other zones and users do not

report.

5050

ABORT WINDOW

ABORT WINDOWABORT WINDOW

ABORT WINDOW

Burglary Abort Window

† [2]

1 = 15-second abort window

2 = 30-second abort window

3 = 45-second abort window

SIA The sum of the burglary abort window entered in ✻50 and the entry delays entered in either Field

✻35 or ✻36 should not exceed 1 minute.

Note: The control validates the data entered in this field. If the selection is not valid the control emits a

single long beep indicating that the selection has been rejected. The control replaces the selection

with the default value “2”, which is displayed on the keypad, and advances to the next field.

Note: If you are using Pulse (rotary) Dialing, you must enter the

numbers slowly to allow the pulse dialer time to operate.

Note: Option 5 or 7 (ADEMCO Contact ID®)

must be selected for AAV.

- 7 -

Data Field Display Function& Programming Options [ ] = Programmed Table 1 Default Values

5151

PERIOD

PERIOD PERIOD

PERIOD

TEST

ESTEST

EST

REP

REP REP

REP

Periodic Test Report

(enter Test Code in field ✻64)

† [0]

0 = none; 1 = 24 hours; 2 = weekly; 3 = 30 days

5252

TEST

TEST TEST

TEST

REP

REP REP

REP

OFFSET

OFFSETOFFSET

OFFSET

First Test Report Offset

† [2]

0 = 24 hour; 1 = 6 hours; 2 = 12 hours; 3 = 18 hours

5353

SESCOA/RADIONICS

SESCOA/RADIONICSSESCOA/RADIONICS

SESCOA/RADIONICS

SESCOA/Radionics Select

[0]

0 = Radionics (0–9, B–F reporting);

1 = SESCOA (0–9 only reporting). Select 0 for all other formats.

5454

LACK

LACK LACK

LACK

OF OF

USAGE

USAGEUSAGE

USAGE

Lack of Usage Notification

[0]

0 = Disabled

1 = 1 day

2 = 7 days

3 = 27 days

4 = 90 days

5 = 180 days

6 = 365 days

5555

REPORT

REPORT REPORT

REPORT

CHANNELS

CHANNELSCHANNELS

CHANNELS

Reporting Channels

[0]

0 = Telco Line (no Radio)

1 = LRR/IP(Digital Communication only) and Telco Line

3 = LRR/IP (Digital Communication only) (no Telco Line)

5 = LRR/IP (Digital Communication with AAV) (Telco Line connections for 2-way voice

session only, if applicable)

FALSE AL

FALSE ALFALSE AL

FALSE ALA

ARM OPTS

RM OPTSRM OPTS

RM OPTS

False Alarm Options

[7]

Value Cancel Alarm Display

Auto Stay Arming

Exit Time Restart/Reset

0 = Disabled Disabled Disabled

1 = Disabled Disabled Enabled

2 = Disabled Enabled Disabled

3 = Disabled Enabled Enabled

4 = Enabled Disabled Disabled

5 = Enabled Disabled Enabled

6 = Enabled Enabled Disabled

7 = Enabled Enabled Enabled

Note: The control validates the data entered in this field. If the selection is not valid it will emit a single

long beep indicating that the selection has been rejected. The control replaces the selection

with the default value “7”, which is displayed on the keypad, and advances to the next field.

5858

RF RF

JAM

JAM JAM

JAM

DETECTION

DETECTIONDETECTION

DETECTION

RF Jam Detection

Note: For event logging option 2 must be selected.

[0]

0 = no RF Jam Detection; 1 = RF Jam Detect on, no CS report;

2 = RF Jam Detect on with CS report (if trouble/restore report is enabled in fields

✻

60,

✻

71)

† Entering a number other than the one specified may give unpredictable results.

TO PROGRAM SYSTEM STATUS, & RESTORE REPORT CODES (✻59–✻76, & ✻89):

With a 3+1 or 4+1 Standard Format: Enter a code in the first box: 1–9, 0, B, C, D, E, or F. Enter "#+10" for 0, "#+11" for B, "#+12" for C,

"#+13" for D, "#+14" for E, "#+15" for F.

A "0" (not "#+10") in the first box will disable a report.

A "0" (not "#+10") in the second box will result in automatic advance to the next field when programming.

With an Expanded or 4+2 Format: Enter codes in both boxes (1st and 2nd digits) for 1–9, 0, or B–F, as described above.

A "0" (not "#+10") in the second box will eliminate the expanded message for that report.

A "0" (not "#+10") in both boxes will disable the report.

With ADEMCO Contact ID Reporting: Enter any digit (other than "0") in the first box, to enable zone to report (entries in the second boxes

will be ignored). A "0" (not "#+10") in the first box will disable the report.

Examples: For Code 3(single digit), enter: 3 | 0

For Code 3 2 (two digits), enter: 3 | 2

For Code B 2 (Hexadecimal), enter: #+11 | 2

- 8 -

Data Field Display Function& Programming Options [ ] = Programmed Table 1 Default Values

SYSTEM STATUS REPORT CODES (✻59–✻68)

5959

EXIT

EXITEXIT

EXIT

ERROR

ERROR ERROR

ERROR

REP

REPREP

REP

Exit Error Report Code

[1]

6060

TROUBLE

TROUBLE TROUBLE

TROUBLE

REP

REP REP

REP

CODE

CODECODE

CODE

Trouble Report Code

[1,0]

6161

BYPASS

BYPASS BYPASS

BYPASS

REP

REP REP

REP

CODE

CODECODE

CODE

Bypass Report Code

[0,0]

6262

ACAC

LOSS

LOSS LOSS

LOSS

REP

REP REP

REP

CODE

CODE CODE

CODE

AC Loss Report Code

[0,0]

LOW

LOW LOW

LOW

BAT

BAT BAT

BAT

REP

REP REP

REP

CODE

CODECODE

CODE

Low Bat Report Code

[1,0]

TEST

TESTTEST

TEST

REP

REPREP

REPORT

ORTORT

ORT

CODE

CODE CODE

CODE

Test Report Code

[1,0]

6565

OPEN

OPEN OPEN

OPEN

REPORT

REPORT REPORT

REPORT

CODE

CODECODE

CODE

Open Report Code

†† [0]

6666

AWAY/STAY

AWAY/STAY AWAY/STAY

AWAY/STAY

REP

REPREP

REPORT

ORTORT

ORT

Arm Away/Stay Report Code

†† [0,0]

AWAY STAY

RF RF

TRANS

TRANSTRANS

TRANS

LB LB

REP

REPREP

REP

RF Transmitter Low Battery Report Code

[1,0]

6868

CANCEL

CANCEL CANCEL

CANCEL

REP

REP REP

REP

CODE

CODECODE

CODE

Cancel Report Code

[1,0]

6969

RECENT CLOSE REP

RECENT CLOSE REPRECENT CLOSE REP

RECENT CLOSE REP

Recent Close Report Code

| [1]

Note: The control validates the data entered in this field. If the selection is not valid the control will

emit a single long beep indicating that the selection has been rejected. The control replaces

the selection with the default value “1”, which is displayed on the keypad, and advances to the

next field.

RESTORE REPORT CODES (✻70–✻76)

ALARM

ALARM ALARM

ALARM

RES

RESRES

RES

REPORT

REPORT REPORT

REPORT

Alarm Restore Report Code

[1]

TROUBLE RES REP

TROUBLE RES REPTROUBLE RES REP

TROUBLE RES REP

Trouble Restore Report Code

[1,0]

BYPASS RES REP

BYPASS RES REPBYPASS RES REP

BYPASS RES REP

Bypass Restore Report Code

[0,0]

AC R

AC RAC R

AC RESTORE REP

ESTORE REPESTORE REP

ESTORE REP

AC Restore Report Code

[0,0]

(†† 2nd digit is automatically sent as the user

number if expanded or 4+2 reporting is selected.)

2nd digit is automatically sent as 2nd digit of the zone alarm report

code programmed in

✻

56, if expanded or 4+2 reporting is selected.

2nd digit is automatically sent as 2nd digit of the

zone alarm report code programmed in

✻

56, if

expanded or 4+2 reporting is selected.

- 9 -

Data Field Display Function& Programming Options [ ] = Programmed Table 1 Default Values

LO LO

BAT

BATBAT

BAT

RES

RES RES

RES

REP

REP REP

REP

Low Bat Restore Report Code

[1,0]

RFRF

LOBAT

LOBAT LOBAT

LOBAT

RES

ESES

REP

REP REP

REP

RF Transmitter Low Battery Restore Report Code

[1,0]

TEST

TEST TEST

TEST

RES

RES RES

RES

REPORT

REPORTREPORT

REPORT

Test Restore Report Code

[1,0]

DYNAMIC SIGNALING FIELD (✻77)

DYNAMIC SIG OPTS

DYNAMIC SIG OPTSDYNAMIC SIG OPTS

DYNAMIC SIG OPTS

Dynamic Signaling Options

| [0, 0]

1st Entry (delay before switch CS reporting path)

0 = Redundant

reporting on dialer

and LRR/IP device

1 = 15 seconds

2 = 30 seconds

3 = 45 seconds

4 = 60 seconds

5 = 75 seconds

6 = 90 seconds

7 = 105 seconds

8 = 120 seconds

9 = 135 seconds

#10 = 150 seconds

#11 = 165 seconds

#12 = 180 seconds

#13 = 195 seconds

#14 = 210 seconds

#15 = 225 seconds

2nd Entry

0 = Primary Dialer

Preferred Channel

1 = LRR/IP

Preferred Channel

2 = LRR/IP

reporting only

PROG TONE GEN TM

PROG TONE GEN TMPROG TONE GEN TM

PROG TONE GEN TM

Programmable Tone Generation Time

| [0, 0]

00 = Disabled

01-09 = 100-900 ms

10-99 = 1.0 – 9.9 secs

OUTPUT AND SYSTEM SETUP (✻80, ✻81, ✻83–✻85) See Procedures later in this manual.

8686

MULTI

MULTIMULTI

MULTI-

-MODE

MODE MODE

MODE

EMAILEMAIL

Multi-Mode (E-Mail Notification) (RIS is always enabled)

[0]

0 = Disable multi-mode devices (RIS enabled)

1 = Enable multi-mode device address #6 only (RIS enabled)

2 = Enable multi-mode device address #7 only (RIS enabled)

3 = Enable multi-mode addresses (RIS enabled)

AUX

AUX AUX

AUX

FUNC

FUNCFUNC

FUNC

1BTN

1BTN 1BTN

1BTN

PG PG

Aux Function/ 1-Button Paging

[0]

0 = Aux key performs defined function (macro);

1 = Aux key sends message to pager or voice message to follow me system phone no.

If 1, you must also select an option 6-9 in field ✻49 for the pager or 10-13 for the follow me

system announcement.

8888

PAGER CHARACTERS

PAGER CHARACTERSPAGER CHARACTERS

PAGER CHARACTERS

Pager Characters

Up to 16 digits can be entered that will appear in front of the 7-digit pager message sent by

the control. Refer to the Installation Instructions (fields ✻87, ✻88 and ✻49) for full

descriptions of the paging feature. You do not need to fill all 16 digits (press [✻] to

advance to next field).

To clear entries, enter ✻88✻. To enter “✻” = [#] + [11]; To enter “#” = [#] + 12]; To

enter 2-second pause = [#] + [13] (some pagers require an additional delay [pause] in

order to receive the entire message)

8989

EVNT

EVNT EVNT

EVNT

LOG

LOG LOG

LOG

80%

80% 80%

80%

REP

REPREP

REP

Event Log 80% Full Report Code

[0,0]

- 10 -

Data Field Display Function& Programming Options [ ] = Programmed Table 1 Default Values

9090

EVNT LOG OPTIONS

EVNT LOG OPTIONSEVNT LOG OPTIONS

EVNT LOG OPTIONS

Event Logging

Note: System messages are logged when

any non-zero selection is made.

[3]

0 = None; 1 = Alarm/Alarm Restore; 2 = Trouble/Trouble Restore; 4 = Bypass/Bypass

Restore; 8 = Open/Close.

Example: To select “Alarm/Alarm Restore”, and “Open/Close”, enter 9 (1 + 8); To select

all, enter #15.

9191

AAV/REM

AAV/REMAAV/REM

AAV/REM

PHN

PHN PHN

PHN

CTRL

CTRLCTRL

CTRL

Alarm Audio Verification (AAV)/Remote Phone Control

[2]

0 = None

1 = AAV and remote phone control

2 = remote phone control only

4 = AAV only

Notes: (1) In order to activate the Remote Phone Control feature and defeat an answering machine,

ensure that the correct ring detection count (“15”) has been programmed in field ✻95.

(2) Remote phone session will be terminated if a report must be sent.

(3) Alarm Audio Verification will only function when Contact ID® is selected. AAV cannot be

used for UL installations.

(4) If an alarm will be reported to primary and secondary phone numbers, AAV can only

function via the secondary number.

(5) If an alarm will be reported to a follow me phone number (10-12 in field ✻49) AAV cannot

be used.

(6) If AAV is selected and LRR/IP communications device is enabled, you must enter "0"

(primary dialer preferred channel) as the second entry in Field ✻77.

9292

SWINGER SHUTDOWN

SWINGER SHUTDOWNSWINGER SHUTDOWN

SWINGER SHUTDOWN

Swinger Shutdown

[1]

1 = shutdown after one alarm; 2 = shutdown after two alarms

Note: The control validates the data entered in this field. If the selection is not valid the control will

emit a single long beep indicating that the selection has been rejected. The control replaces

the selection with the default value “1”, which is displayed on the keypad, and advances to

the next field.

DOWNLOAD INFORMATION (✻93–✻95)

9393

FLEXBLE

FLEXBLE FLEXBLE

FLEXBLE

CALLBACK

CALLBACKCALLBACK

CALLBACK

Flexible Callback

[0]

0 = No flexible callback; 1 = Last digit flexible;

2 = Last 2 digits flexible; 3 = Last 3 digits flexible

9494

DOWNLOAD

DOWNLOAD DOWNLOAD

DOWNLOAD

PHONE

PHONEPHONE

PHONE

Download Phone Number

Note: In UL installations, downloading may only be performed if a technician is at the site.

Enter up to 20 digits, 0–9; #+11 for '✻'; #+12 for '#'; #+13 for a pause. Do not fill unused

spaces. If fewer than 20 digits entered, pressing ✻advances to the next field. To clear

entries from field, press ✻94✻.

9595

RING

RING RING

RING

DET

DET DET

DET

COUNT

COUNTCOUNT

COUNT

Ring Detection Count for Downloading/Remote Phone Control Mode

[15]

0 = Disable Station Initiated Download

1–14 = number of rings

(1–9, [#]+10 =10, [#] +11 =11, [#] +12 =12, [#] +13 =13, [#] +14 =14);

15 = answering machine defeat ([#] +15 =15)

Inhaltsverzeichnis

Andere Safewatch Sicherheitssystem Handbücher

Safewatch

Safewatch Pro 3000EN Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung