SafTLite Stubby Bedienungsanleitung
WARRANTY AND
INSTRUCTION MANUAL
See us on the
Internet at:
www. saftlite.co
®
®®
®
Care and Operation of Your New
Stubby
®
Fluorescent Worklight
Read this manual before attempting to operate or service this unit
CAUTION
1. Do not use your Stubby® worklight in hazardous areas under UL specifications 335.
. Inspect cord regularly for damage and replace if necessary for user safety.
3. Do not submerge
4. When hanging reel on ceiling:
• By Hook: Close hook with pliers to prevent reel from falling down.
• By Bracket Pin: With reel in place, bend end of “L” shaped pin to prevent pin from
falling out.
• Read mounting instructions carefully before installing. (below)
5. See caution statement regarding the polarized plug on back page.
OPERATION AND MAINTENANCE
1. Plug the unit into a 1 0V AC outlet. The Stubby® power supply cord is UL listed and
meets OSHA standards.
. To start, depress and release switch in handle of worklight. The lamp will flicker as the
automatic starter lights the lamp. To turn off depress, and release again.
3. Disconnect the power supply before servicing.
4. Keep the unit free from grease and dirt by using a damp cloth with mild detergent, or
waterless hand cleaner. This removes dirt from scratches in the outer tube and will
provide the best light output at all times. If the tube is damaged or badly scratched, it is
easily replaced and is available as a replacement part. (see the back page for contact
information)
5. Do not use solvents such as gasoline to clean unit or cord as it makes the parts brittle.
Do not allow brake fluid to contact the outer tube as it will cause permanent damage.
6. Regular cleaning of cord will prolong cord life.
LAMP SPECIFICATIONS - Phillips PL13/41
The lamp in your new Stubby® has undergone an additional process to make it an improved
impact lamp. We recommend that you use only a genuine Stubby® lamp which can be
purchased from an authorized Stubby® dealer.
Ite
m
No. Part No. Description
Item
No. Part No. Description
1.
5000-0397
Sw itch Cap, Commercial
18.
5000-0040
"M" Grip (less magnet)
.
5000-0398
Sw itch Thumb Nut
19.
5000-0471
Hook Assembly (w ith clip)
3.
5000-0399
Plastic Sw itch Washer
0.
5000-1065
Magnet, 58#
4.
5000-0469
Sw itch Assembly (inlcudes: ,3,5,6,7)
1.
5000-0470
Pop Riv et
5.
5000-0 45
Pin Terminal, Female
.
5000-0466
Moisture Tight Clamp, Large, Each
6.
5000-0 44
Sleev e, Female
3.
5000-0467
Moisture Tight Clamp, Small, Each
7.
5000-0400
Connector, Closed End Insulated
4.
5000-6076
Cord, 5' Assembly , Black
8.
5000-040
Screw
5000-6077
Cord, 5' Assembly , Yellow
9.
5000-0403
Strain Relief
5000-6078
Cord, 50' Assembly , Black
10.
5000-0404
Lampholder
5000-6079
Cord, 50' Assembly , Yellow
11.
5000- 003
Lamp, 13 Watt, Rough Serv ice
5000-6080
Reel, 0' Assembly
1 .
5000-0459
Reflector, Stubby , 1 0V
5000-6081
Reel, 40' Assembly
13.
5000-0408
End Cap, Cord End, Yellow
5.
5000-6070
Cord, 5' SJTO, Yellow
5000-0464
End Cap, Cord End, Black
5000-6071
Cord, 5' SJTO, Black
14.
5000-046
End Cap, Sw itch End, Yellow
5000-607
Cord, 50' SJTO, Yellow
5000-0463
End Cap, Sw itch End, Black
5000-6073
Cord, 50' SJTO, Black
15.
5000-0465
Outer Tube
5000-610
Reel Cord, 0' SVT, Black
16.
5000-0460
Hanger, Spring Steel, Tw in, Yellow Tips
5000-6103
Reel Cord, 40' SJT, Yellow
5000-0461
Hanger, Spring Steel, Tw in, Black Tips
6.
5166-3516
Ballast, 13 w att Stubby
17.
5000-0409
Hanger, Steel, Single, Yellow Tips
7.
5166-3544
Ballast Box & Lid (w /4 screw s), Yellow
5000-0468
Hanger, Steel, Single, Black Tips
5000-0119
Ballast Box & Lid (w /4 screw s), Black
all items in dotted lines
cord only L /
ballast
reel only L /
ballast
NOTE: omplete Replacement Headkits are Available. Please all the Phone Number on
the Back of this Manual for More Information.
PARTS LIST AND
If this Stubby® worklight malfunctions or is in need of repairs, send to:
General Manufacturing, Inc.
1100 S. Morgan St.
Bluffton, IN 46714
Phone: 260-824-3440 • Fax: 260-824-3448 • Internet: www.saftlite.com
"AUTION, IMPORTANT SAFETY INSTRU TIONS - This portable lamp has a polarized plug
(one blade is wider than the other) as a feature to reduce the risk of electric shock. This plug will
fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician. Never use an extension cord unless plug can be
fully inserted. Do not alter the plug."
"ATTENTION,INSTRU TIONS IMPORTANTES DE SE URITE -CETTE LAMPE PORTATIVE A
UNE FICHE POLARISANTE (UNE LAME EST PLUS GRANDE QUE L'AUTRE) COMME
CARACTERISTIQUE POUR REDUIRE LE RISQUE DE CHOC ELECTRIQUE. CETTE FICHE
N'ENGAGE Q'UNE PRISE POLARISANTE. SI LA FICHE N'ENGAGE PAS COMPLETEMENT
LA PRISE, ALORS RENVERSER LA, SI ELLE N'ENGAGE TOUJOURS PAS, METTER VOUS
EN RAPPORT AVEC UN ELECTRICIEN QUALIFIE. NE JAMAIS UTILISER AVEC UN
PROLONGATEUR SI LA FICHE N'ENGAGE PAS COMPLETEMENT. NE CHANGER PAS LA
FICHE."
RELAMPING INSTRUCTIONS
1. DIS ONNE T THE UNIT FROM ITS POWER SOUR E (UNPLUG).
. Lamp will be removed from cord end so it is not necessary to do anything at the switch
end.
3. Slide end cap down the cord about 6”. Remove the two screws that are now exposed.
4. The lamp assembly will now slide out the end of the tube. To assist in its removal, use a
pair of needle nose pliers to grip the square base of the lamp and pull. The bottom
lampholder will come out with the lamp.
5. Push the lamp through the lampholder with your thumb against the square base. It must
go out the front of the lampholder and the new lamp inserted the same way. Be sure the
wireways (two grooves in lampholder) are in the same position with respect to the new
lamp as they were with the lamp being removed.
6. Insert lamp with lampholder into tube being sure white wires from switch are in the
wireway groove. Using your thumb, push lamp and lampholder until it stops. (about 1/4”)
7. Re-plug terminal onto pins of lamp. Either terminal can go onto either pin.
8. Re-install end bracket and end cap in the same manner as when they were removed.
Re-install the two screws that were taken out in step 3. Re-lamping is now complete
90 Day Warranty
General Manufacturing Inc. warrants to the purchaser of this new light that it was
thoroughly tested and inspected and found to be in perfect working order before leaving
our factory. If within 90 days from the date of purchase, any part of this worklight proves
to be defective in material or workmanship, such defective part will be repaired or
replaced (company option) free of charge. The company's liability in all events is limited
to the purchase price paid.
The warranty does not apply to the fluorescent lamp nor does it apply to damage,
alteration, misuse or abuse not attributed to General Manufacturing, Inc., its
representatives, dealers or their employees. This warranty does not apply if the product
is mishandled or operated at a voltage exceeding, that shown on the reflector. This
warranty pertains to any light that may be termed by manufacturers, as a service unit.
General Manufacturing, Inc. has made a diligent effort to illustrate and describe the
products in its literature accurately, however such illustrations and descriptions are for
the sole purpose of identification and do not express or imply a warranty that the
products will necessarily conform to the illustrations or descriptions.
When returning product for warranty repair, please provide: from whom purchased,
date of purchase, and attach receipt or give invoice number.
Form No. 903 -7009 - Rev. 01/17/ 00
Dieses Handbuch passt für folgende Modelle
1
Andere SafTLite Arbeitsleuchte Handbücher
Beliebte Arbeitsleuchte Handbücher anderer Marken
PowerSmith
PowerSmith PWLD080T Bedienungsanleitung
MaxLite
MaxLite 73683 Bedienungsanleitung
Heitronic
Heitronic Trend 27867 Bedienungsanleitung
Monzana
Monzana Gore MZCL10 Bedienungsanleitung
EINHELL
EINHELL TE-CL 18/2000 LiAC Bedienungsanleitung
Bayco
Bayco NIGHTSTICK Dual-Light Xtreme Lumens... Bedienungsanleitung