Salus PL07 Bedienungsanleitung

Pump and Boiler Logic Module

Instruction Manual

Model No PL07

Salus PL07 Manual Ver007.qxd:Layout 1 10/9/10 10:02

PL07 INSTRUCTION MANUAL2

Salus PL07 Manual Ver007.qxd:Layout 1 10/9/10 10:03

PRODUCT COMPLIANCE

This product complies with the essential requirements of the following EC

Directives:

• Electro-Magnetic Compatibility Directive 2004/108/EC

• Low Voltage Directive 2006/95/EEC

• EC Marking Directive 93/68/EEC

SAFETY INFORMATION

These instructions are applicable to the Salus Controls model stated on the front

cover of this manual only, and must not be used with any other make or model.

These instructions are intended to apply in the United Kingdom only, and should

be followed along with any other statutory obligations.

This accessory must be fitted by a Competent person, and installation must

comply with the guidance provided in the current editions of BS7671 (IEE Wiring

Regulations) and Part ‘P’ of the Building Regulations. Failure to comply with the

requirements of these publications could lead to prosecution.

Always isolate the AC Mains supply before inserting or removing the unit from

the KL06 wiring centre, or carrying out any work on the PL07 logic module.

Please leave these instructions with the end user where they should be kept in a safe

place for future reference.

PL07 INSTRUCTION MANUAL 3

Salus PL07 Manual Ver007.qxd:Layout 1 10/9/10 10:03

PL07 INSTRUCTION MANUAL4

INTRODUCTION

The PL07 from Salus Controls is a modular pump and boiler logic control module,

designed specifically for heating applications.

FEATURES

• Modular installation

• Cage clamp wiring terminals (no terminal screws)

• Separate circulating pump and boiler control relays

• Volt free contacts

• User selectable pump run-on timer

• Auto shutdown in case of power failure

Salus PL07 Manual Ver007.qxd:Layout 1 10/9/10 10:03

INSTALLATION

Please read the important safety information at the start of this manual before

you begin to install the device.

NOTE: All electrical installation work should be carried out by a suitably

qualified Electrician or other competent person.

If you are not sure how to install this logic module consult either with a qualified

electrician, heating engineer or your boiler / heating system supplier for advice

on how to continue.

The PL07 logic module is not a standalone unit, and is intended to be mounted

on a KL06 wiring centre. The wiring centre should be installed first, followed by

the PL07 logic module.

To install the logic module, undo the securing screw on the wiring centre, insert

the logic module and then refit and tighten the securing screw.

The PL07 logic module should be mounted in a location where it will not come

into contact with water, moisture or condensation. The location should also be

accessible for the connection of mains and control wiring.

PL07 INSTRUCTION MANUAL 5

Salus PL07 Manual Ver007.qxd:Layout 1 10/9/10 10:03

There are few electrical connections

required to the PL07, and these

connections should be made to the

cage clamp terminals on the front of

the module (after first securing the

cable in the KL06 wiring centre):

PL07 INSTRUCTION MANUAL6

Terminal Marking Function

1 Common Contact (Boiler)

2 Normally Open Contact (Boiler)

3 Common Contact (Pump)

4 Normally Open Contact (Pump)

Salus PL07 Manual Ver007.qxd:Layout 1 10/9/10 10:03

CABLE CONNECTIONS

The PL07 does not use conventional screw terminals for wiring connections, but

uses cage clamp terminals. The cage clamp terminals are spring loaded and

provide a very quick and secure method of making all the electrical connections

to the module.

Please take the following steps to make the wiring connections to the PL07:

1. Prepare the cable ends:

• Strip outer sheath to a distance

of 110mm

• Strip 10mm from the ends of

each conductor sheath

It is very important that these

dimensions are followed to ensure

correct connection to the module.

2. Insert the cable into the cable grip:

3. Route the conductors through the wire guides:

PL07 INSTRUCTION MANUAL 7

110

Salus PL07 Manual Ver007.qxd:Layout 1 10/9/10 10:03

PL07 INSTRUCTION MANUAL8

4. Insert the conductors into their appropriate terminals:

Cable sizes used should be within the following ranges –

• Solid: 0.5 – 1.5mm2

• Stranded: 1.0 – 1.5mm2

If using stranded cable, a small screwdriver can be used

to open the cage clamp to allow conductor insertion.

5. Fit the protective cover:

Secure the cover by turning the locking screws a quarter turn.

ELECTRICAL SAFETY - The PL07 logic module should not

be operated without the protective cover in place.

Salus PL07 Manual Ver007.qxd:Layout 1 10/9/10 10:03

PL07 INSTRUCTION MANUAL 9

USER INTERFACE AND CONTROLS

The status and operation of the PL07 is clearly shown by the use of two green

Light Emitting Diodes (LEDs) on the module front panel:

When initially powering up the PL07, both LEDs will turn on for about one second

before turning off.

The LED indicators allow the user to see at a glance the current status of the logic

module. The only user adjustable settings for the PL07 are the mode jumper

settings, accessible from the front panel of the module:

Salus PL07 Manual Ver007.qxd:Layout 1 10/9/10 10:03

PL07 INSTRUCTION MANUAL10

JUMPER SETTING SUMMARY

Jumper Function Default Setting

J1 – Boiler and Pump Jumper in ON position

protection ON – OFF

OFF – Disables boiler

and pump protection

(immediately turns pump

and boiler relays on when a

thermostat calls for heat).

ON – Enables boiler and

pump protection (delays

turning on pump and boiler

relays for 3 minutes when

a thermostat calls for heat).

J2 – Pump overrun Jumper in ON (3

time ON – OFF minute) position

ON – After all thermostats

have switched off the pump

runs for an additional 3

minutes for boiler protection.

OFF – Disables pump over run.

When all thermostats are

switched off the pump will also

switch off immediately as well.

Salus PL07 Manual Ver007.qxd:Layout 1 10/9/10 10:03

Inhaltsverzeichnis

Andere Salus Computerhardware Handbücher

Salus

Salus KL04NSB Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung