Samson S-Split Bedienungsanleitung
One by Three Microphone Splitter
S Class Signal Processors
--
Table Of Contents
Introduction and Features 3
Front and Rear Panel Layout 4
Operating the S split
Setting Up the S split
5
Typical Set-up 6
Wiring Guide 7
Specifications 8
Copyright 2003, Samson Technologies Corp.
Printed June 2003
Samson Technologies Corp.
575 Underhill Blvd.
P.O. Box 9031
Syosset, NY 11791-9031
Phone: 1-800-3-SAMSON (1-800-372-6766)
Fax: 516-364-3888
www.samsontech.com
S split Introduction and Features
Introduction
Congratulations on your purchase of the S split by Samson Audio! The S split is a one-
by-three microphone splitter featuring a direct microphone through output, along with two
transformer isolated microphone outputs. The S split is a perfect solution for applications
where three sends from the same microphone are needed such as with a live recording
situation where a second feed is needed for connecting to a monitor mix console, and a
third to connect to a mic pre or recording console. Whatever your exact situation, the S
split will provide high quality and reliable performance thanks to its solid build construction
based around the extruded aluminum chassis and oversized rubber bumper feet.
In this manual, youʼll find a more detailed description of the features of the S split, as well
as a guided tour through the front and rear panels, step-by-step instructions for using the
S split, and full specifications. Youʼll also find a warranty card enclosed—please donʼt for-
get to fill it out and mail it so that you can receive online technical support and so we can
send you updated information about other Samson products in the future.
S Split Features
• One input by three output microphone/line splitter.
• 1 balanced XLR microphone input.
• 1 balanced direct output.
• 2 balanced transformer isolated outputs.
• Ground-lift switches for the two transformer isollated outputs.
• Large rubber bumper feet.
• Three year extended warranty.
3
S split Front and Rear Panel Layout
123
ABC
A DIRECT OUTPUT
- XLR balanced con-
nector output carrying the direct signal
from the Microphone input.
B ISOLATED OUTPUT 1
- XLR bal-
anced connector output carrying the
transformer isolated signal from the
Microphone input.
1 ISOLATION 2 GND LIFT
- When engaged
the ground from the Isolated Mic
Output 2 is disconnected.
2 BALANCED INPUT
- XLR balanced,
transformer isolated microphone input
for connecting the first microphone.
4
3 ISOLATION 1 GND LIFT
- When
engaged the ground from the
Isolated Mic Output 2 is discon-
nected.
Front Panel Layout
Rear Panel Layout
C ISOLATED OUTPUT 2
- XLR bal-
anced connector output carrying the
transformer isolated signal from the
Microphone input.
5
Operating the S split
Setting Up the S split
The basic procedure for setting up and using your S split is simple and takes only a few
minutes. Remove all packing materials (save them in case of need for future service).
There are many different ways to use the S split, however the basic connection is the
same in most installations and applications. The following example details the connection
for a microphone to a main PA mixer and also, to a separate monitor mixer, and a record-
ing console. Follow these simple steps to get connected.
• Using a standard XLR microphone cable, connect the your mic to the S splitʼs
BALANCED INPUT.
• Using another standard mic cable, connect the DIRECT OUTPUT to the main PA
mixer or stage box.
• Now, using another standard mic cable, connect the ISOLATED OUTPUT 1 to the
recording or monitor mix console.
• Finally, using another standard mic cable, connect the ISOLATED OUTPUT 2 to the
recording or monitor mix console.
Typical Set-up
The diagram below shows a typical set-up for live sound and recording, where the signal
from one microphone is split and sent to a recorder (with mic-pre input), a monitor mixer
and to the main front-of-house mixer.
6
Operating the S split
7
S split Wiring Guide
Wiring Guide
There are several ways to interface the S split, depending on your exact set-up. Follow the cable dia-
grams below for connecting your gear.
Samson Technologies Corp.
575 Underhill Blvd.
P.O. Box 9031
Syosset, NY 11791-9031
Phone: 1-800-3-SAMSON (1-800-372-6766)
Fax: 516-364-3888
www.samsontech.com
Frequency Response 10 Hz to 30kHz +/-3dB
Noise Level -110 dBu
Maximum Ouput Level Bal: +18 dBu
Max Input Level Bal: +22 dBu
Input Impedance
XLR: 10k Ohm
Output Impedance
XLR: 100 Ohm balanced
THD .003% Max
Noise Floor <-90 dBu
Dimensions 5.65” L x 4.13” W x 2” H (144mm L x 105mm
W x 51mm H)
Weight 16.5 oz., 419 gm.
S split Specifications
Inhaltsverzeichnis
Andere Samson Kabel und Steckverbinder Handbücher
