Samsung EH035CAV Bedienungsanleitung

ENGLISH

ESPAÑOL

FRANÇAIS

ITALIANO

PORTUGUÊS

DEUTSCH

H§

§E

E S F DB98-27564A(1)

EH035CAV

EH052CAV

EH070CAV

INSTALLATION

MANUAL

System Air Conditioner

(Cooling and Heating)

EH035EAV_IM_E_25807 4/6/06 2:30 PM Page 35

Safety Precautions

The following safety precautions must be taken when using your air conditioner.

◆The unit should not be installed by the user. Ask the dealer or authorized

company to install the units except room air conditioners for the U.S.A and

Canada area.

◆If the unit is installed improperly, water leakage, electric shock or fire may

result.

◆Mount with the lowest moving parts at least 2.5 m above the floor or grade

level. (If applicable)

◆The manufacturer does not assume responsibility for accidents or injury

caused by an incorrectly installed air conditioner. If you are unsure about

installation, contact an installation specialist.

◆When installing the built-in type air conditioner, keep all electrical cables

such as the power cable and the connection cord in pipe, ducts, cable

channels e.t.c to protect them against liquids, outside impacts and so on.

◆This appliance is not accessible to the general public. This appliance

should be installed according to the provided installation instruction.

WARNING

INSTALLING THE UNIT

◆If the power cord of this air conditioner is damaged, it must be replaced by

the manufacturer, its service agent or similarly qualified persons in order to

avoid a hazard.

◆The unit must be plugged into an independent circuit if applicable or

connect the power cable to the auxiliary circuit breaker. An all pole

disconnection from the power supply must be incorporated in the fixed

wiring with a contact opening of >3mm.

◆Do not use an extension cord with this product.

◆If the unit is equipped with a power supply cord and a plug, the plug must

be accessible after installation.

◆The air conditioner must be installed in accordance with national wiring

regulations and safety regulations wherever applicable.

POWER SUPPLY LINE,

FUSE OR CIRCUIT

BREAKER

• Risk of electric shock can cause injury or death. • Disconnect all remote

electric power supplies before servicing, installing or cleaning.

• This must be done by the manufacturer or its service agent or a similar

qualified person in order to avoid a hazard.

E-2

EH035EAV_IM_E_25807 3/24/06 7:21 PM Page 2

E-3

ENGLISH

■Deciding on Where to Install the Air Conditioner.................................................. 4

■Deciding on Where to Install the Indoor Unit........................................................ 6

■Indoor Unit Installation .......................................................................................... 8

■Purging the Unit ................................................................................................... 9

■Connecting the Refrigerant Pipe .......................................................................... 10

■Cutting/Flaring the Pipes ..................................................................................... 11

■Performing Leak Test & Insulation ........................................................................ 12

■Drain Pipe and Drain Hose Installation................................................................. 13

■Connecting the Connection Cord.......................................................................... 15

■Adjusting Air Flow ................................................................................................ 17

■Setting Up the Mode Option ................................................................................ 18

■Assigning Address to Indoor Unit ........................................................................ 21

■Additional Functions ............................................................................................. 22

■Filter Replacement (Optional) .............................................................................. 24

■Drain pump Installation(Optional) ....................................................................... 26

■Troubleshooting ................................................................................................... 28

■Parts list ............................................................................................................... 32

Contents

EH035EAV_IM_E_25807 3/24/06 7:21 PM Page 3

Deciding on Where to Install the Air Conditioner

When deciding on the location of the air conditioner with the owner, the following restrictions

must be taken into account.

Do NOT install the air conditioner in a location where it will come into contact with the following elements:

◆Combustible gases

◆Saline air

◆Machine oil

◆Sulphide gas

◆Special environmental conditions

If you must install the unit in such conditions, first consult your dealer.

E-4

Accessories

General

◆The following accessories are supplied with the indoor unit.

The type and quantity may differ depending on the specifications.

Installation

Manual

Insulation Cover

Pipe in

Insulation Drain

Insulation Cover

Pipe out

Insulation Cover

Drain Insulation Pipe in Insulation Pipe out

RubberCable-Tie Flexible hose Flexible hose clamp

User’s

manual

Cable-tie Cable clamp M4x16 tapped screw

Indoor unit power

drawing cable

Communication

cable of the wired

remote controller

Wire joint User’s

manual

Installation

Manual

Wired

remote controller

Wired Remote Controller Accessories

EH035EAV_IM_E_25807 3/24/06 7:21 PM Page 4

E-5

ENGLISH

Indoor Unit

5mm

◆There must be no obstacles near the air inlet and outlet.

◆Install the indoor unit on a ceiling that can support its weight.

◆Maintain sufficient clearance around the indoor unit.

◆Make sure that the water dripping from the drain hose runs away correctly

and safely.

◆The indoor unit must be installed in this way, that they are out of public

access. (Not touchable by the users)

◆After connecting a chamber, insulate the connection part between the indoor

unit and the chamber with t10 or thicker insulation. Otherwise, there can be

air leak or dew from the connection part.

Space Requirements for Indoor Unit

You must have 5mm or more space between the ceiling and the bottom of indoor unit.

Otherwise, the noise from the vibration of indoor unit may bother the user.

When the ceiling is under construction, the hole for check-up must be made to

take service, clean and repair the unit.

1398mm x 400mm or more

(A space for repair and service)

EH035EAV_IM_E_25807 3/24/06 7:21 PM Page 5

E-6

Deciding on Where to Install the Indoor Unit

938.4 Suspension position

1000 or more

Liquid pipe connection

Gas pipe connection

Hose connection

Power supply/Communicaion connection

Power supply connection

Air discharge grille flange

Air inlet grille flange

ø6.35 (1/4")

ø9.52 (3/8")

M8-M10

No. Name Remark

Drawing of the indoor unit

Unit : mm

8✕100=800

860 Air outlet duct flange

477 Suspension position

600

900

Service space

Inspection hole

22-ø3.2 Hole

All around

Discharge side

182

246

333

OD32

30.5

199

151.6

100

72.5 55

115.5

145.5

Suction side

11.9

71 100 10

3✕256=768

✴✴035✴✴

EH035EAV_IM_E_25807 3/24/06 7:21 PM Page 6

E-7

ENGLISH

Liquid pipe connection

Gas pipe connection

Drain pipe connection

Power supply connection

Air inlet grille flange

Air filter

Hook

ø6.35

ø12.70(✴✴052✴✴) / ø15.88(✴✴070✴✴)

OD32 ID26

Using drain pump (Optional)

For M8-M10

No. Name Remark

Unit : mm

✴✴052/070✴✴

EH035EAV_IM_E_25807 3/24/06 7:21 PM Page 7

E-8

Indoor Unit Installation

Ensure that the ceiling is strong enough to support

the weight of the indoor unit.

Before hanging the unit, test the strength of each attached

suspension bolt.

CCAA

AAUU

UUTT

TTII

IIOO

OONN

You must install the suspension bolts more than four

when installing the indoor unit.

CCAA

AAUU

UUTT

TTII

IIOO

OONN

Concrete

Suspension bolt(M8)-field supply

Hole in anchor

Hole in plug

Insert

Ceiling support

Rubber

Drain hose port

When the drain hose is installed to the right.

10mm

Mark the place to insert the suspension bolt where you want to install the

indoor unit.

Insert bolt anchors. Use existing ceiling supports or construct a suitable

support as shown in figure.

Install the suspension bolts depending on the ceiling type.

Screw eight nuts to the suspension bolts making space for hanging the

indoor unit. Make sure you have space for hanging the indoor unit.

Hang the indoor unit to the suspension bolts between two nuts.

Screw the nuts to suspend the unit.

Adjust level of the unit by using measurement plate for all 4 sides.

Refer to pages 6~7 for the dimension.

NNoo

oott

ttee

For proper drainage of condensate, give a 3mm slant to the left or

right side of the unit which will be connected with the drain hose,

as shown in the figure. Make a tilt when you wish to install the

drain pump, too.

NNoo

oott

ttee

Tubing must be laid and connected inside the ceiling when

suspending the unit. If the ceiling is already constructed, lay the

piping into position for connection to the unit before placing the

unit inside the ceiling.

NNoo

oott

ttee

EH035EAV_IM_E_25807 3/24/06 7:21 PM Page 8

E-9

ENGLISH

Purging the Unit

To prevent dirt or foreign objects from getting into the pipes during

installation, do NOT remove the pinch pipe completely until you

are ready to connect the piping.

NNoo

oott

ttee

On delivery, the indoor unit is loaded with refrigerant gas.

All this gas must therefore be purged before connecting

the assembly piping.

To purge the inert gas, proceed as follows.

Unscrew the pinch pipe at the end of each refrigerant pipe.

Result: All inert gas escapes from the indoor unit.

EH035EAV_IM_E_25807 3/24/06 7:21 PM Page 9

Connecting the Refrigerant Pipe

There are two refrigerant pipes of different diameters:

◆

A smaller one for the liquid refrigerant

◆

A larger one for the gas refrigerant

◆

The inside of copper tube must be clean & has no dust.

The connection procedure for the refrigerant pipes varies according to

the exit position of the pipes from the indoor unit, as seen when facing

the indoor in the “A” side.

◆

Liquid refrigerant port

◆

Gas refrigerant port

◆

Drain hose port

Remove the pinch pipe on the pipes and connect the assembly pipes to

each pipe, tightening the nuts, first manually and then with a torque

wrench, a spanner applying the following torque.

Must use insulator which is thick enough to cover the refrigerant tube to

protect the condensate water on the outside of pipe falling onto the floor

and the efficiency of the unit will be better.

Cut off any excess foam insulation.

Be sure that there must be no crack or wave on the bended area.

It would be necessary to double the insulation thickness(10mm or more)

to prevent condensation even on the insulator when if the installed area is

warm and humid.

If the pipes must be shortened refer to page 11.

NNoo

oott

ttee

Outer Diameter Torque (kgf•cm)

6.35 mm (1/4") 140~170

9.52 mm (3/8") 250~280

12.70 mm (1/2")

380~420

15.88 mm (5/8") 440~480

19.05 mm (3/4") 990~1210

22.23 mm (7/8") 990~1210

E-10

Liquid

refrigerant port

Drain hose

connection

port

Gas

refrigerant

port

Oil trap (Must be install

every 10m)

Oil trap (Must be install

every 10m)

Oil trap

(suction tube)

a. When the indoor unit is above the outdoor

unit

b. When the outdoor unit is above the indoor

unit

Indoor unit

Outdoor unit

Radius

5cm

Outdoor unit

EH035EAV_IM_E_25807 3/24/06 7:21 PM Page 10

Andere Handbücher für EH035CAV

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Samsung Klimaanlage Handbücher

Samsung

Samsung AC BN4PKG Series Bedienungsanleitung

Samsung

Samsung AC JNCDEH Series Bedienungsanleitung

Samsung

Samsung AM CXV Series Bedienungsanleitung

Samsung

Samsung AQV24PSBANXAX Bedienungsanleitung

Samsung

Samsung AP500PF Bedienungsanleitung

Samsung

Samsung AQ09T Series Leitfaden

Samsung

Samsung AM KN4DCH Series Bedienungsanleitung

Samsung

Samsung AQ12PGGE Bedienungsanleitung

Samsung

Samsung AG N1DEH Series Bedienungsanleitung

Samsung

Samsung AC030MXSCCC Bedienungsanleitung

Samsung

Samsung AR RXFP Series Bedienungsanleitung

Samsung

Samsung AQN09VFUAGM Bedienungsanleitung

Samsung

Samsung AS12SGGB Einrichtungshandbuch

Samsung

Samsung AQ12FAN Bedienungsanleitung

Samsung

Samsung AR18HSFNBWKNEU Bedienungsanleitung

Samsung

Samsung FH052EAMC Bedienungsanleitung

Samsung

Samsung MH FJEA series Bedienungsanleitung

Samsung

Samsung AJ FBMDEC Series Leitfaden

Samsung

Samsung AM056FN2DEH Series Bedienungsanleitung

Samsung

Samsung AC035MNADKH/EU Bedienungsanleitung

Samsung

Samsung AD19A1E07 Bedienungsanleitung

Samsung

Samsung AW0500 Einrichtungshandbuch

Samsung

Samsung MHXXXFJEA Series Bedienungsanleitung

Samsung

Samsung MCM-D201N Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Spheros

Spheros CC 355 Bedienungsanleitung

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Bedienungsanleitung

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

Hitachi

Hitachi RAS-E24CAK Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Hisense

Hisense 7K Technisches Handbuch

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung