Samsung DCS Compact Bedienungsanleitung

INSTALLATION MANUAL

CONTENTS

DCS

COMPACT

DIGITAL COMMUNICATION SYSTEM

SITE REQUIREMENTS

INSTALLING BASIC KSU AND

EXPANSION KIT

INSTALLING PRINTED CIRCUIT CARDS

POWER UP PROCEDURES

CONNECTING TELCO CIRCUITS

CONNECTING STATION EQUIPMENT

CONNECTING OPTIONAL EQUIPMENT

INSTALLING KEYSET DAUGHTER BOARD

CHANGING SOFTWARE

PART DESCRIPTION PAGE

1 SITE REQUIREMENTS .................................................................. 1-1

2 INSTALLATION OF BASIC KSU AND EXPANSION KIT

2.1 UNPACKING AND INSPECTION .......................................................... 2-1

2.2 KEY SERVICE UNIT INSTALLATION ................................................... 2-1

2.3 EXPANSION KIT INSTALLATION.......................................................... 2-1

2.4 GROUNDING ......................................................................................... 2-2

2.5 MDF CABLING .......................................................................................2-3

3 INSTALLING PRINTED CIRCUIT CARDS

3.1 RAM PACK .............................................................................................. 3-1

3.2 4 CO PROTECTION CARD ................................................................... 3-1

3.3 2 SLI CARD ............................................................................................. 3-1

3.4 MISC CARD............................................................................................. 3-1

3.5 4 TRK CARD............................................................................................ 3-1

3.6 6 DLI CARD............................................................................................. 3-1

3.7 6 SLI CARD.............................................................................................. 3-2

3.8 AA CARD ................................................................................................ 3-2

3.9 VDIAL CARD .......................................................................................... 3-2

3.10 AC15 CARD ............................................................................................ 3-2

3.11 BRI CARD................................................................................................ 3-2

3.12 2BRI CARD.............................................................................................. 3-2

4 POWER UP PROCEDURES

4.1 CONNECT POWER TO THE SYSTEM ................................................ 4-1

4.2 ROM CARD INDICATIONS .................................................................... 4-1

4.3 PCB VERIFICATION .............................................................................. 4-1

4.4 DEFAULT TRUNK AND STATION NUMBERING ................................. 4-1

SAMSUNG DCS INSTALLATION

TECHNICAL MANUAL TABLE OF CONTENTS APRIL 1996

TA B L E O F C O N T E N T S

5 CONNECTING TELCO CIRCUITS

5.1 SAFETY PRECAUTIONS ...................................................................... 5-1

5.2 LOOP START LINES .............................................................................. 5-1

5.3 OFF PREMISE EXTENSIONS (OPX) ................................................... 5-1

6 CONNECTING STATION EQUIPMENT

6.1 SAFETY PRECAUTIONS ...................................................................... 6-1

6.2 DCS COMPACT KEYSET ...................................................................... 6-1

6.3 ADD-ON MODULE ................................................................................. 6-1

6.4 SINGLE LINE TELEPHONE .................................................................. 6-1

6.5 DOOR PHONE AND DOOR LOCK RELEASE ..................................... 6-2

6.6 SIM (RS232C) .........................................................................................6-2

7 CONNECTING OPTIONAL EQUIPMENT

7.1 MUSIC ON HOLD/BACK GROUND MUSIC ......................................... 7-1

7.2 EXTERNAL PAGING .............................................................................. 7-1

7.3 COMMON BELL ..................................................................................... 7-2

7.4 RING OVER PAGE .................................................................................7-2

7.5 STATION MESSAGE DETAIL RECORDING (SMDR) .......................... 7-2

7.6 PC PROGRAMMING ............................................................................. 7-2

7.7 REMOTE PROGRAMMING ...................................................................7-3

7.8 POWER FAILURE TRANSFER (PFT) .................................................. 7-3

7.9 VOICE MAIL/AUTO ATTENDANT ......................................................... 7-4

8 INSTALLING KEYSET DAUGHTERBOARDS

8.1 KDB SLI .................................................................................................. 8-1

8.2 KDB DLI .................................................................................................. 8-1

8.3 CONNECTING TO THE KDB-S & KDB-D ............................................. 8-1

9 CHANGING SOFTWARE

9.1 ACCESSING THE EPROMS.................................................................. 9-1

9.2 REPLACING THE EPROMS .................................................................. 9-1

SAMSUNG DCS INSTALLATION

TECHNICAL MANUAL TABLE OF CONTENTS APRIL 1996

PART 1. SITE REQUIREMENTS

When planning the installation of the DCS COMPACT

, choose a site that meets the following requirements:

Select a location for the key service unit (KSU) that has enough space for easy installation and

has adequate lighting (see Figure 1–1).

Select a location that will minimize cable lengths. See the Cable Requirements table below.

The equipment should not be exposed to direct sunlight, corrosive fumes, dust, constant

vibration or strong magnetic fields such as those generated by motors and copy machines.

A direct commercial AC power outlet is required. Do not use extension cords.

Preferably, a dedicated circuit should be used to minimize the risk of other electrical equipment

being connected that could adversely affect system operation.

Ensure that all wires and cable going to and coming from the KSU are properly routed. Do not

cross fluorescent lights or run parallel with AC wires.

The equipment must be located in an environment that will maintain a temperature range of

– – and a humidity range of 10%–90% non-condensing.

Allow at least 6" clearance on both sides and 6" clearance on top of the KSU to ensure proper

ventilation.

Do not install in close proximity to a fire sprinkler head or other sources of water.

Meeting these requirements will help to ensure proper performance and greater life expectancy of

the system.

*This is the maximum distance a door phone can be from the DPIM. The DPIM can be a maximum

of 900 cable feet from the KSU.

SAMSUNG DCS INSTALLATION

TECHNICAL MANUAL APRIL 1996

1–1

CABLE REQUIREMENTS

EQUIPMENT CABLE AWG MAX FEET MAX METERS

DIGITAL KEYSETS 1PR. TWISTED 24 1300 400

ADD-ON MODULES 1PR. TWISTED 24 1300 400

SINGLE LINE STATION 1PR. TWISTED 24 3000 1 KM

DOOR PHONE 2PR. TWISTED 24 330* 100

SIM 1PR TWISTED 24 1300 400

SAMSUNG DCS INSTALLATION

TECHNICAL MANUAL APRIL 1996

1–2

FIGURE 1–1

KEY SERVICE UNIT DIMENSIONS

PART 2. INSTALLING OF BASIC KSU AND

EXPANSION KIT

2.1 UNPACKING AND INSPECTION

After unpacking the KSU, inspect for signs of physical damage. If any damage is detected, do not

attempt to install. Contact Samsung Technical Support Department.

Check to see that the KSU carton includes the following items:

Key service unit

4 Central Office Protection (4 COP) card

Wall-mount kit consisting of three screws

RAM pack

Check to see that the EXPANSION KIT carton includes the following:

Expansion backplane

Plastic card rack

Vinyl bag with screws and cables

2.2 KEY SERVICE UNIT INSTALLATION

The Key Service Unit (KSU) must be wall-mounted. The KSU should be mounted on a polywood

backboard at least 5/8" thick. Attach a mounting screw to the backboard . Next hang the KSU on the

screws and secure it to the backboard with the remaining two screws (see Figure 2–1).

2.3 EXPANSION KIT INSTALLATION

1. Mount the expansion backplane in the basic KSU and attach it securely with the five screws

supplied. Take care not to over-tighten the screws and damage the PCB (see Figure 2–2).

2. Connect the expansion backplane to the basic KSU by plugging one end of the ribbon cable into

the socket on the KSU motherboard and the other end into the expansion backplane.

NOTE:It is recommended that the ribbon cable be attached to the expansion baseboard before it is

installed in the KSU.

3. Connect the ground wires from the expansion backplane to the connectors on the KSU

motherboard.

4. Fit the plastic card rack to the basic KSU and secure with the three screws that are supplied. Take

care not to over-tighten the screws and strip the threads (see Figure 2–3).

SAMSUNG DCS INSTALLATION

TECHNICAL MANUAL APRIL 1996

2–1

2.4 GROUNDING

The DCS COMPACT comes equipped ready to use with a third wire AC ground provided through

the power cord. This third wire ground will be adequate for most applications. However, if it is

suspected that there is a problem with the ground provided at the AC outlet or local codes require a

solid earth ground to be connected to the KSU, the existing third wire ground must be disconnected

before power is applied. The existing third wire ground is disconnected by removing the holding

screw and taping and storing the wire (see Figure 2–4). After this wire has been disconnected, the

grounding lug on the PSU must be connected to a ground rod or metal cold water pipe using #10

AWG solid copper wire.

Failure to provide an adequate ground may cause confusing trouble symptoms or even circuit card

failure.

2.5 MDF CABLING

All connections to the DCS COMPACT system are made by way of a customer-provided main

distribution frame (MDF). The KSU and expansion kit are each connected to the MDF using a 25

pair female amphenol-type cable. These cables can be routed into the KSU cabinet from below.

Label each cable to correspond with the connector numbers (see Figure 2–4). Label each 66

terminating block with the same connector number with which the cable is labeled.

Use one pair twisted wire to cross-connect stations or lines to their associated port.

SAMSUNG DCS INSTALLATION

TECHNICAL MANUAL APRIL 1996

2–2

WARNING: Unplug the power cord from the AC outlet before attempting to connect the

ground. Hazardous voltage may cause death or injury. Observe extreme caution

when working with AC power.

SAMSUNG DCS INSTALLATION

TECHNICAL MANUAL APRIL 1996

2–3

FIGURE 2–1

KSU MOUNTING HOLES

SAMSUNG DCS INSTALLATION

TECHNICAL MANUAL APRIL 1996

2–4

FIGURE 2–2

LOCATION OF BACKPLANE

MOUNTING SCREWS

FIGURE 2–3

LOCATION OF RACK

MOUNTING SCREWS

SAMSUNG DCS INSTALLATION

TECHNICAL MANUAL APRIL 1996

2–5

FIGURE 2–4

KEY SERVICE UNIT GROUNDING

Andere Handbücher für DCS Compact

Inhaltsverzeichnis

Andere Samsung Konferenzsystem Handbücher

Samsung

Samsung SyncMaster VC240 Bedienungsanleitung

Samsung

Samsung SyncMaster VC240 Bedienungsanleitung

Samsung

Samsung SVMi-8 Bedienungsanleitung

Samsung

Samsung DCS Betriebsanleitung

Samsung

Samsung SIMATIC NET CP 5611 A2 Bedienungsanleitung

Samsung

Samsung iDCS500 Bedienungsanleitung

Samsung

Samsung iDCS500 Bedienungsanleitung

Samsung

Samsung DCS-816 Bedienungs- und Wartungsanleitung

Samsung

Samsung iDCS 16 Technisches Datenblatt

Samsung

Samsung OFFICESERV 500 Series Betriebsanleitung

Samsung

Samsung DCS 50si Bedienungsanleitung

Samsung

Samsung OfficeServ500 Bedienungsanleitung

Samsung

Samsung STN-WM55R Bedienungsanleitung

Beliebte Konferenzsystem Handbücher anderer Marken

Kramer

Kramer VIA GO Bedienungsanleitung

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Bedienungsanleitung

Sony

Sony PCS-I150 Bedienungsanleitung

Middle Atlantic Products

Middle Atlantic Products VTC Series Bedienungsanleitung

AVT

AVT MAGIC AC1 Go Bedienungsanleitung

Prentke Romich Company

Prentke Romich Company Vanguard Plus Leitfaden

Speakerbus

Speakerbus iD 712 Bedienungsanleitung

Trelleborg

Trelleborg SafePilot CAT PRO Bedienungsanleitung

Sennheiser

Sennheiser ADN Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 7100 Bedienungsanleitung

AINA

AINA PTT Voice Responder Bedienungsanleitung

Yamaha

Yamaha ProjectPhone PJP-100H Bedienungsanleitung

vissonic

vissonic VLI Series Bedienungsanleitung

Panasonic

Panasonic KX-VC500 Bedienungsanleitung

Poly

Poly Trio 8300 Bedienungsanleitung

Crestron

Crestron Mercury CCS-UCA-SMK Maßzeichnung

Tenveo

Tenveo ALL-IN-ONE Bedienungsanleitung

AXIWI

AXIWI AT-350 Bedienungsanleitung