Samsung P2570HD - SyncMaster - 24.6" LCD Monitor Bedienungsanleitung

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please

www.samsu ng.com/register

Model Serial No.

For more information on the operating procedures.

refer to the CD manual.

important Warranty information Regarding Television Format Viewing

[_ See the warranty card for more information onwarranty terms.

Wide screen format LCD Displays (16:9, the aspect ratio of the screen width to height) are primarily

designed to view wide screen format full-motion video. The images displayed on them should

primarily be in the wide screen 16:9 ratioformat, or expanded to fill the screen if your model offers

this feature and the images are constantly moving. Displaying stationary graphics and images

on screen, such as the dark sidebars on nonexpanded standard format television video and

programming, should be limited to no more than 5% of the total television viewing per week.

Additionally, viewing other stationary images and text such as stock market reports, video game

displays, station Iogos, web sites or computer graphics andpatterns, should be limited as described

above for all televisions. Displaying stationary images that exceed the above guidelines can cause

uneven aging of LCD Displays that leave subtle, but permanent burned-in ghost images in the LCD

picture. Toavoid this, vary the programming and images, and primarily display full screen moving

images, notstationary patterns or dark bars.

On LCD models that offer picture sizing features, use these controls to view different formats as a

full screen picture.

Be careful in the selection and duration of television formats used for viewing. Uneven LCD aging

as a result offormat selection and use, as well as burned-in images, are not covered by your

Samsung limited warranty.

Precautions When Displaying a Still Image

A still image may cause permanent damage to the TV screen

® Do not display a still image on the LCD panel for more than 2 hours as it can cause screen

image retention. This image retention is also known as "screen burn". Toavoid such image

retention, reduce the degree of brightness and contrast of the screen when displaying a still

image.

® Watching the LCD TV in 4:3 format for a long period of time may leave traces

of borders displayed on the left, right andcenter ofthe screen caused by the

difference of light emission on the screen.

Playing a DVD or a game console may cause a similar effect to the screen.

Damages caused by the above effect are not covered by the Warranty.

® Displaying still images from Video games and PCfor longer than a certain period of time may

produce partial after-images.

To prevent this effect, reduce the 'brightness' and 'contrast' when displaying still images.

CONTENTS

mAccessones................................. 2

[]Viewingthe ControlPanel ..................2

[]Viewinc theConnection Panel.....................3

= RemoteControl...........................................4

= InstallingBatteriesintheRemoteControl...........4

[] Configuringthe PictureMenu TVtAV,

Component/HDM] ]..................................15

mUsingYourTVas aComputer(PC)Display......t7

[] SettinguptheTV with your PC.................18

[] ConnectingVHF and UHFAntennas...........5

[] ConnectingCableTV ..................6

•, Connectinga DVD/Blu-Rayplayer/Satellite

receiver(Set-TopBox]viaHDMI.......................7 [] Configuringthe Setup Menu......................21

gConnectinga DVD/Blu-Rayplayer/Sateillte

receiver(Set-TopBox]viaDVl..........................8

[]Connectinga DVD/Blu-Rayplayer/Satellite

receiver(Set-TopBox)viaComponentcables.....8

[] Connectinga DigitalAudio System .............9

[] Connecunga PC.........................................9

[]TurningtheTV On andOff .........................11

[] Plug& PlayFea[ure...................... 11

[] Configuringthe Input Menu...................... 28

[] Configuringthe Support Menu...................27

[] ConnectingAnynet+ Devices....................28

[] SettingUpAnynet_....................................30

[] SwitchingbetweenAnynet+ Devices.........30

[] TroubleshootingforAnynet-. .....................32

[] ManagingChannels................. 13 [] Troubleshooting.........................................33

[] ChannelListOptionMenu (in All Channelsi[] WallMount KitSpecifications(VESA)....... 35

Added ChannelsIFavoritej ................13 [] UsingtheAnti-Theft KensingtonLock....... 35

=ChannelListOptionMenu(inProgrammed)......14 []Sr_ecifications............................................38

License

$R$(®)

Symbol

Note

TruSurround HD, SRS and (O) Symbol are trademarks of SRS Labs, inc.

TruSurround HD technology is incorporated under license from SRS Labs, Inc.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks

of Dolby Laboratories.

One-Touch Button TOOL Button

Accessories

Please make sure the following items are included with your LeD TV. If any items are missing,

contact your dealer.

Remote Control & Batteries (AAA x2) (Not available in all locations) tPower Cord tCleaning

C!oth /User Manua! (CD; Book)/Quick Setup Guide/Warranty Card (Not available in all

locations)/Cable holding ring/Stand Body/Stand Base

I_ The items color and shape may vary depending on the model.

I_ Cleaning Cloth is only provided for highly polished black products as a product feature.

Viewingthe ControlP=nel

I_ The product color an shape may vary depending on the model.

0 0 00000

O _/8: Toggles between all the available input sources. Inthe on-screen menu, use this

button as you use the button on the remote control.

MENU : Press to see an on-screen menu ofyour TV's features.

@,O - I+ : Moves from one menu item to another horizontally or adjusts selected menu values

Adjusts the audio volume.

_,_ v, ^ :Moves from one menu item to another vertically or adjusts selected menu values. InTV

mode, selects TV channels.

OdD(POWER): Press to turn the TV on andoff.

POWER INDICATOR: Blinks andturns offwhen the power ison and lights up in stand-by mode,

ViewingtheConnectionPanel

O[TV Rear Panel]

0 ¸_ .......

0e O •

[_ The product color and shape may vary depending on the model.

DVI=DIN

- Connects to the video jacks on your PC.

HDMIIPCIDVI=DAUDIO IN

- Connect the HDMI/PC/DVI-D AUDIO IN terminal at the back of your product to your

computer's sound card.

0 PCIN

0 ANT iN

Connects to the video jacks on your PC.

Connect your headphones to the Headphone connection terminal.

Connects to an antenna or cable TV system.

O POWER INPUT

- Connects the supplied power cord.

OHDMI IN

- Connects to the HDMI jack of a device with an HDMI output.

[_ No sound connection is needed for an HDMI to HDMI connection.

O COMPONENT IN

- Connect the port of the DVD, VCR (DVD /DTV Set-Top Box) to the [ R - AUDIO - L] port of

the product. Connect the VIDEO OUT port of the DVD/DTV Set-Top Box to the [PR,PB,Y]

input ports using a component video cable ( PR,PB,Y ).

0 DIGITAL AUDIO OUT (OPTICAL)

-Connects to a Digital Audio component.

@SERVICE

- Connector for service only.

AVIN- Video and audio inputs for external devices, such as a camcorder or VCR.

_i_ KENSINGTON LOCK

- The Kensington Lock (optional) is a device used to physically fix the system when used in

a public place. Ifyou want to use a locking device, contact the dealer where you purchased

the TV.

[_ The location of the Kensington Lock may be different depending on its model.

Remote Control

[_ You can use the remote control up to a distance of about 23 feet from the TV.

[_ The performance ofthe remote control may be affected by bright light.

[_ The product color an shape may vary depending on the model.

POWER:Turns the TV on and li_ TV: Selects the TV modeOoff. directly.

O NUMERIC BUTTONS: Press to t_) PRE-CH: This button

change the channel, is used to return to the

O-- :The "-" button operates only previous channel viewed.

for TV. It is used to select MMS @ MUTE _: Press to

(multi-channel) for a TV. temporarily cut off the

O VOL Jr-/VOL -- : Press to sound.

increase or decrease the _) ^ OH v : Press to change

volume, channels.

O CH LIST: Used to display @ SOURCE: Press to display

Channel Lists on the screen, and select the available

O TOOLS: Use to quickly select video sources.

frequently used functions. _iJ FAV.CH: Press to switch to

OUPMDOWNT/LEFT4/ your favorite channels.

RIGHT_./IB_: Use to select on- _) MENU rm : Displays the

screen menu items and change main on-screen menu.

menu values. _) RETURN: Returns to the

O INFO: Press to display previous menu.

information on the TV screen. _ EXIT:Pressto exit the

O COLOR BUTTONS: Use these menu.

buttons in the Channel list, etc. _ CC:Controlsthe caption

P.SmZE:Picturesize selection, decoder.

MTS:Press to choose stereo,

mono or Separate Audio

Program (SAP broadcast).

•_- _ -_

--©

Installing Batteries in the Remote Control

Lift the cover atthe back of the remote control upward as shown in the figure.

Install two AAA size batteries.

[_ Make sure to match the "+" and "-" ends of the batteries with the diagram

inside the compartment.

Replace the cover.

[_ Remove the batteries and store them in a cool, dry place if you won't be using the remote control

for a long time. (Assuming typical TV usage, the batteries should last for about one year.)

[_ If the remote control doesn't work, check the following:

® Is theTVpower on?

® Are the plus and minus ends of the batteries reversed?

® Are the batteries drained?

® Is there a power outage or is the power cord unplugged?

® Is there a special fluorescent light or neon sign nearby?

ConnectingVHFand UHFAntennas

Ifyour antenna has a set of leads that look like the diagram to the right, see 'Antennas with 300 £2

FlatTwin Leads' below.

Ifyour antenna has one lead that looks like the diagram to the

right, see 'Antennas with 75 £2Round Leads'.

Ifyou have two antennas, see 'Separate VHF and UHF

Antennas'.

Antennaswith 300QFiatTwinLeads

Ifyou are usingan off-air antenna (such as a roof antenna or

'rabbit ears') that has 3000 twin flat leads,follow the directions

below.

Place the wires from the twin leads under the screws ona 300-

75 O adapter (not supplied). Use a screwdriver to tighten the

screws.

2, Plug the adaptor into the ANT IN terminal onthe back of theTV.

Antennas with 75 _ Round Leads

Plug the antenna lead into the ANT IN terminal onthe back of

the TV.

SeparateVHFand UHFAntennas

Ifyou have two separate antennas for your TV (one VHF and

one UHF),you must combine the two antenna signals before

connecting the antennas to theTV. This procedure requires

an optional combiner-adaptor (available at most electronics

shops).

Connect both antenna leads to the combiner.

2, Plug the combiner into the ANT IN terminal onthe bottom of

the rear panel.

Connecting Cable TV

ToconnecttoacableTVsystem,followtheinstructionsbelow.

Cable without a Cable Box

Plug the incoming cable into the ANT iNterminal on the back of

the TV.

[_ Because this TV is cable-ready, you do not need a cable box

to view unscrambled cable channels.

Connectingto a CableBox thatDescramblesAll Channels

l, Findthe cable that is connected to theANT OUT terminal on

your cable box.

[_ This terminal might be labeled =ANTOUT', 'VHF OUT' or

simply, 'OUT'.

2. Connect the other end ofthis cable to the ANT iN terminal on

the back of theTV.

Connecting to a Cable Box that Desorambles Some Channels

Ifyour cable box descrambles only some channels (such as premium channels), follow the

instructions below. You will need a two-waysplitter, an RF (A/B) switch and four lengths of RF cable.

(These items are available at most electronics stores.)

Incoming cabJe _,__ _ _, "wRear

Splitter _ -- -- / RF(A/B) Switch

CabJeBox

1, Findand disconnect the cable that is connected to the ANT INterminal on your cable box.

[_ This terminal might be labeled 'ANT IN', 'VHF IN' or simply, 'IN'.

2. Connect this cable toa two-way splitter.

3, Connect an RF cable between the OUTPUT terminal on the splitter and the IN terminal on

the cable box.

4, Connect an RF cable between the ANT OUT terminal on the cable box andthe B-IN terminal

on the RF(A/B) switch.

5. Connect another cable between the other OUTterminal on the splitter and the A-IN terminal

on the RF (A/B) switch.

6. Connect the last RF cable between the OUTterminal on the RF (A/B) switch and the ANT iN

terminal on the rear of the TV.

After you have made this connection, set the A/B switch to the 'A' position for normal viewing. Set

the A/B switch to the 'B' position to view scrambled channels. (When you set theA/B switch to 'B',

you will need to tune your TV to the cable box's output channel, which is usually channel 3 or 4.)

Connectinga DVD!Blu-Rayplayer !Satellite receiver(Set-TopBox)via HDMI

This connection can only be made ifthere is an HDMI Output connector onthe external device.

DVD /Blu-Ray player ISatellite receiver

(Set-Top Box) Rear Panel TV Rear Panel

(Not supplied)

[_ What isHDMI?

® HDMl(High-Definition Multimedia Interface), is an interface that enables the transmission of

digital audio and video signals using a single cable.

® The difference between HDMI and DVI is that the HDMI device is smaller in size and has the

HDCP (High Bandwidth Digital Copy Protection) coding feature installed.

[_ Each DVD /Blu-Ray player /Satellite receiver (Set-Top Box) has a different back panel

configuration.

[_ The TV may not output sound and pictures may be displayed with abnormal color when DVD /

Blu-Ray player /Satellite receiver (Set-Top Box) supporting HDMI versions older than 1.3 are

connected. When connecting an older HDMI cable and there is no sound, connect the HDMI

cable to the HDMI INjack and the audio cables to the DVI-D INjacks on the back of the TV. If

this happens, contact the company that provided the DVD /Blu-Ray player /Satellite receiver

(Set-Top Box) to confirm the HDMIversion, then request an upgrade.

[_ HDMI cables that are not 1.3may cause annoying flicker or no screen display.

Connectinga DVD/Blu-Rayplayer/Satellitereceiver (Set-Top Box)via DVi

This connection can only be made if there is a DVI Output connector on the external device.

TV Rear Panel

DVD /Blu=Rayplayer /

Satellite receiver

(Set-Top Box)

RCA to stereo Cable (Not

DVI to HDMI Cable (Not supplied)

[_ Each DVD/Blu-Ray player /Satellite receiver (Set-Top Box) has a different back panel

configuration.

[_ When connecting a DVD /Blu-Ray player/Satellite receiver (Set-Top Box), match the

color ofthe connection terminal to the cable.

ConnectingaDVDtBlu-RayplayertSatellitereceiver(Set-TopBox)viaComponentcables

The rear panel jacks on your TV make it easy to connect a DVD /Blu-Ray player /Satellite receiver

(Set-Top Box) to your TV.

TV Rear Pane_

DVD /Biu-Ray player /

Satellite receiver

(Set-Top Box)

OAudio Cable (Not supplied)

OComponent Cable (Not supplied)

[_ Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and Pr (Red)

for enhanced video quality. Be sureto match the component video and audio connections. For

example, if connecting a Component video cable to COMPONENT IN, connect the audio cable

to COMPONENT IN also.

[_ Each DVD/Blu-Ray player /Satellite receiver (Set-Top Box) has a different back pane]

configuration.

[_ When connecting a DVD /Blu-Ray player/Satellite receiver (Set-Top Box), match the

color of the connection terminal to the cable.

Andere Handbücher für P2570HD - SyncMaster - 24.6" LCD Monitor

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Samsung LCD-Fernseher Handbücher

Samsung

Samsung LE32A65 A Series Bedienungsanleitung

Samsung

Samsung LE19B450C4W Bedienungsanleitung

Samsung

Samsung UN40JU6500 Bedienungsanleitung

Samsung

Samsung QE50LS03TAUXZT Bedienungsanleitung

Samsung

Samsung LE27T51B Bedienungsanleitung

Samsung

Samsung LCD TV Bedienungsanleitung

Samsung

Samsung LN26A450 Bedienungsanleitung

Samsung

Samsung LW15E13C Bedienungsanleitung

Samsung

Samsung LA22B352 Bedienungsanleitung

Samsung

Samsung AU8079 Bedienungsanleitung

Samsung

Samsung LN22D450 Bedienungsanleitung

Samsung

Samsung QE65QN800AU Bedienungsanleitung

Samsung

Samsung LW46G15W Bedienungsanleitung

Samsung

Samsung LE32S6 Bedienungsanleitung

Samsung

Samsung 6003 Bedienungsanleitung

Samsung

Samsung LN40C530 Bedienungsanleitung

Samsung

Samsung PRELIMINARY LN40B650 Bedienungsanleitung

Samsung

Samsung LN40D550 Bedienungsanleitung

Samsung

Samsung LA22N21B Bedienungsanleitung

Samsung

Samsung LN-R238W Bedienungsanleitung

Samsung

Samsung 6 series Bedienungsanleitung

Samsung

Samsung LW22N23N Bedienungsanleitung

Samsung

Samsung LN-T4053H Bedienungsanleitung

Samsung

Samsung UN46D7000 Betriebsanleitung

Beliebte LCD-Fernseher Handbücher anderer Marken

LG 32LC4R* Bedienungsanleitung

Dell

Dell W1900 19 Gebrauchsanweisung

Toshiba

Toshiba 57X3000A Bedienungsanleitung

Runco

Runco CX-52HD Bedienungsanleitung

Sharp

Sharp LC-32AX3H Bedienungsanleitung

Philips

Philips 47PFL7704D Bedienungsanleitung

Vizio

Vizio VO42LFHDTV10A Bedienungsanleitung

Philips

Philips 42PF7520D/79 Bedienungsanleitung

Insignia

Insignia NS-LCD32-09 Bedienungsanleitung

Sony

Sony WEGA KLV-27HR3 Bedienungsanleitung

Nexus

Nexus NX32031 Bedienungsanleitung

Zenith

Zenith Z32LC2D Bedienungsanleitung

Sony

Sony KDL-32S3000R - 32" Class Bravia S-series Digital Lcd... Bedienungsanleitung

Medion

Medion MEDION LIFE X14330 Bedienungsanleitung

Vizio

Vizio HDTV30A VW32L Bedienungsanleitung

Sharp

Sharp LC-24DV250K Bedienungsanleitung

SOYO

SOYO Dymond DYLT032A Bedienungsanleitung

Dynex

Dynex DX-L40-10A Kurzanleitung