Samsung SyncMaster 460UTn-2 Bedienungsanleitung
ii
LCD DISPLAY
quick start guide
460UTn-2, 460UT-2, 460UTn-B, 460UT-B
Introduction
Package Contents
Checking the Contents of the Package
Remove the lock from the package box, as shown in the figure above.
Lift up the package box by
holding the grooves on
both sides of the package
box.
Check the contents of the
package.
Remove the Styrofoam
and vinyl cover.
Note
•After unpacking the package, make sure to check the contents of the package.
• Store the packaging box in case you need to move the Product later.
• If any items are missing, contact your dealer.
• Contact a local dealer to purchase optional items.
• After unpacking, you may use the lower part of the package box as a temporary stand for
product test or operation check.
Unpacking
LCD Display
Manuals
Quick Setup Guide Warranty Card
(Not available in all loca-
tions)
User's Guide
Cables
Power Cord D-Sub Cable MagicInfo Software CD,
MagicInfo Manual CD
(Applicable to the
460UTn-2, 460UTn-B
model only)
Others
Remote Control
(BP59-00138B)
Batteries (AAA X 2)
(Not available in all loca-
tions)
Sold separately
Semi Stand KIT LAN Cable USB Cable
(Applicable to the
460UTn-2, 460UTn-B
model only)
Introduction
Sold separately
RGB to BNC Cable RGB to COMPONENT Ca-
ble
Network Box
(Applicable to the
460UT-2, 460UT-B model
only)
Wall Mount KIT TV Tuner Box
Your LCD Display
Front
SOURCE
button
Switches from PC mode to Video mode. Selects the input source that an
external device is connected to.
[PC] →[DVI] →[AV] →[Component] →[HDMI1] →[HDMI2] →[Display-
Port] →[MagicInfo] →[TV]
Note
•A TV tuner box (sold separately) must be connected to use the TV.
• A network box (sold separately) must be connected to use MagicInfo
with a 460UT-2, 460UT-B model.
POWER
button
Use this button for turning the LCD Display on and off.
Power indicator
Shows PowerSaver mode by blinking green
Introduction
Note
See PowerSaver described in the manual for further information regarding
power saving functions. For energy conservation, turn your LCD Display
OFF when it is not needed or when leaving it unattended for long periods.
Remote Control Sensor
Aim the remote control towards this spot on the LCD Display.
Rear
Note
See the "Connections" section for details about cable connections. The LCD Display's con-
figuration at the back may vary slightly depending on the model.
POWER S/W ON [
│
] / OFF
Switches the LCD Display On/Off.
POWER
The power cord plugs into the LCD Display
and the wall outlet.
IR OUT/IN
Receives a signal from the remote control
and outputs the signal through Loopout when
a removable sensor board is connected.
AMBIENT SENSOR IN
Supplies power to the removable sensor
board and receives a signal from the light
sensor.
DVI OUT (LOOPOUT)
•Connect a monitor to another monitor
through a DVI, DVI to HDMI cable.
Introduction
• Connect a DVI or DVI-HDMI cable to
[DVI
OUT (LOOPOUT)]
on the product and
[DVI IN]
or
[HDMI IN]
on another monitor.
• HDMI and network signals sent via the
[DVI OUT(LOOPOUT)]
port are dis-
played on the second display which has
the
[DVI IN]
port.
Note
•The Loopout function can be used to du-
plicate the screen of the primary display.
Connect
[DVI OUT]
on the primary dis-
play to
[DVI IN]
or
[HDMI]
on another
display.
• A maximum of 50 monitors can be con-
nected to DVI-Loopout (using a 2m-long
DVI cable). Up to Full HD resolution can
be supported. Compatible input sources
include DVI IN, HDMI IN 1, and HDMI IN
2 (MagicInfo).
RGB/COMPONENT IN (PC/COMPO-
NENT Connection Terminal (Input))
•Connect the
[RGB/COMPONENT IN]
port on the monitor to the RGB port on the
PC using the D-SUB cable.
• Connect the
[RGB/COMPONENT IN]
port on the monitor to the COMPONENT
port on the external device using the RGB
to COMPONENT cable.
• Connect the
[RGB/COMPONENT IN]
port on the monitor to the BNC port on the
PC using the RGB to BNC cable.
DVI IN (PC Video Connection Terminal)
Connect the
[DVI IN]
port on the monitor to
the DVI port on the PC using the DVI cable.
RGB/DVI/DP/HDMI AUDIO IN (PC/DVI/
DP/HDMI Audio Connection Terminal (In-
put))
Connect the
[RGB/DVI/DP/HDMI AUDIO
IN]
terminal of the monitor and the speaker
output terminal of your computer's sound
card using a stereo cable (sold separately).
DP IN
Receives a signal from the Display port.
Introduction
Connect a DP cable to
[DP IN]
on the product
and DP IN on another display.
AV/COMPONENT AUDIO IN [L-AUDIO-
R]
Connect the
[AV/COMPONENT AUDIO IN
[L-AUDIO-R]]
port on the monitor to the audio
output port on the PC or on the external de-
vice using an audio cable.
AV IN
Connect the
[AV IN]
terminal of your monitor
to the video output terminal of the external
device using a VIDEO cable.
AUDIO OUT
Connect a headphone or an External speak-
er.
DC OUT
Make sure to use connecting
[DC OUT]
ter-
minal to the authorized TV-Tuner Box
[SBB_DTC/ZA].
Otherwise, this may result in damage
to the product.
HDMI IN 1
•Connect the
[HDMI IN 1]
terminal at the
back of your LCD Display to the HDMI
terminal of your digital output device us-
ing a HDMI cable.
• Up to HDMI 1.3 can be supported.
Note
The
[HDMI IN 1]
port can be connected to
general external devices (DVD players, cam-
corders, etc.) or the TV set-top box.
HDMI IN 2 (MAGICINFO)
•Connect the
[HDMI IN 2 (MAGICINFO)]
terminal at the back of your LCD Display
to the HDMI terminal of your digital output
device using a HDMI cable.
• Up to HDMI 1.3 can be supported.
Introduction
Note
The MAGICINFO OUT port must be connec-
ted to the
[HDMI IN 2 (MAGICINFO)]
port.
RJ 45 MDC (MDC PORT)
MDC(Multiple Display Control) Program Port
Connect the LAN cable to
[RJ45 MDC]
on the
product and LAN on the PC. To use an MDC,
the MDC program must be installed on the
PC.
Note
Go to Multi Control and select RJ45 MDC as
the MDC Connection.
RS232C OUT/IN (RS232C Serial PORT)
MDC(Multiple Display Control) Program Port
Connect a serial cable (cross type) to
[RS232C]
on the product and RS232C on the
PC. To use an MDC, the MDC program must
be installed on the PC.
Note
Go to Multi Control and select RS232C
MDC as the MDC Connection.
RGB OUT
MagicInfo video output port
Note
Applicable to the 460UTn-2, 460UTn-B mod-
el only.
MAGICINFO OUT
Outputs MagicInfo HDMI signals. It should
be connected to
[HDMI IN 2 (MAGICINFO)]
via an HDMI cable.
LAN (LAN Connection Terminal)
Connects to a LAN cable to allow Internet or
network access in MagicInfo mode.
Note
Applicable to the 460UTn-2, 460UTn-B mod-
el only.
Introduction
USB (USB Connection Terminal)
Keyboard / Mouse, Mass Storage Device
Compatible.
Note
Applicable to the 460UTn-2, 460UTn-B mod-
el only.
Kensington Lock slot
A Kensington Lock is an anti-theft device that
enables users to lock the product so that they
can safely use it in public locations. Since the
shape and usage of the locking device may
differ depending on the model and the man-
ufacturer, for more information, refer to the
User Manual supplied with the locking device
for more information.
Note
You must purchase the Kensington Lock
separately.
To lock the product, follow these
steps:
1. Wrap the Kensington lock cable around
a large, stationary object such as a desk
or chair.
2. Slide the end of the cable with the lock
attached through the looped end of the
Kensington lock cable.
3. Insert the Kensington Lock into the se-
curity slot ( ) on the back of the dis-
play.
4. Lock the lock ( ).
Note
•These are general instructions. For exact
instructions, see the User Manual sup-
plied with the locking device.
• You can purchase the locking device
from an electronics store, an online shop,
or our service center.
Note
See the "Connections" section for details about cable connections.
Introduction
Remote Control
Note
The performance of the remote control may be affected by a TV or other electronic device
operating near the LCD Display , causing a malfunction due to interference with the frequen-
cy.
POWER
OFF
Number Buttons
DEL / GUIDE button
+ VOL -
SOURCE
D.MENU
TOOLS
Up-Down Left-Right buttons
INFO
PC/DVI/HDMI/DP
TTX/MIX
MTS/DUAL
ENTER/PRE-CH
MUTE
CH/P
TV
MENU
RETURN
EXIT
MagicInfo
POWER Turns the product On/Off.
OFF Turns the product Off.
Number Buttons Used to enter the password during the OSD adjustment or
to use MagicInfo.
Press to change the channel.
DEL / GUIDE button The "-" button is used to select Digital channels.
Electronic Program Guide (EPG) display.
- This function does not work for this LCD Display.
+ VOL - Adjusts the audio volume.
Introduction
Andere Handbücher für SyncMaster 460UTn-2
2
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere Samsung Monitor Handbücher
Samsung
Samsung SyncMaster S23A750D Benutzerhandbuch
Samsung
Samsung SyncMaster 210T Bedienungsanleitung
Samsung
Samsung Odyssey S49AG954NP Bedienungsanleitung
Samsung
Samsung 204B - SyncMaster - 20.1" LCD Monitor Kurzanleitung
Samsung
Samsung SyncMaster 153V Bedienungsanleitung
Samsung
Samsung 275T - SyncMaster - 27" LCD Monitor Bedienungsanleitung
Samsung
Samsung 920NW - SyncMaster - 19" LCD Monitor Bedienungsanleitung
Samsung
Samsung 2333HD - SyncMaster - 23" LCD Monitor Bedienungsanleitung
Samsung
Samsung T200HD - SyncMaster - 20" LCD Monitor Bedienungsanleitung
Samsung
Samsung SyncMaster 2243FW Bedienungsanleitung
Samsung
Samsung ME32C Bedienungsanleitung
Samsung
Samsung UltraView iAP-4000W Bedienungsanleitung
Samsung
Samsung U24E590D Bedienungsanleitung
Samsung
Samsung SYNCMASTER 932MP Bedienungsanleitung
Samsung
Samsung UD22B Bedienungsanleitung
Samsung
Samsung SyncMaster S24B750V Bedienungsanleitung
Samsung
Samsung HE40A Leitfaden
Samsung
Samsung 997MB - SyncMaster - 19" CRT Display Bedienungsanleitung
Samsung
Samsung SyncMaster 1100 DF Bedienungsanleitung
Samsung
Samsung PPM42M5H Bedienungsanleitung
