Samsung CLP 500 Bedienungsanleitung
AbsoluteCOLOR®• AbsoluteBLACK®• UniDrums • UniRollers • UniParts • UniCoatings
SAMSUNG CLP 500 - CARTRIDGE REMANUFACTURING INSTRUCTIONS
INCLUDING CARTRIDGE RESET SYSTEM FUSE INSTRUCTIONS
TONER CARTRIDGE
PAGE 2
CARTRIDGE RESET SYSTEM INSTRUCTIONS
PAGE 4
SAMSUNG CLP 500
COLOR LASER PRINTER
11124 Washington Blvd., Culver City, California U.S.A. 90232 Ph: 310 280-9620 • Fx: 310 838-7294 • [email protected]
© 2006 Uninet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
Uninet Imaging does not guarantee or warrant downloaded information.
USA
+310-280-9620
+310-838-7294
Ph:
Fx:
JAPAN
+81-3-44-55-2789
+310-838-7294
EUROPE
+34-93-757-1335
+34-93-741-4166
BRAZIL
+55-11-4822-3033
+55-11-4822-3353
ARGENTINA
+54-11-4571-2388
+54-11-4574-3706
www.uninetimaging.com
UNINET IMAGING INC. •SAMSUNG CLP 500 REMANUFACTURING INSTRUCTIONS
1. Remove the outer shell by first removing FIVE screws: FOUR
screws are located on the top of the cartridge as shown.
3. Remove the cover as shown. You will notice a small adhesive
holding it in place, but it will not be affected if the cover is
removed.
2. The FIFTH screw is located on the gear-side of the cartridge.
After removing the screws, unlock the bottom side of the shell by
pushing in the TABS shown using a flat-head screw driver.
REMOVING THE DEVELOPER ROLLER
4. Using a small flat-head screwdriver, remove the locking metal
CLIP located at each end of the developer roller axle. This clip
holds the axle gear in place. Push the clip out away from the axle
as shown.
NOTES:
11124 Washington Blvd., Culver City, California U.S.A. 90232 Ph: 310 280-9620 • Fx: 310 838-7294 • [email protected]
© 2006 Uninet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
Uninet Imaging does not guarantee or warrant downloaded information.
USA
+310-280-9620
+310-838-7294
Ph:
Fx:
JAPAN
+81-3-44-55-2789
+310-838-7294
EUROPE
+34-93-757-1335
+34-93-741-4166
BRAZIL
+55-11-4822-3033
+55-11-4822-3353
ARGENTINA
+54-11-4571-2388
+54-11-4574-3706
www.uninetimaging.com
TABS
2
1
3
4
5
UNINET IMAGING INC. •SAMSUNG CLP 500 REMANUFACTURING INSTRUCTIONS
5. Slide the developer roller gear off as shown.
7. Using a small flat-head screwdriver, push out the metal wash-
er-like ring that holds the axle in place near the toner fill plug
area. The other side should remain in place.
6. Remove the locking metal clip and gear from the opposite end
of the axle in the same manner as in Step 4 and 5.
8. Slip the developer roller outward then slide it away toward the
side of the cartridge.
11124 Washington Blvd., Culver City, California U.S.A. 90232 Ph: 310 280-9620 • Fx: 310 838-7294 • [email protected]
© 2006 Uninet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
Uninet Imaging does not guarantee or warrant downloaded information.
USA
+310-280-9620
+310-838-7294
Ph:
Fx:
JAPAN
+81-3-44-55-2789
+310-838-7294
EUROPE
+34-93-757-1335
+34-93-741-4166
BRAZIL
+55-11-4822-3033
+55-11-4822-3353
ARGENTINA
+54-11-4571-2388
+54-11-4574-3706
www.uninetimaging.com
NOTES:
UNINET IMAGING INC. •SAMSUNG CLP 500 REMANUFACTURING INSTRUCTIONS
9. Remove the toner fill plug to begin the cleaning process. Use
a vacuum on easy areas making sure there is nothing that will
vent. Use air pressure for hard-to-reach and sensitive areas.
10. After thoroughly cleaning the cartridge and installing clean
components, you are now ready to install your after-market toner.
11124 Washington Blvd., Culver City, California U.S.A. 90232 Ph: 310 280-9620 • Fx: 310 838-7294 • [email protected]
© 2006 Uninet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
Uninet Imaging does not guarantee or warrant downloaded information.
USA
+310-280-9620
+310-838-7294
Ph:
Fx:
JAPAN
+81-3-44-55-2789
+310-838-7294
EUROPE
+34-93-757-1335
+34-93-741-4166
BRAZIL
+55-11-4822-3033
+55-11-4822-3353
ARGENTINA
+54-11-4571-2388
+54-11-4574-3706
www.uninetimaging.com
NOTES:
REPLACING THE CARTRIDGE RESET SYSTEM FUSE
Samsung CLP 500, 550 Smartchip BK/C/M/Y Fuse
(Uninet part #8172)
NOTE: Electrical soldering is required for this section.
11. Locate the CONTACT ASSEMBLY on the gearless side of the
cartridge. Using a small flat-head screwdriver, carefully pry loose
the cartridge contacts assembly as shown.
UNINET IMAGING INC. •SAMSUNG CLP 500 REMANUFACTURING INSTRUCTIONS
12. Locate the FUSE that is soldered to the two outer contact
tabs.
14. Use the solder iron to smooth out any solder material remain-
ing on the outer contact tabs.
13. Use pliers to hold the FUSE while applying the heated solder
iron to the tab connected to it as shown. Carefully remove the
wire as the solder melts. Repeat the same on the other tab. DO
NOT OVERHEAT the tab as this may cause the housing to melt.
15. Solder the CARTRIDGE RESET SYSTEM FUSE onto the outer
contact tabs as shown. You can solder any side to either contact
as the tabs are not specific. Be careful not to overheat the tabs.
11124 Washington Blvd., Culver City, California U.S.A. 90232 Ph: 310 280-9620 • Fx: 310 838-7294 • [email protected]
© 2006 Uninet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
Uninet Imaging does not guarantee or warrant downloaded information.
USA
+310-280-9620
+310-838-7294
Ph:
Fx:
JAPAN
+81-3-44-55-2789
+310-838-7294
EUROPE
+34-93-757-1335
+34-93-741-4166
BRAZIL
+55-11-4822-3033
+55-11-4822-3353
ARGENTINA
+54-11-4571-2388
+54-11-4574-3706
www.uninetimaging.com
Remove
NOTES:
UNINET IMAGING INC. •SAMSUNG CLP 500 REMANUFACTURING INSTRUCTIONS
16. Insert the completed assembly back into the cartridge by lin-
ing up the tabs with the holes shown.
TESTING THE CARTRIDGE
18. Make sure the printer is turned OFF before installing and
testing the cartridge.
17. With the tabs in place, the assembly is now locked.
11124 Washington Blvd., Culver City, California U.S.A. 90232 Ph: 310 280-9620 • Fx: 310 838-7294 • [email protected]
© 2006 Uninet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
Uninet Imaging does not guarantee or warrant downloaded information.
USA
+310-280-9620
+310-838-7294
Ph:
Fx:
JAPAN
+81-3-44-55-2789
+310-838-7294
EUROPE
+34-93-757-1335
+34-93-741-4166
BRAZIL
+55-11-4822-3033
+55-11-4822-3353
ARGENTINA
+54-11-4571-2388
+54-11-4574-3706
www.uninetimaging.com
NOTES:
Andere Handbücher für CLP 500
4
Inhaltsverzeichnis
Andere Samsung Drucker Handbücher
Samsung
Samsung ML-3470 Bedienungsanleitung
Samsung
Samsung ML-3561N Series Bedienungsanleitung
Samsung
Samsung ML-3561N Series Bedienungsanleitung
Samsung
Samsung ML-3712ND Bedienungsanleitung
Samsung
Samsung ML-85G Bedienungsanleitung
Samsung
Samsung ProXpress M403 Series Bedienungsanleitung
Samsung
Samsung ML-1450 Series Bedienungsanleitung
Samsung
Samsung ML-1710 Bedienungsanleitung
Samsung
Samsung xpress C43x series Bedienungsanleitung
Samsung
Samsung ML 3050 - B/W Laser Printer Bedienungsanleitung
Samsung
Samsung Xpress M2020W Bedienungsanleitung
Samsung
Samsung Xpress C1810 series Bedienungsanleitung
Samsung
Samsung CLP 300 - Color Laser Printer Bedienungsanleitung
Samsung
Samsung Xpress M2875FD Bedienungsanleitung
Samsung
Samsung ELLIX-35II Bedienungsanleitung
Samsung
Samsung ML-2150 Bedienungsanleitung
Samsung
Samsung ML-1450 Series Bedienungsanleitung
Samsung
Samsung SCX-5315F Bedienungsanleitung
Samsung
Samsung ML-2955ND Bedienungsanleitung
Samsung
Samsung ML-6050 Bedienungsanleitung
