Samsung SRP - 350 Bedienungsanleitung
Operator’s Manual
All specifications are subjected to change without notice
SRP -350
RECEIPT PRINTER
2
Warning -U.S.
This equipment has been tested and found to comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates uses, and can radiate radio frequency energy and , if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own
expense.
Notice -Canada
This Apparatus complies with class “A” limits for radio interference as specified in the Canadian
department of communications radio interference regulations.
Get appareil est conforme aux normes class “A” d’interference radio tel que specifier par ministre
canadien des communications dans les reglements d’interference radio.
Caution
Some semiconductor devices are easily damaged by static electricity. You should turn the printer
“OFF”, before you connect or remove the cables on the rear side, in order to guard the printer
against the static electricity. If the printer is damaged by the static electricity, you should turn the
printer “OFF”.
INTRODUCTION
The SRP-350, SRP-350S, SRP-350P and SRP-350U Roll Printer are designed for use with
electronic instruments such as system ECR, POS, banking equipment, computer peripheral
equipment, etc.
The main features of the printer are as follows:
1. High speed printing : 35.5(1/6”Feed) lines per second.
2. Low noise thermal printing.
3. RS-232(SRP-350), RS-485(SRP-350S), Parallel(SRP-350P), USB(SRP-350U)
4. The data buffer allows the unit to receive print data even during printing.
5. Peripheral units drive circuit enables control of external devices such as cash
drawer.
6. Characters can be scaled up to 64 times compared to it’s original size.
7. Bar code printing is possible by using a bar code command.
8. Different print densities can be selected by DIP switches.
Please be sure to read the instruction in this manual carefully before using your new
SRP-350/SRP-350P.
NOTE : The socket-outlet shall be near the equipment and it
shall be easy accessible.
3
Table of Contents
CHAPTER 1. SETTING UP THE PRINTER.....................................4
1-1. UNPACKING ............................................................................ 4
1-2. CONNECTING THE CABLES ........................................................... 5
1-3. CONNECTING THE COMPUTER........................................................ 6
1-4. CONNECTING THE DRAWER.......................................................... 6
1-5. CONNECTING THE POWER SUPPLY.................................................. 7
1-6. INSTALLING OR REPLACING THE PAPER ROLL ..................................... 8
1-7. ADJUSTMENTS AND SETTINGS......................................................10
1-8. USING THE PRINTER .................................................................11
CHAPTER 2. HEXADECIMAL DUMPING.....................................14
CHAPTER 3. THE SELF TEST......................................................15
CHAPTER 4. CODE TABLE..........................................................16
CHAPTER 5. CONTROL COMMANDS LIST .................................24
APPENDIX.................................................................................27
A. STAR MODE COMMAND SUMMARY....................................................27
B. CONNECTORS............................................................................30
Interface Connector.................................................................31
Drawer Connector ...................................................................34
C. NOTES....................................................................................34
D. SPECIFICATION..........................................................................35
4
Chapter 1. Setting Up the Printer
1-1. Unpacking
Your printer box should include these items. If any items are damaged or missing,
please contact your dealer for assistance.
5
1-2. Connecting the Cables
You can connect up the three cables to the printer. They all connect to the connector
panel on the back of the printer, which is shown below:
Notes : Before connecting any of the cables, make sure that both the printer and the
host are turned off.
6
1-3. Connecting the computer
You need an appropriate interface cable.
1. Plug the cable connector securely into the printer’s interface connector.
2. Tighten the screws on both sides of the cable connector.
3. Attach the other end of the cable to the computer.
1-4. Connecting the Drawer
WARNING:
Use a drawer that matches the printer specification. Using an improper drawer may
damage the drawer as well as the printer.
CAUTION:
Do not connect a telephone line to the drawer kick-out connector; otherwise the
printer and the telephone line may be damaged.
Plug the drawer cable into the drawer kick-out connector on the back of the printer
next to the power supply connector.
7
1-5. Connecting the Power Supply
CAUTIONS:
When connecting or disconnecting the power supply from the printer, make sure that
the power supply is not plugged into an electrical outlet. Otherwise you may damage
the power supply or the printer.
If the power supply’s rated voltage and your outlet’s voltage do not match, contact your
dealer for assistance. Do not plug in the power cord. Otherwise, you may damage the
power supply or the printer.
1. Make sure that the printer’s power switch is turned off, and the power supply’s power
cord is unplugged from the electrical outlet.
2. Check the label on the power supply to make sure that the voltage required by the
power supply matches that of your electrical outlet.
3. Plug in the power supply’s cable as shown below. Notice that the flat side of the plug
faces down.
Notes : To remove the DC cable connector, make sure that the power supply’s power
cord is unplugged; then grasp the connector at the arrow and pull it straight out.
8
1-6. Installing or Replacing the Paper Roll
1. Make sure that the printer is not receiving data; otherwise, data may be lost.
2. Open the paper roll cover by pressing the cover-open button.
3. Remove the used paper roll core if there is one.
4. Insert the paper roll as shown.
Notes : Be sure to use paper rolls that meet the specifications. Do not use paper rolls
that have the paper glued to the core because the printer cannot detect the
paper end correctly.
Notes : Do not open the print cover while the printer is operating.
This may damage the printer.
9
5. Be sure to note the correct direction that the paper comes off the roll.
6. Pull out a small amount of paper, as shown. Then close the cover.
7. Tear off the paper as shown.
Notes : When closing the cover, press the center of printer cover firmly to prevent
Paper miss-loading.
10
1-7. Adjustments and Settings
The SRP-350 is set up at the factory to be appropriate for almost all users. It does,
however, offer some settings for users with special requirements.
It has DIP switches that allow you to change communication settings, such as
handshaking and parity check, as well as print density.
The SRP-350 also has a near-end sensor for the paper. This can give you a warning
when the paper is almost out. If you find that there is not enough paper remaining on
the roll when the near-end detector is triggered, you can change the near-end sensor
setting. Rotate the near end sensor tab at front or rear position.(See the below figure)
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Andere Samsung Drucker Handbücher
Samsung
Samsung SCX 4500W - Personal Wireless Laser Multi-Function... Bedienungsanleitung
Samsung
Samsung PROXPRESS C301X SERIES Bedienungsanleitung
Samsung
Samsung ProXpress M4530ND Bedienungsanleitung
Samsung
Samsung ML-5050G Series Bedienungsanleitung
Samsung
Samsung ML-4550 Series Bedienungsanleitung
Samsung
Samsung SPP-R200 Versionshinweis
Samsung
Samsung SCX-465x Series Bedienungsanleitung
Samsung
Samsung ML-2551N Bedienungsanleitung
Samsung
Samsung ML-2010 - B/W Laser Printer Bedienungsanleitung
Samsung
Samsung CLP 500 Bedienungsanleitung
Samsung
Samsung 500N - CLP Color Laser Printer Bedienungsanleitung
Samsung
Samsung ML-2250/XBG Bedienungsanleitung
Samsung
Samsung ML-5100A Bedienungsanleitung
Samsung
Samsung ML-4512ND Benutzerhandbuch
Samsung
Samsung CLP 610ND - Color Laser Printer Benutzerhandbuch
Samsung
Samsung ML-1200 Series Bedienungsanleitung
Samsung
Samsung ML 2510 - B/W Laser Printer Bedienungsanleitung
Samsung
Samsung CLP-775ND Bedienungsanleitung
Samsung
Samsung ML-1200 Series Betriebsanleitung
Samsung
Samsung ML-2150 Bedienungsanleitung
