Samsung NE58K9850WG Bedienungsanleitung

Electric Range

installation manual

imagine the possibilities

Thank you for purchasing this Samsung product.

Install_NE58H9970WS_AA_AC_DG68-00594A-05_EN+MES+CFR.indb 1 2017-08-11  6:28:40

contents

PREPARING TO INSTALL THE

RANGE

3 About this section

3 For your safety

4 Remove packaging

4 Prepare tools & Parts

5 Checking the installation site

7 To avoid breakage

CONNECTING THE POWER

8 Step 1. Meeting electrical

connection requirements

9 Step 2. Accessing the power cord

connection

10 Step 3. Installing the power cord

12 Step 4. Installing the conduit

15 Step 5. Replacing the access cover

INSTALLING THE RANGE

16 Installing the anti-tip device

18 Finalizing the installation

English - 2

Install_NE58H9970WS_AA_AC_DG68-00594A-05_EN+MES+CFR.indb 2 2017-08-11  6:28:40

preparing to install the range

ABOUT THIS SECTION

READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY.

Important note to the installer

• Read all instructions contained in these installation instructions before installing

the range.

• Remove all packing materials from the oven compartments before connecting the

electrical supply to the range.

• Observe all governing codes and ordinances.

• Be sure to leave these instructions with the consumer.

Important note to the consumer

Keep these instructions for the local electrical inspector’s use.

• As when using any appliance generating heat, there are certain safety precautions

you should follow.

• Be sure your range is installed and grounded properly by a qualiﬁed installer or

service technician.

• Make sure the wall coverings around the range can withstand the heat generated

by the range.

• To eliminate the need to reach over the surface elements, avoid having cabinet

storage space above the cooktop.

• The range should not be placed on a base.

FOR YOUR SAFETY

WARNING

WARNING If the information in this manual is not followed exactly, a

ﬁre or electrical shock may result causing property damage, personal injury, or death.

WARNING

WARNING Before beginning the installation, switch the power o at

the service panel and lock the service disconnecting switch to prevent power from being

switched on accidentally. When the service disconnecting switch cannot be locked,

securely fasten a prominent warning device, such as a tag, to the service panel.

WARNING

WARNING This appliance must be properly grounded.

English - 3

01 PREPARING TO INSTALL THE RANGE

Install_NE58H9970WS_AA_AC_DG68-00594A-05_EN+MES+CFR.indb 3 2017-08-11  6:28:40

REMOVE PACKAGING

Remove the packaging materials. Remove the supporter frame located on the back

of the cooktop glass. Failure to remove packaging materials could result in damage

to the appliance.

PREPARE TOOLS & PARTS

The tools you will need

Drill Adjustable Wrench Pliers 1/4" Nut Driver

Phillips Screwdriver Flat Screwdriver Pencil Level

What’s included with your range

Template Anti-Tip Bracket Screws (short:2 ea,

long:2 ea)

Filler Kit & Screws

(3 ea)

Additional materials you may need

4-Wire Cord or 3-Wire Cord

(UL Approved 40 or 50 AMP)

Strain Relief

(For Conduit Installation Only)

English - 4

Install_NE58H9970WS_AA_AC_DG68-00594A-05_EN+MES+CFR.indb 4 2017-08-11  6:28:40

CHECKING THE INSTALLATION SITE

Clearances and dimensions

To install the range, refer to the following ﬁgure.

CAUTION

CAUTIONThis range has been designed to comply with the maximum

allowable wood cabinet temperatures of 194 °F. Make sure the wall covering,

countertops, and cabinets around the range can withstand the heat (up to 194 °F)

generated by the range. If not, discoloration, delamination, or melting may occur.

SLIDE-IN CUTOUT FREESTANDING CUTOUT

36"~36-4/5"

31”

4-1/2"

23-1/5"

6-3/10"

24-7/10"

48"

28-3/5"

26-3/10"

29-4/5"

26-3/10"

Hatched Faces should

be ﬂat and leveled.

35-7/8"

23-3/16"

1/2" min.

25"

3" 24"

1" min.

6”

25”

3”

24” 3”

A : Cabinet opening min 30” (76.2 cm)

B : Acceptable electrical outlet area

If your cabinets are over 36-4/5” high, you must install this range on a hard, heat

resistant support that raises the surface of the range so that it is about even with

the countertop.

CAUTION

CAUTIONYou must use the rear ﬁller kit to install the range in a

freestanding cutout cabinet. For more information, see “Optional rear ﬁller kit” as shown

below.

Optional rear ﬁller kit

Used to ﬁll gap between the range back and wall. Adds a ﬁller strip to the rear of the

range. This kit can only be used when the opening in the countertop is 25” deep.

If the countertop depth is

greater than 25", there will

be a gap between the ﬁller kit

and the back wall.

English - 5

01 PREPARING TO INSTALL THE RANGE

Install_NE58H9970WS_AA_AC_DG68-00594A-05_EN+MES+CFR.indb 5 2017-08-11  6:28:40

Minimum dimensions

IMPORTANTTo eliminate the risk of burns or ﬁre caused by reaching

over heated surface units, avoid having cabinet storage space located above the surface

units. If you have cabinet storage space over the heating elements, you can reduce the

risk by installing a range hood that projects horizontally a minimum of 5 inches beyond

the bottom of the cabinets.

* 30"

30"

** 15"

* A minimum of 30" is required

between the top of the

cooking surface and the

bottom of an unprotected

wood or metal cabinet; a

minimum of 24" is required

if the bottom of the wood or

metal cabinet is protected

by not less than 1/4" of ﬂame

retardant millboard covered

with not less than no.28

MSG of sheet steel, 0.015"

of stainless steel, 0.024"

of aluminum, or 0.020" of

copper.

** A minimum of 15" is required

between the countertop and

the adjacent cabinet bottom.

English - 6

Install_NE58H9970WS_AA_AC_DG68-00594A-05_EN+MES+CFR.indb 6 2017-08-11  6:28:41

TO AVOID BREAKAGE

CAUTION

CAUTIONDo NOT lift or handle the unit by the cooktop glass.

Fig. 1

1. The counter top around the cut-out should be ﬂat and leveled (see hatched area on

Fig. 1).

2. Before installing the unit, measure the heights of the two cabinet sides (C1~C4),

front and back (See Fig. 1) from the ﬂoor to the top of the counter.

3. Level the range using the four leveling legs so that the height from the ﬂoor

to the underside of the cooktop glass frame is greater than the tallest cabinet

measurement by at least 1/16".

4. Remove the Support Frames on the back left and back right of the glass cooktop

(Refer to page 4).

5. Slide the unit into the cabinet (DO NOT PUSH THE UNIT HARD). Make sure the

center of the unit aligns with the center of the cabinet cut-out.

6. The cooktop glass frame under the cooktop glass MUST sit above the cabinet

countertop so the unit is supported by its leveling legs. The cooktop glass should

NOT directly touch the countertop If the cooktop glass is touching the countertop,

it could break, voiding the warranty.

IMPORTANTMAKE SURE the unit is supported by the leveling legs

and NOT by the cooktop itself. The cooktop glass must sit above the surface of the

countertops.

English - 7

01 PREPARING TO INSTALL THE RANGE

Install_NE58H9970WS_AA_AC_DG68-00594A-05_EN+MES+CFR.indb 7 2017-08-11  6:28:41

connecting the power

STEP 1. MEETING ELECTRICAL CONNECTION

REQUIREMENTS

CAUTION

CAUTIONFor personal safety, do not use an extension cord

with this appliance. Remove the house fuse or open the circuit breaker before

beginning installation.

This appliance must be supplied with the proper voltage

and frequency, and be connected to an individual, properly

grounded branch circuit, protected by a circuit breaker or fuse

having amperage as speciﬁed on the rating plate. The rating

plate is located above the drawer on the oven frame. (Fig. 1 or

Fig. 2)

We recommend you have the electrical wiring and hookup

of your range connected by a qualiﬁed electrician. After

installation, have the electrician show you where your main

range disconnect is located.

Check with your local utilities for electrical codes which apply

in your area. Failure to wire your oven according

to governing codes could result in a hazardous

condition. If there are no local codes, your range must

be wired and fused to meet the requirements of the

National Electrical Code, ANSI/NFPA No.

70–Latest

Edition. You can get a copy by writing:

National Fire Protection Association

Batterymarch Park

Quincy, MA 02269

Eective January 1, 1996, the National Electrical Code requires that new

construction (not existing) utilize a 4-conductor connection to an electric

range.

When installing an electric range in new construction, follow Steps 2 and 3

for a 4-wire connection.

You must use a 3-wire or 4-wire, single-phase A.C. 208Y/120 Volt or 240/120 Volt,

60 hertz electrical system.

If the electrical service provided does not meet the above speciﬁcations, have a

licensed electrician install an approved outlet.

Use only a 3-conductor or a 4-conductor UL-listed range cord. These cords may be

provided with ring terminals on the wire and a strain relief device.

(Fig. 1)

(Fig. 2)

English - 8

Install_NE58H9970WS_AA_AC_DG68-00594A-05_EN+MES+CFR.indb 8 2017-08-11  6:28:41

A range cord rated at 40 amps with 125/250 minimum volt range is required. A 50

amp range cord is not recommended but if used, it should be marked for use with

nominal 13⁄8" diameter connection openings. Care should be taken to center the

cable and strain relief within the knockout hole to keep the edge from damaging the

cable.

• Because range terminals are not accessible after the range is in position, a ﬂexible

service conduit or cord must be used.

NOTE If conduit is being used, go to Step 4 on page 12.

ALL NEW BRANCH-CIRCUIT CONSTRUCTIONS, MOBILE HOMES,

RECREATIONAL VEHICLES, AND INSTALLATIONS WHERE LOCAL

CODES DO NOT ALLOW GROUNDING THROUGH NEUTRAL,

REQUIRE A 4-CONDUCTOR UL-LISTED RANGE CORD.

STEP 2. ACCESSING THE POWER CORD CONNECTION

Loosen and then remove the rear access cover screw with a screwdriver. Remove

the rear access cover by lifting it up and then out. The terminal block will then be

accessible.

Access cover

Terminal block

Speciﬁed power-supply-cord kit rating

Range rating, watts Speciﬁed rating of

power-supply-cord

kit, amperes

Diameter (inches) of range

connection opening

120/240 volts

3-wire

120/208 volts

3-wire Power cord Conduit

8750 - 16500 7801 - 12500 40 or 50 A 13/8" 11/8"

For power cord installations, go to page 10. For conduit installations, go to page 12.

English - 9

02 CONNECTING THE POWER

Install_NE58H9970WS_AA_AC_DG68-00594A-05_EN+MES+CFR.indb 9 2017-08-11  6:28:42

STEP 3. INSTALLING THE POWER CORD

For power cord installations, hook the strain relief over the power cord hole (13/8")

located below the rear of the drawer body. Insert the power cord through the strain

relief and tighten the device.

Strain relief

Power cord

Conduit connection plate

• You must install the power cord with a strain relief.

• Attach the strain relief to the 13/8" opening in the conduit connection plate.

Installing a 3-wire power cord

WARNING

The neutral or ground wire of the power cord must be

connected to the neutral terminal located in the center of the terminal block. The power

leads must be connected to the lower left and the lower right terminals of the terminal block.

1. Remove the 3 lower terminal screws

from the terminal block.

Insert the 3 terminal screws through

each power cord terminal ring and into

the lower terminals of the terminal block.

Be certain that the center wire (white/

neutral) is connected to the center lower

position of the terminal block.

3. Tighten screws securely to the terminal

block. DO NOT remove the ground

strap connection.

4. Go to Step 5 on page 15 to continue

with the installation.

Ground strap

Neutral

terminal

Black

White

Red

Black White

Red

English - 10

Install_NE58H9970WS_AA_AC_DG68-00594A-05_EN+MES+CFR.indb 10 2017-08-11  6:28:42

Inhaltsverzeichnis

Sprachen:

Andere Samsung Reichweite Handbücher

Samsung

Samsung NE6 871 S Series Bedienungsanleitung

Samsung

Samsung NE59J342 Bedienungsanleitung

Samsung

Samsung NE58H9970WS Bedienungsanleitung

Samsung

Samsung FTQ307 Series Bedienungsanleitung

Samsung

Samsung NX58F5500SS Bedienungsanleitung

Samsung

Samsung NX58F5700WS Bedienungsanleitung

Samsung

Samsung NE59 432 Series Bedienungsanleitung

Samsung

Samsung NSE6D 87 Series Bedienungsanleitung

Samsung

Samsung NE59M4320 Serie Bedienungsanleitung

Samsung

Samsung NX58K7850SG/AA Bedienungsanleitung

Samsung

Samsung NX58M6630 Bedienungsanleitung

Samsung

Samsung NX58 Series Bedienungsanleitung

Samsung

Samsung NX58M6630S Series Bedienungsanleitung

Samsung

Samsung NX58 9420S Series Bedienungsanleitung

Samsung

Samsung FTQ353IWUX - 30in Electric Range Bedienungsanleitung

Samsung

Samsung DG68-00294A Bedienungsanleitung

Samsung

Samsung NE597N0PBSR Bauanleitung

Samsung

Samsung NE63 Series Bedienungsanleitung

Samsung

Samsung NX58 560 Series Bedienungsanleitung

Samsung

Samsung NX58J7750SS Bedienungsanleitung

Samsung

Samsung NX60 811 Series Bedienungsanleitung

Samsung

Samsung NSE6D 83 Series Bedienungsanleitung

Samsung

Samsung NX58K9850S series Bedienungsanleitung

Samsung

Samsung NX58K3310S series Bedienungsanleitung

Beliebte Reichweite Handbücher anderer Marken

Kenmore

Kenmore 790.45712 Bedienungsanleitung

Wolf

Wolf CHR CHSSR Bedienungsanleitung

Smeg

Smeg Built-in Microwave Oven Bedienungsanleitung

Zanussi

Zanussi ZCG054G Bedienungsanleitung

Whirlpool

Whirlpool 8575985-W Stücklistenhandbuch

Frigidaire

Frigidaire 316000635 Bedienungsanleitung

GE JCSS630 Bedienungsanleitung

Hotpoint

Hotpoint RB524R Installationsanleitung

Whirlpool

Whirlpool Roper FGP305KW3 Bedienungsanleitung

Amana

Amana ART6610 SERIES Bedienungsanleitung

Maytag

Maytag MERH770WB Bedienungsanleitung

Fulgor Milano

Fulgor Milano SOFIA Bedienungsanleitung

Premier

Premier EF-4358GH Bedienungsanleitung

Kenmore

Kenmore 790.9010 Series Bedienungsanleitung

KitchenAid

KitchenAid KESC300 Bedienungsanleitung

Frigidaire

Frigidaire FFEF3012LS Benutzerhandbuch

Diamond

Diamond G65/2F4T Bedienungsanleitung

LG LRE3091 Bedienungsanleitung