Samsung MWR-WE13 Bedienungsanleitung

Air conditioner

Installation manual

Wired remote controller MWR-WE13

• Thank you for purchasing this Samsung Product.

• Before operating this unit, please read this installation manual carefully and retain it for future

reference.

DB68-07634A-00

English

Contents

Safety Information 3

Installation 4

Wired Remote Controller Installation 4

Optional accessories

External Dimensions

Wired Remote Controller Installation

Tracking Your Indoor Unit from the Wired Remote Controller

Individual Control with YourWired Remote Controller

Group Control with YourWired Remote Controller

Controlling 2-Remote controller

Initializing YourWired Remote Controller Communication

Errors Displayed on Your Wired Remote Controller

Service Mode 17

Wired Remote Controller Installation/Service Mode 17

Additional Functions of YourWired Remote Controller

Installation/Service Mode

The example of Wired Remote Controller option setting method

Safety Information

English

This installation manual explains how to install a Wired Remote Controller connected to the indoor unit of your Samsung

system air conditioner. Please read this manual thoroughly before installing the product. (Please refer to appropriate

installation for any optional product installation.)

Safety Information

WARNING

Hazards or unsafe practices that may result in severe personal injury or death.

CAUTION

Hazards or unsafe practices that may result in minor personal injury or property damage.

WARNING

Contact a service centerfor installation.

• Potential risk of malfunction, water leak, electric shock

and fire.

Install the product with proper power supply.

• Potential risk of fire or product damage.

Consult the place of purchase ora contact centerto

disassemble or repair the product.

• Potential risk of malfunction, electric shock, or fire.

The electric work must be done by qualified person

according to national wiring regulations and installation

guide.

• If an unauthorized person performs the installation,

any resulting defects can cause malfunctions,

electrical shocks, or fire accidents.

Install the product on a hard and even place that can

support its weight.

• If the place cannot support its weight, the product may

fall down and it may cause product damage.

Do not move orreinstall the product on your discretion.

• Potential risk of electric shock or fire.

Check if the installation work is done correctly according

to the installation manual.

• Incorrect installation may cause electric shock or fire.

When you want to dispose your Wired Remote Controller,

ask the service center.

CAUTION

Do not install the product where there’s combustible gas.

• Potential risk of fire and explosion.

Ensure no water gets into the Wired Remote Controller.

• Potential risk of electric shock or fire.

Install the air conditioner away from direct exposure to

sunlight, in room temperature range of 0 °C(32 °F)~

39 °C(102 °F).

• Potential risk of electric shock or malfunction.

Do not handle the product with sharp objects.

• Potential risk of electric shock or product damage.

Do not install the product in areas exposed to oil orvapor.

• Potential risk of product damage or malfunction.

Do not put undue stress on the power cable.

• Potential risk of broken cable and fire.

Do not install the product in areas with frequent use of

acid or alkali spray.

• Potential risk of electric shock or product malfunction.

Do not connect power cable to a communication terminal.

• Potential risk of fire.

Be cautious not to interfere any other electrical devices if

the product is installed in a place such as hospital.

• Potential risk of product malfunction.

Ɵ˵ʪͱиʪϑϩϑʪϩϩʪΧʪθɇϩЇθʪϑϩʪʒϩͱߣߡʒʪ˝θʪʪϩ˵ʪƸkɇʀʀͱθʒ˝ϩͱƸkࢋƊߦߡߢߡࣗߦࡏߣߡߢߧࢋ

4English

Installation

Wired Remote Controller Installation

Optional accessories

Item Wired Remote

Controller Cable Tie Cable Clamp M4X16 Screw UserManual Installation

Manual U Terminal

Quantity 1235116

Shape

CAUTION

• The Wired Remote Controller should be installed by an installation expert.

• Check and confirm the power is off before installing your Wired Remote Controller.

• Install the Wired Remote Controller cables in accordance with the electrical wiring rules, and allow it to pass through

the inner area of the wall so that other people can’t reach it.

External Dimensions

120.0(4.72)

124.0(4.88)

63.8(2.51)

19.5(0.76)

[Unit : mm(inch)]

English 5

Installation

Wired Remote Controller Installation

1 Push the two hooks at the bottom of yourWired Remote Controller at the same time, and then pull up the

front cover to separate it from the rear cover.

࢘ťЇϑ˵ϩ˵ʪϩиͱ˵ͱͱϑɇϩϩ˵ʪϑɇʪϩʪࢋ

NOTE

• Insert a flat head screwdriver into the square groove in the upper area of

the hook to disassemble it easily.

2 Arrange the power cable and the communication cable so that they fit in the housing along the edges of the

rear cover.

15 cm(6 inch)

10 cm

(4 inch)

If you need more space for the

wiring work, you can take it off.

Wired Remote Controller Installation

English

Installation

3 Using more than two screws, firmly affix the rear cover of the remote controllerto the wall, and then connect

the power(V1, V2) and communication cables(F3, F4), making sure these cables have reasonable length,

to the terminal at the back of the cover.

10 mm (0.4 inch)

or more

10 mm

(0.4 inch)

or more

50 mm(2 inch)

or more

10 mm(0.4 inch)

or more

Screw

hole

Rear cover

Front cover

PCB terminal

Wire (not supplied)

࢘9ʪ˙ͱθʪ˙у˝ϩ˵ʪθʪɇθʀͱЭʪθࡡ

secure at least10 mm(0.4 inch)

space of upper side, left side,

right side, and 50 mm(2 inch)

space of bottom side.

࢘ǽͱЇЇϑϩ˙ϩϩ˵ʪϑʀθʪиϑ

into the screw holes.

࢘Uͱͱϩϩ˝˵ϩʪϩ˵ʪϑʀθʪиϑͱϩ˵ʪ

PCB terminal with excessive force.

Indoor unit

Wired

Remote

Controller

4 Reassemble your Wired Remote Controller.

NOTE

• Align the controllerwith the upper groove first, and insert it by turning it

downward as shown in the figure.

After assembly, check and confirm that no wires are stuck in the gap

between the rear and front cover.

CAUTION

• When installing a Wired Remote Controller by using a cable longer than 10 m(32.80 ft), you must install the

communication cable and the power cable separately. (Electrical interference can cause your Wired Remote Controller

to malfunction.)

• When installing yourWired Remote Controller on the wall, consider the size of the wire hole, and select a wire with a

proper thickness.

• Wire that is connectable to Wired Remote Controller PCB.

– If you install the Wired Remote Controller by reclaiming, install it according to U-terminal cable specification.

– If you install the Wired Remote Controller by using four pieces of PVC wire, remove the 30 cm(12 inch) of the sheath

of the cable and install it only with the four pieces of wires. (Recommended specification: AWG20)

English 7

Installation

• The following are the specs of the compression ring terminal connected to yourWired Remote Controller PCB.

Stud ØD

ŵɇ˝ʪͱ˙ťʪθϩϩʪʒǮθʪϑ Rated Size Stud Size Basic Size [mm (inch)]

AWG mm²

(inch²)

mm²

(inch²)

(inch) tØDG E F W L

22~16 0.25~1.65

(0.0003 ~ 0.0025) 1.5 (0.0023) 3 (0.1181) 0.7

(0.0275)

3.8

(0.1496)

10.0

(0.3937)

4.5

(0.1771)

6.5

(0.2559)

6.0

(0.2362)

21.2

(0.8346)

࢘đɇуЇʒϑϩɇʀʪ˙ͱθʀͱʪʀϩ˝ʀͱЇʀɇϩͱɇʒΧͱиʪθʀɇɵʪࡠߢߡߡ࣍ߤߣߩ˙ϩ࣎

• Screws on the PCB terminal must be tightened with less than 6N-cm tightening torque. If the tightening torque is

greater, it may damage the screw thread.

Tracking Your Indoor Unit from the Wired Remote Controller

Indicates tracking

in progress

Displays the total number of

units searched

1 Tracking of your Wired Remote Controllerwill automatically start when you turn on the power after installation.

2 If you want to perform tracking again after installation, then press the Delete and ESC buttons at the same time for

more than five seconds.

• The system will reset, and tracking will start again.

3 During tracking, the total number of currently searched indoor units and ventilator(ERV) will be displayed.

4 It may take about 5 minutes at initial installation orwhen you re-set the Master setting.

NOTE

• If you want to perform tracking again after installation, then press the Delete and ESC buttons at the same time

for more than five seconds.

• Only the masterWired Remote Controller can display the total number of indoor units and ventilator(ERV).

– Slave Wired Remote Controllers do not display the total number of units.

Wired Remote Controller Installation

English

Installation

Individual Control with YourWired Remote Controller

Individual control means that you are using one remote controller to control one indoor unit or ventilator(ERV).

When Connected to an Indoor Unit Only

COM1 (F1, F2)

COM2 (F3, F4) COM2 (F3, F4) COM2 (F3, F4)

COM1 (F1, F2)

Outdoor Unit

IndoorUnit IndoorUnit IndoorUnit

Wired Remote

Controller

Wired Remote

Controller

Wired Remote

Controller

When Connected to an ventilator(ERV) Only

COM1 (F1, F2) COM1 (F1, F2)

COM2 (F3, F4) COM2 (F3, F4) COM2 (F3, F4)

Ventilator(ERV) Ventilator(ERV) Ventilator(ERV)

Wired Remote

Controller

Wired Remote

Controller

Wired Remote

Controller

Masterventilator(ERV)

NOTE

• Regardless of the indoor group address (RMC address) orthe ventilator(ERV) group address, only the indoor unit

connected to COM2 is individually controlled.

• The power cable (V1, V2) is not connected between indoor units.

English 9

Installation

Group Control with YourWired Remote Controller

Group control means that you are using one Wired Remote Controller to control two or more indoor units and

ventilator(ERV) at the same time.

When Connected to an Indoor Unit Only

• Using One Wired Remote Controller to control three indoor Units

COM1 (F1, F2)

COM2 (F3, F4) COM2 (F3, F4)

COM1 (F1, F2) COM1 (F1, F2)

Outdoor Unit

Wired Remote Controller

IndoorUnit IndoorUnit IndoorUnit

• Using One Wired Remote Controller to control indoor units connected to different outdoor unit

COM1 (F1, F2)

COM2 (F3, F4)

COM1 (F1, F2)

Outdoor Unit

IndoorUnit

Wired Remote Controller

Outdoor Unit

IndoorUnit

NOTE

• Regardless of the indoor unit’s group address (RMC address), only the indoor units connected to COM2 are controlled

in group.

• The power cable (V1, V2) is not connected between indoor units.

• The power cable for your Wired Remote Controller (V1, V2) should be connected to only one indoor unit.

• Regardless of your outdoor units, you can control a maximum of16 indoor units as a group.

• Address of each outdoor units must be set differently when group control indoor units connected to the other outdoor unit.

Wired Remote Controller Installation

English

Installation

When Connected to an ventilator(ERV) Only

• Using One Wired Remote Controller to Control Three ventilator(ERV)

Master ventilator(ERV)

COM1 (F1, F2) COM1 (F1, F2) COM1 (F1, F2)

COM2 (F3, F4)COM2 (F3, F4)

Wired Remote Controller

Ventilator(ERV) Ventilator(ERV) Ventilator(ERV)

NOTE

• Regardless of the ventilator(ERV)'s group address (RMC address), only the ventilator(ERV) connected to COM2

controlled in group.

• The power cable (V1, V2) is not connected between ventilators(ERV).

• The power cable foryourWired Remote Controller (V1, V2) should be connected to only one ventilator(ERV).

Inhaltsverzeichnis

Andere Samsung Fernbedienung Handbücher

Samsung

Samsung Smart Remote BN68 Series Bedienungsanleitung

Samsung

Samsung SWPZ01-TX Bedienungsanleitung

Samsung

Samsung VG-TM2360E Bedienungsanleitung

Samsung

Samsung BN68-03092A-02 Bedienungsanleitung

Samsung

Samsung MWR-WW10N Bedienungsanleitung

Samsung

Samsung MWR-SH00 Bedienungsanleitung

Samsung

Samsung MWR-SH11UN Bedienungsanleitung

Samsung

Samsung MWR-SC00T Bedienungsanleitung

Samsung

Samsung MWR-WE10 Bedienungsanleitung

Samsung

Samsung MWR-WE10 Bedienungsanleitung

Samsung

Samsung SolarCell Remote Bedienungsanleitung

Samsung

Samsung RMC-QTD1 Bedienungsanleitung

Samsung

Samsung MWR-SH10N Bedienungsanleitung

Samsung

Samsung SolarCell Remote Bedienungsanleitung

Samsung

Samsung RMCSPM1AP1 Bedienungsanleitung

Samsung

Samsung MWR-WS00 Bedienungsanleitung

Samsung

Samsung MWR-TH00 Bedienungsanleitung

Samsung

Samsung MWR-WW10N Bedienungsanleitung

Samsung

Samsung MWR-WE10N Bedienungsanleitung

Samsung

Samsung SMART TV Leitfaden

Samsung

Samsung SolarCell Remote Bedienungsanleitung

Samsung

Samsung MR-BH01 Bedienungsanleitung

Samsung

Samsung MWR-WE10N Bedienungsanleitung

Samsung

Samsung MWR-WH00 Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung