Samsung WA5471 Series Handbuch

WASHING MACHINE

Technical Information

Code No. : DC68-03051A-01_EN

• Duetopossibilityofpersonalinjuryorpropertydamage,alwayscontactanauthorized

technicianforservicingorrepairofthisunit.

• RefertoServiceManualfordetailedinstallation,operating,testing,troubleshooting,and

disassemblyinstructions.

Models : WA5471*

WA5451*

AllsafetyinformationmustbefollowedasprovidedinServiceManual.

CAUTION

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

WA5471ABP_03051A-01(Technical information).indd 1 2011-05-30 �� 2:38:32

ALIGNMENT AND ADJUSTMENTS

GENERAL ERROR FUNCTION

Error Code

(Diagnostic Code

Error Image)

Description Corrective Action

1nd Thewaterlevelfailstodropbelowthe

ResetWaterLevelwithin30minutes.

Goto“WillNotDrain”Troubleshooting

Section.

2LO DoorfailstoUnlockAfter7attempts. Goto“WillNotUnlock”

TroubleshootingSection.

3nF

WhenthellingContinuesformore

than60minutesorthereisnochange

ofwaterlevelfor6minutes.

Goto“NoWaterFill”Troubleshooting

Section.

4FL Doorfailstolockafter7attempts. Goto“WillNotLock”Troubleshooting

Section.

5LE

AwaterlevellowerthantheReset

waterlevelisdetectedfor5seconds

duringtheWash/Rinsecycle.

Goto“NoWaterFill”Troubleshooting

Section.

6 1E

WaterLevelSensorTrouble.(When

theinputsignalfromthewaterlevel

sensorisoutofrange,theunitwill

sendoutbeepingsoundsandhalts

thecycle.)

Goto“NoWaterFill”

TroubleshootingSection

7 OE

Afaultisdetectedinthewaterlevel

sensor.Data(frequency)showsthe

waterlevelisatorabovetheoverow

waterlevel.(Whenthiscondition

isdetected,themachinewill

automaticallystartsdrainingwater

untilthewaterlevelfallsbelowthe

resetwaterlevel)

Firstchecktoseethatallofwater

valvesarenotstuck.Ifwatervalves

areOK,checkwaterlevel.

8dc Unbalanceorcabinetbumpis

detectedduringnalspin

Goto“WetClothes”Troubleshooting

Section.

9 E2

JammedKey.(Whenkeyinputsignals

arecomingoutformorethan30

seconds,itisregardedasajam.)

Checkallofkeys.IfAkeyissensed

tobepressed,allkeyswilldonot

respond.

10 ds Doorisdetectedasopenwhileitis

tryingtolockthedoor.

Goto“QuickTestMode”andthendo

DoorLock/UnlockTest

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

WA5471ABP_03051A-01(Technical information).indd 2 2011-05-30 �� 2:38:32

ALIGNMENT AND ADJUSTMENTS

Error Code

(Diagnostic Code

Error Image)

Description Corrective Action

11 TE1

Thisoccurswhenthewater

temperaturesensorfaultisdetected

continuouslyfor5seconds.

Goto“BoardInputTest”andcheck

WaterTemperature.Checkloose

orpinchedwires.ReplacePCBor

thermistor.

12 3E

MICOMisattemptingtodrivethemotor

butisnotgettinganyresponsesignals

fromthehallsensor.Visualcheckshows

motorisnotrunning.(Locked,Defective

HallSensororOverload)

Evaluatewireharnessforlooseor

unhookedconnections.Goto“Quick

TestMode”andtestMotor.

13 HE HeaterRelayFailure(NoHeaterRelay

CheckSignal) ReplacePCB

14 nF1 Thehot/coldwaterhoseconnectionis

notcorrect.

Pleaseconnectthehot/coldwater

hoseconnectioncorrectly.

15 SUd

Sudsisdetectedduringthewashing

session.(“SUdS”isnotanerror.When

itnisheswashing,EndandtheSUd

codewillblinkinturn.)

Guideausertoreduceamountof

detergentusage.

16 AE

CommunicationerrorbetweenSUB

PBAandMAINPBA

CheckMainPBA,SUBPBA&Wire-

harness.ReplacePCB

17 PE

(ClutchMotorError)

Thiserroroccurswhenthepositionof

theclutchisnotdetected.

-Ifthepositiondetectionsignalisnot

received15secondsaftertheclutch

motorstarts,thespindrumisshaken

leftandrightandthenthemotoris

restarted.

Ifthemotorpositionsignalisnot

receivedevenafter3reattempts,aPE

erroroccurs.

1.Checktheclutchmotor.

2.Checktheassemblystatusofthe

clutchmotor.

3.Checkthewireconnectorterminals.

PE1

(clutchhallsensor

error)

Afterthecompletionoftheclutch

positiondetection,andtheclutch

hallsignalisinvalid,thespindrum

isshakenleftandrightandthenthe

clutchhallsignalisevaluatedagain.

This,iftheclutchhallsignalisstill

invalid,theclutchpositionswitching

statusischeckedandthenthe

operationisrestarted.

(Ifthe15reattemptsfail,thiserror

occurs.)

1.Checktheclutchhallsensor.

2.Checkthewireconnectorterminals.

3.Checktheclutchswitchingstatus.

-Checkthecouplingassemblyand

disassemblystatus.

19 8E

IftheoutputfromtheMEMSsensor

isover4.5Vorunder0.5Vandit

continuesfor5seconds,thiserror

occurs.

1.ChecktheMEMSsensorandPBA.

2.Checkthewireconnectorterminals

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

WA5471ABP_03051A-01(Technical information).indd 3 2011-05-30 �� 2:38:32

ALIGNMENT AND ADJUSTMENTS

TEST MODE

Test Mode:

EachTestModefortheORCAisasfollowsinthe

comingpages.Thetestmodesindicatedbythe

redarrowsaremodesunabletogetanaccess

oncethewashingcyclehasstartedduetosafety

resons.

Quick Test Mode

Denition of Quick Test Mode:

- CheckoperationofallLED’s(VerifyfaultyLED).

- Checkmodelandsoftwareversion.

- Checkdierentoperatingmodes(e.g.watervalve,motor,door,drainpump,etc.).

How to Enter:

- Plugintheunit.

- Pressspinkey,soillevelkeyandPowerKeyatthesameTime.

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

WA5471ABP_03051A-01(Technical information).indd 4 2011-05-30 �� 2:38:33

ALIGNMENT AND ADJUSTMENTS

Quick Test Mode:

1. AllLED’slightupanditsendsoutBeepSoundwhenit

entersintotheQuickTestMode.(Including7-Segment)

2. DisplayssoftwareversionforasecandClearEEprom.

3. Whentheversionisdisplayed,turntheJog-Dialsothat

theversiondisappears.Pressthefollowingkeystotestthe

variouscomponents.

-TempKey:WaterValveTest

-Signal:DoorLock/UnlockTest

-SoilKey:WaterHeaterTest

-Spin:Drain/circulationpumptest

EEPROM Clear Check

Denition of EEPROM Clear Mode:

- EEPROMinitialization.

- Allcourse/optionsettingsaretoberesettodefault

valuesafterEEPROMinitialization.

- WhenServicearisesanditneedsPCBreplacement,

EEPROMshouldbereset.

How to Enter:

- Theunitneedstobeon.

- PressDelayStartKey,andPowerKeyatthesame

time.

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

WA5471ABP_03051A-01(Technical information).indd 5 2011-05-30 �� 2:38:33

ALIGNMENT AND ADJUSTMENTS

Continuous Run Mode

Denition of Continuous Run Mode:

- WillcontinuouslyrepeatthecurrentcycleuntiltheContinuousRunModeiscancelled.

How to Enter:

- PressDelayStart+SoilLevelKeytogetherfor7sec.

Continuous Run Mode:

1. Press

DelayStart+SoilLevel

Keyfor7secduringPowerOnState(NormalUserMode).

OnceinContinuousRunMode,Thesevensegmentswillnolongerdisplay“0000”andwillalternate

betweendisplayingthenumberofcyclesofthecompletedcourseandtheremainingtimeofthecourse.

3. TheContinuousRunModewillrepeatthepreviouscycleuntilcontinuousrunmodeiscancelled.

DuringContinuousRunMode,pressDelayStart+SoilLevelKeyfor7sectoreturntonormal

usermode.Thesevensegmentswillnolongerdisplaythenumberofcyclesandwilldisplaythe

maintenancetimeonly.

5. IfyouexitServiceModeafterenteringitfromContinuousMode,thewashingmachinereturns

toContinuousMode.

6. IfpowerislostinContinuousRunMode(thatis,whenthepowerplugisdisconnectedorthe

Powerkeyispressedturningthewashingmachineo),themodeisreleasedwhenthewashing

machineisturnedonagain.

Service Mode

Denition of Service Mode:

- ServiceModeenablesservicetechnicianstoverifytheoperationofthewashingmachineand

dotroubleshooting.

- ServiceModecanbeenteredduringallwashingcyclewithoutinterruptingthecycleexcept

someoftestmodes.

- VarioustestscanbedonewithServiceMode.So,troubleshootingcanbedonebasedonthe

resultingdiagnosticcodes.

How to Enter:

- ToentertheServiceMode,presstheSignalandExtraRinseKeysfor3secondsoruntiltheunit

sendsoutbeepingsounds.

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

WA5471ABP_03051A-01(Technical information).indd 6 2011-05-30 �� 2:38:34

ALIGNMENT AND ADJUSTMENTS

Service Mode

Service Mode:

1.ThewashermustbeontogointotheServiceMode.

2.Themotorspeedwillbedisplayedwhenstarted(Itdisplays0whenthemotordoesnotspin).

3.Thepresentstateofthemachinewillnotbechanged.

(i.e.,thecurrentcycleinprogresswillnotbeinterruptedandonlythedisplaywillchange)

4. ToexitServiceMode,pressSignalandExtraRinseKeysfor3secondagain,orPowerKey.Ifnokey

isoperatedduringServiceModefor5minutes,themachinewillreturntonormalusermode.

Quick Spin Test Mode

Denition of Quick Spin Test Mode:

- QuickSpinTestModeistodoSpinCheck.(HighRPM)

How to Enter:

- DuringServiceMode,presstheDelayStartandTemp.Keysfor3secondstoenterQuickSpin

TestMode.

- Cannotenteroncethewashingcyclehasstarted.

Quick Spin Test Mode:

AsitentersintotheQuickSpinTestMode,itstartsspinningandreachestoitsmaximumRPM.

OncetheSpinspeedreachesthemaximumRPM,thespeeddropsimmediately.

ToholdQuickSpinTestMode(enteringHoldSpeedMode),presstheStart/Pausebutton.Ifthe

Start/PausebuttonispressedduringQuickSpinTestMode,itwillstopacceleratingandholdits

spinningspeedfor10minutesbeforegoingbacktoQuickSpinTestMode.

Also,tocanceltheholdandallowQuickSpinTestModetocontinue,presstheDelayStartand

TempKeystogetherfor3seconds.

IfyouholddowntheDelayStartandTemp.keysforthree(3)secondswhenthewashingmachine

isnotinHoldSpeedMode,QuickSpinModeisexitedandServiceModeisrestored.

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

WA5471ABP_03051A-01(Technical information).indd 7 2011-05-30 �� 2:38:34

ALIGNMENT AND ADJUSTMENTS

Cycle Count Check Mode

Denition of Cycle Count Check Mode:

- CycleCountCheckModeistotallyupthenumberofwashings.

How to Enter:

- ToentertheCycleCountCheckMode,presstheSignalKeyduringServiceMode.

Cycle Count Check Mode:

1. ActivatetheServiceModeinadvance.

2.WhentheSignalkeyispressed,thetotalnumberofwashingswilllightupandasignalLEDwill

glow.

3.Themaximumnumberofcycleswillbe1999.

Thecounterwillrolloverto0andstartcountingagainafter1999.

4.Thecountingwillbecarriedoutattheendofthenormalcycle.

(FornormalandContinuousRuncycles,thecountiscarriedoutattheendofthecycles.

5. ToexittheCycleCountCheckMode,pressthe“Signal”keyagain.

S/W Version Check Mode

Denition of S/W Version Check Mode:

- S/WVersionCheckModeistobringupS/WVersioninformation.

How to Enter:

- ToentertheS/WVersionCheckMode,presstheSoilLevelKeyduringServiceMode.

S/W Version Check Mode:

1. ActivatetheServiceModeinadvance.

2. PresstheSoilLevelKeytobringupitssoftwareVersion

EX)GeneratedE49atVersion49(dEisMicomcode,49isit’ssoftwareversion)

3. ToexittheS/WVersionCheckMode,presstheSoilLevelS/Wonceagain.

Then,itreturnstotheServiceModewithmotorRPMilluminating.

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

WA5471ABP_03051A-01(Technical information).indd 8 2011-05-30 �� 2:38:34

ALIGNMENT AND ADJUSTMENTS

Fast Time Down Test Mode

Denition of Fast Time Down Test Mode:

- FastTimeDownTestModeistoforwardtheprogramtothenextcyclestage.

How to Enter:

- ToentertheFastTimeDownTestMode,presstheTempkeyduringServiceMode.

Fast Time Down Test Mode:

1. ActivatetheServiceModeinadvance.

2. Toforwardtheprogramtothenextcyclestage,presstheTempkey.

Each stage is located at key points of a complete cycle as follows:

- EndofEachFill(BeginningofWashorRinseTumbleSession)

Caution:CheckifthecurrentwaterlevelishigherthantheResetwaterlevelandthenperform

theFasttimedowntest.

- BeginningofDrainSession

- BeginningofSpinSession(Here,itchecksthewaterlevel.So,ifitisovertheresetlevel,itcarries

outdrainingbeforethespinning.)

- BeginningofFillSession

- BeginningofBleachFill

- BeginningofFabricSoftenerFill

- Every3minutesduringWashandRinseTumbleSession

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

WA5471ABP_03051A-01(Technical information).indd 9 2011-05-30 �� 2:38:35

ALIGNMENT AND ADJUSTMENTS

Board Input Test Mode

Denition of Board Input Test Mode:

- BoardInputTestModeistodisplaysaspeciedinputafterakeypress.

How to Enter:

- ToentertheBoardInputTestMode,presstheExtraRinsekeyduringServiceMode.

Board Input Test Mode:

1. ActivatetheServiceModerst.

2. PressthekeytostartBoardInputTest.

3.TurntheJog-Dialsothatthenormalcourseisturnedon,andTheWaterTemperaturewillbe

displayedinCelsius.

4.TurntheJog-DialsothattheHeavydutycycleisturnedon,TheWaterTemperaturewillbe

displayedinFahrenheit.

5.TurntheJog-DialsothatthePermPresscycleisturnedon,Thedoorstatuswillbedisplayed(OP

ifopen,CLifclosed).

6. TurntheJog-DialsothattheRinse+SpinorQuickWashisturnedon,TheDoorLockSwitch

statuswillbedisplayed(ULifunlocked,LOiflocked).

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

WA5471ABP_03051A-01(Technical information).indd 10 2011-05-30 �� 2:38:35

Andere Handbücher für WA5471 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Samsung Waschmaschine Handbücher

Samsung

Samsung WW9 K6 Series Bedienungsanleitung

Samsung

Samsung WA95F3 Bedienungsanleitung

Samsung

Samsung WF8654QM Bedienungsanleitung

Samsung

Samsung WD17T6300 Series Bedienungsanleitung

Samsung

Samsung SW85ASP Bedienungsanleitung

Samsung

Samsung WA14R6380B Series Bedienungsanleitung

Samsung

Samsung WAE28162GB Bedienungsanleitung

Samsung

Samsung WA12B9 Bedienungsanleitung

Samsung

Samsung C1035A Bedienungsanleitung

Samsung

Samsung WF8508NMW9 Bedienungsanleitung

Samsung

Samsung WA90GP Bedienungsanleitung

Samsung

Samsung WA5471AB Series Bedienungsanleitung

Samsung

Samsung WA75H4000H Bedienungsanleitung

Samsung

Samsung WF14F5K3AVW Bedienungsanleitung

Samsung

Samsung WF8702RSS Stücklistenhandbuch

Samsung

Samsung WF206BNW/XAA Bedienungsanleitung

Samsung

Samsung WA8535B1 Bedienungsanleitung

Samsung

Samsung WA90H7000G series Bedienungsanleitung

Samsung

Samsung WF231 Series Bedienungsanleitung

Samsung

Samsung WF361BVBEWR Installationsanleitung

Samsung

Samsung FlexWash WR24M9940K Series Bedienungsanleitung

Samsung

Samsung WF602W2BD Series Bedienungsanleitung

Samsung

Samsung WA12H2 Bedienungsanleitung

Samsung

Samsung WF316B /XAA Series Bedienungsanleitung

Beliebte Waschmaschine Handbücher anderer Marken

Tricity Bendix

Tricity Bendix AW 1000 W Produkthandbuch

Panasonic

Panasonic NA-F60L5WRB Bedienungsanleitung

GE WSLP1500 Handbuch

Electrolux

Electrolux EWF1284EDW Bedienungsanleitung

Bosch

Bosch WAN2829BSN Bedienungsanleitung

LG TV2516DV3B Bedienungsanleitung

LG TH2517DSAV Bedienungsanleitung

VESTEL

VESTEL CMH-XL 7510 TE Bedienungsanleitung

AEG

AEG 74335 Bedienungsanleitung

Johnson

Johnson JWF721A Bedienungsanleitung

Beko

Beko WTE7604XLW0 Bedienungsanleitung

Danby

Danby DTT100A1WDB Montageanleitung

Amica

Amica WA 14 Ex Bedienungsanleitung

Daewoo

Daewoo DWD-F1222 Bedienungsanleitung

Bosch

Bosch WAS28461AU Bedienungsanleitung

Miele

Miele PW 6080 Vario Bedienungsanleitung

Finlux

Finlux FLX108CF220 Bedienungsanleitung

Whirlpool

Whirlpool 3LBR5132AN0 Bedienungsanleitung