Sanctuary SA-DIA4 Bedienungsanleitung
IMPORTANT:
Please read this information and follow all safety rules carefully before
operating your security safe. Failure to do so will void your warranty.
033023
SECURITY SAFE INSTRUCTION MANUAL
FOR SA-DIA1, SA-DIA2, SA-DIA3 AND SA-DIA4
TABLE OF CONTENTS
www.saproducts.com 1
IMPORTANT INFORMATION ............................................................................................... 2
1. REGISTRATION ................................................................................................................ 3
2. UNDERSTANDING YOUR SAFE ...................................................................................... 4
3. INITIAL ENTRY .................................................................................................................. 5
4. ELECTRONIC LOCK SECURITY CODE SETUP....................................................................... 6
5. OPENING YOUR SAFE WITH PROGRAMMED SECURITY CODE.......................................... 8
6. LOCKED OUT OF THE SAFE............................................................................................... 8
7. INTERNAL LIGHTING .........................................................................................................9
8. LOW BATTERY WARNING................................................................................................. 9
9. LOCKOUT MODE / TAMPER PROTECTION........................................................................ 9
10. SILENT ENTRY MODE .................................................................................................... 10
11. PROPER PLACEMENT AND MOVING OF SAFE ..............................................................10
12. KEEPING YOUR SAFE DRY.............................................................................................10
13. SECURING YOUR SAFE .............................................................................................. 11
14. LOADING YOUR SAFE .................................................................................................12
15. HINGES AND INTERNAL MECHANISMS........................................................................ 12
LIFETIME WARRANTY........................................................................................................ 13
DISCLAIMER - READ BEFORE SAFE SETUP
WEAPON STORAGE
SAFETY
Thank you for choosing a Sanctuary safe to protect your valuables. We are
commied to securing, organizing and protecng your most important documents,
valuables and keepsakes.
If you experience problems or challenges with your safe, please contact us.
Many issues can be quickly resolved without the product being returned.
Be sure to keep override keys stored in a secure place away from unauthorized users.
If you choose to ulize this safe to store a firearm alwaysfollow proper firearm
storage and local laws.
SA Consumer Products strongly recommends that you do not store loaded firearms.
Always follow the firearm safety rules set out by the firearm’s manufacturer.
A Sanctuary safe or any other firearm storage device cannot take the place
of other safety procedures including advising children of the dangers of firearms.
SA Consumer Products and its distributors of the Sanctuary safes do not
recommend, suggest, advise, promote, or otherwise condone the ownership
or use of firearms. We believe the decision to own or use a firearm is a serious
decision that should only be made by an adult who has carefully considered
the risks and benefits of such a decision.
PLEASE READ THIS INFORMATION CAREFULLY BEFORE OPERATING YOUR
SANCTUARY SAFE.
DO NOT LOCK THIS MANUAL OR THE OVERRIDE KEYS IN YOUR SAFE.
2
3
www.saproducts.com
REGISTRATION INFORMATION
PURCHASE DATE:
PURCHASE PRICE (BEFORE TAX):
MODEL NUMBER:
SERIAL NUMBER:
KEY NUMBER (IF APPLICABLE):
1. REGISTRATION
RETAILER NAME:
Please ensure you register your safe by vising our website. Locate the
“contact” buon on the top header on the home page. Select registraon
from the drop down menu.
By registering your Sanctuary safe we will be able to expedite and address
any problems or challenges you may have which would otherwise require a
notary leer and proof of payment.
The informaon you record onto this page will be required in the event you
cannot access the contents of your Sanctuary safe. Please fill out all the required
informaon below and retain for your records and safe keeping.
PLEASE HAVE THIS INFORMATION READY PRIOR TO CALLING FOR TECHNICAL
ASSISTANCE AT:
2. UNDERSTANDING YOUR SAFE
Handle
4
Electronic
Lock Face
Override
Key Entry
(underneath
keypad)
Active
Locking
Plates
Key
Hooks
Adjustable Shelves
(SA-DIA1 only has one shelf
SA-DIA4 has 3 shelves)
Door Organizer
Storage Pocket
Bolt
Down Holes
Dead
Locking Plates
Interior Light
Reset
Button
Lighting
Activation Button
3. INITIAL ENTRY
5
1. Locate the override keys
inside the plasc bag
hanging on the front of
the safe.
4.
2.
3.
Locate the override key entry
on the door of the safe.
Insert the key and turn
clockwise from the 12 to
3 o'clock posion.
5.
Remove the lock face from
the box located inside the
safe.
BACK OF LOCK FACE
Locate the 1x9V baery.
Install into the baery
compartment on the back
of the lock face in the
proper orientaon. The
keypad will beep when
baeries are successfully
installed.
Turn the handle
counter-clockwise to
unlock the safe door. Open
the Ssafe door, then turn
the handle back to it's
starng posion so the
locking plates are extend-
ed. Remove the override
key and set aside.
Step 4Step 5
WARNING: The baeries must be inserted with the correct polarity. Exhausted baeries
must be removed from the product and discarded safely. Do not mix old and new
baeries. Do not mix alkaline or standard (carbon – zinc) baeries. Do not use recharge-
able (nickel – cadmium) baeries.
6
6.
3. INITIAL ENTRY (Continued)
Plug the electronic lock cable
into the back of the lock face.
The connector on the cable
will only fit into the
connector in the lock face in
one way.
Finally, we will install the
keypad onto the safe. First,
align the lock face to the
backer plate and slide the top
of the lock face up into the
two locking pins. Next, lightly
push up on the release tab
located on the boom of the
backer plate, allowing you to
push the lock face and secure
to the backer plate.
7.
Step 7 Step 6
4. ELECTRONIC LOCK SECURITY CODE SETUP
1.
Important: Your safe comes programmed with a factory code of [ 1 5 9 # ].
It is necessary to re-program your safe with a new security code you have personally
selected to provide maximum household security. Be careful, in choosing your new
security code, you’ll want to be sure that you can operate the unit quickly without
making an error.
To begin programming, open
door and extend locking plates
to ensure access to the safe.
On the inside of the safe door,
locate the red plasc cap.
Unscrew and remove the cap,
giving you access to the reset
buon. Press the reset buon.
You will hear 2 beeps and the
keypad will illuminate indicang
that you are now in
programming mode.
Reset buon
located
under plasc
cap
7
4. ELECTRONIC LOCK SECURITY CODE SETUP (Continued)
Enter your new 3 to 8 digit
security code followed by the
[ * ] symbol.
2.
x2 x2
SUCCESS!
GREEN
If programming is is successful: Keypad
will beep 2 mes and green LED will flash
2 mes.
If your code was not accepted: the
keypad will beep three mes and
the yellow LED will flash 3 mes.
Press the reset buon and start again.
Inacvity Timeout: If this programming sequence is not completed within 10
seconds the red LED will flash 3 mes and the keypad will shut down.
Return to step 1 to restart this process.
NEW 3-8 DIGIT SECURITY CODE
While the safe door is sll open,
confirm your newly entered
security code by entering the 3-8
digit code followed by the (#)
symbol.
If successful you will hear two
beeps and you will be able to
retract the bolts.
If unsuccessful, press the reset
buon and start again.
3.
Step 3
CONFIRM SECURITY CODE
8
6. LOCKED OUT OF YOUR SAFE
In the event you are locked out of your safe, use your override keys to gain access and
follow the steps in Secon 4: Electronic Lock Security Code Setup Instrucons.
If you have lost your override keys, or are sll having difficules, contact customer
service at the number below. Proof of purchase is required to obtain keys.
4264
5. OPENING SAFE WITH PROGRAMMED SECURITY CODE
With keys in hand, close and lock the door.
Enter your security code followed
by the (#) buon.
If the security code is accepted,
the yellow LED will flash 2 mes
followed by the green LED illuminang.
You now have access to your safe.
If the security code is rejected,
the yellow LED will flash 3 mes
and beep 3 mes.
*Now that your security code is successfully programmed, store your override
keys in a secure secondary locaon. If you are not able to open your safe with your new
programmed code, repeat secon 4 to program a new security code.
9. LOCKOUT MODE / TAMPER PROTECTION
8. LOW BATTERY WARNING
Red & Green = Low Baery
This safe is equipped to alert you of Low
Baery Mode. This Low Baery Warning is
iniated immediately aer a successful code
entry. The keypad will illuminate both the red
and green LED lights for 3 seconds. It is highly
advised to immediately replace the safe's
baeries to avoid being locked out of your safe.
9
7. INTERNAL LIGHTING
When the safe door is opened,
internal lighng acvates for 30
seconds.
If you need to acvate your light
longer, you can press the green light
acvaon buon on the inner door
panel. This will acvate the internal
lighng for an addional 30 seconds
each me it is pressed.
Internal Light
Light Acvaon
Buon
1. Three consecuve rejected security code entries puts
the safe in “Basic Lockout” mode. The keypad is
deacvated for 30 seconds.
2. Six consecuve rejected security code entries results
in “Severe Lockout” mode. The keypad is deacvated
for 5 minutes.
Note: During lockout mode, the yellow LED will light up once
every 10 seconds. When lockout mode has ended, the
green LED will flash 1 me and you will hear 1 beep to
signify the lockout mode has ended. You will now have
access to your keypad.
3. Aer the safe enters basic or severe lockout mode, the tamper indicator will trigger
to warn you that someone has unsuccessfully aempted to gain access to your safe.
This tamper indicator will signal immediately aer the next successful code is entered.
The yellow LED will flash 3 mes and in addion to a 3 second long beep.
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Sanctuary Sicher Handbücher
Sanctuary
Sanctuary SA-PV2M Bedienungsanleitung
Sanctuary
Sanctuary PLATINUM SA-PLAT1 Bedienungsanleitung
Sanctuary
Sanctuary SA-PV1M-BIO Bedienungsanleitung
Sanctuary
Sanctuary Platinum SA-PLAT1-BIO Bedienungsanleitung
Sanctuary
Sanctuary SA-PS1D Bedienungsanleitung
Sanctuary
Sanctuary DIAMOND SA-DIA1-COM Bedienungsanleitung
Sanctuary
Sanctuary Diamond SA-DIA1 Bedienungsanleitung
Sanctuary
Sanctuary BIOMETRIC SA-DIA1-BIO Bedienungsanleitung
Sanctuary
Sanctuary SA-PV2M-BIO Bedienungsanleitung
Beliebte Sicher Handbücher anderer Marken
Honeywell
Honeywell 2077D - 1.21 Cubic Foot Anti-Theft Safe Bedienungsanleitung
Hornady
Hornady SnapSafe Trunk Safe II Bedienungsanleitung
SPORTS AFIELD
SPORTS AFIELD SA-HD5-BIO Bedienungsanleitung
Honeywell
Honeywell 5912 Bedienungsanleitung
Phoenix
Phoenix FS1280F Bedienungsanleitung
Phoenix
Phoenix SS0992K Produktinformationsblatt
Technomax
Technomax Trony Series Handbuch
SPORTS AFIELD
SPORTS AFIELD INSTINCT BIOMETRIC Series Bedienungsanleitung
RICHTER CZECH
RICHTER CZECH LA Bedienungsanleitung
Olymp
Olymp GOsafe 110 Bedienungsanleitung
Phoenix
Phoenix SS0100E Produktinformationsblatt
Clarke
Clarke Strong-Arm CS1000K Bedienungsanleitung