S&C TripSaver II Bedienungsanleitung

July 21, 2014© S&C Electric Company Instruction Sheet 461-506

S&C TripSaver® II Controller

TripSaver II Controller Module User Guide

Table of Contents

Section Page Section Page

Regulatory Information for FCC and IC ..........2

Hardware

Contents of Controller Module ....................3

Software

Download Software.............................4

Install Software ................................4

Launch Software...............................4

Connect to a TripSaver II Controller Module ......5

2S&C Instruction Sheet 461-506

Regulatory Information for FCC and IC

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference

This device complies with Industry Canada licence-exempt RSS standard(s). Opera-

tion is subject to the following two conditions: (1) this device may not cause interference,

and (2) this device must accept any interference, including interference that may cause

undesired operation of the device.

Cet appareil est conforme aux normes Industry Canada exemptes de licence RSS

standard(s). Son fonctionnement est soumis aux deux conditions suivantes : (1) cet

appareil ne doit pas provoquer d'interférences et (2) cet appareil doit accepter toute

interférence, y compris les interférences susceptibles de provoquer un fonctionnement

indésirable.

IMPORTANT! Changes or modications not expressly approved by S & C Electric Company

could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

— Consult the dealer or an experienced radio/TV technician for help.

CAN ICES-3 (B)/NMB-3(B)

S&C Instruction Sheet 461-506 3

Contents of

TripSaverII

Controller Module

AC Adapter Power Outlet Plug Adapters

USB Dongle Contoller Module

This Manual

Hardware

4S&C Instruction Sheet 461-506

Software

Download Software IntelliLink® TS-II controller module Setup Software is available for download only to

customers who have purchased the Controller module. For each controller module

purchased, the user is entitled to install and use S&C IntelliLink TS-II Controller module

Setup Software on no more than two computers at a time. The latest software release is

posted on the S&C Automation Customer Support Portal at www.sandc.com/support/

automation-customer-support-portal.asp. You will need a username and password to

log into the portal. If you are a new S&C customer, complete the form in the lower section

of the webpage and a new username and password will be sent to you. If you already have

a password, click the LOG-IN TO SECURE SITE button. Enter username and password

to log into the portal. Download the installer ILTS Setup-1.165.15712.0 from the portal.

Install Software Double-click the downloaded installer le and follow the on-screen instructions. The

installer will automatically install Microsoft .NET framework onto your computer if the

required .NET version is missing. You will need administrative privileges to nish the

installation.

Launch Software Click the green ILTS icon on your desktop or in the start menu to launch IntelliLink TS-II

Controller Module Setup Software. A warning screen will be displayed right after the

software is launched. Read the message carefully and understand the warning.

Proceed by clicking the green “I have read and understand the above warning” button.

Once you launch the software, you can configure and save settings under the Standalone

(Offline) mode.

S&C Instruction Sheet 461-506 5

Connect to a TripSaver II Controller Module

To connect to a TripSaver II Controller module to apply your new settings, follow the

steps below.

Step 1

Install USB Transceiver

A USB Transceiver must be installed on

your computer to communicate with a

TripSaver II Controller Module. Insert the

USB Transceiver into any USB port on your

computer. The installation process should

be automatic. Note: You do not need the

USB transceiver to be installed to install

the software and to run the software in

Standalone (Ofine) mode.

Step 2

Assemble Power Supply and Power Up TripSaver II Controller Module

A TripSaver II Controller Module must be powered by the power module to enable

its communication capability. Complete the following steps before attempting to

communicate with your TripSaver II Controller Module.

(a) Insert the connector from the power

module onto the pins in the TripSaverII

Controller Module as shown in the

picture

(b) Install the proper power outlet plug

adapter onto the AC adapter.

6S&C Instruction Sheet 461-506

Connect to a TripSaver II Controller Module

(d) To verify that your TripSaver II

Controller Module is powered up,

place a magnet next to the controller

module as shown in picture and

observe the LCD screen. If the LCD

screen begins to scroll, it indicates

that the unit has been successfully

poweredup.

Your setup, at the end of Step 2, should

look like the picture on the right.

S&C Instruction Sheet 461-506 7

Connect to a TripSaver II Controller Module

Step 3

Obtain Transceiver ID

A Transceiver ID unique to each TripSaver II Controller Module is needed to establish

communications between your computer and the device. The ID consists of a 32-digit

character string in the format of

“0019C900.00020000. _ _ _ _ _ _ _ _ . _ _ _ _ _ _ _ _”.

You must enter the ID in order to communicate with each TripSaver II Controller

Module.

The Transceiver ID is also labelled on the top of the controller module side attached to

each TripSaver II Controller Module when it leaves S&C Electric Company.

Printed in U.S.A.

8S&C Instruction Sheet 461-506

Connect to a TripSaver II Controller Module

Step 4

Connect to Device

To connect to a TripSaver II Controller Module, select Connection > Connect to

Device from the main menu or click the Connect to Device icon in the quick access

toolbar. Make sure that the USB transceiver is already plugged into your computer.

Next, a Transceiver ID Request dialog

box will appear. Enter the Transceiver

ID of the TripSaver II Controller Module

you want to connect to, and click “OK” to

connect. The first 16 digits of the ID are

pre-typed. You only need to enter the last

16 digits.

Enter last 16 digits here

During the connection process, a status

bar will be displayed. Wait about ten sec-

onds for the connection process to finish,

or click “Cancel” to cancel the connection

process.

You will be able to see the Status Screen

after your TripSaver II Controller Module

is successfully connected. Now, you can

view existing settings, status information,

and event logs of the TripSaver II Controller

Module, or apply new settings to the device.

Andere Handbücher für TripSaver II

Inhaltsverzeichnis

Andere S&C Controller Handbücher

S&C

S&C BankGuard PLUS Bedienungsanleitung

S&C

S&C IntelliCap 2000 Bedienungsanleitung

S&C

S&C 6802 Benutzerhandbuch

S&C

S&C 6800 Series Stücklistenhandbuch

S&C

S&C BankGuard PLUS Handbuch

S&C

S&C BankGuard PLUS Leitfaden

S&C

S&C IntelliCap Bedienungsanleitung

S&C

S&C Vista SD Betriebsanleitung

S&C

S&C IntelliCap Plus Bedienungsanleitung

S&C

S&C Micro-AT Bedienungsanleitung

S&C

S&C GridMaster Bedienungsanleitung

S&C

S&C 6800 Series Bedienungsanleitung

S&C

S&C Micro-AT Bedienungsanleitung

S&C

S&C 5800 Series Betriebsanleitung

S&C

S&C Vista Betriebsanleitung

S&C

S&C IntelliCap Bedienungsanleitung

S&C

S&C BankGuard PLUS Bedienungsanleitung

S&C

S&C Vista SD Betriebsanleitung

S&C

S&C Micro-AT Bedienungsanleitung

S&C

S&C 6800 Series Bedienungsanleitung

S&C

S&C PMH Montageanleitung

S&C

S&C Micro-AT Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

S&C

S&C IntelliCap Plus Betriebsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

Regin

Regin CORRIGO L10 Bedienungsanleitung