S&C TripSaver II Bedienungsanleitung

July 13, 2020

TripSaver®II Cutout-Mounted Recloser

Outdoor Distribution (15 kV and 25 kV)

For Overhead Distribution Systems

Protection Setup Using

Service Center Conguration Kit

Table of Contents

Section Page Section Page

Introduction

Qualified Persons . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Read this Instruction Sheet . . . . . . . . . . . . . . . . . . . 2

Retain this Instruction Sheet. . . . . . . . . . . . . . . . . . . 2

Proper Application . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

End User License Agreement. . . . . . . . . . . . . . . . . . 3

Safety Information

Understanding Safety-Alert Messages. . . . . . . . . . . 4

Following Safety Instructions . . . . . . . . . . . . . . . . . . 4

Replacement Instructions and Labels . . . . . . . . . . . 4

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . 5

Shipping and Handling

Packing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installing TripSaver® II Service

CenterConfiguration Software Version 1.8

Computer Requirements . . . . . . . . . . . . . . . . . . . . . 8

Downloading Software . . . . . . . . . . . . . . . . . . . . . . . 8

Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . 9

Installing the USB Transceiver and

Power Supply

Installing the USB Transceiver . . . . . . . . . . . . . . . . .13

Assembling the Power Supply and

Powering Up the TripSaver II Recloser . . . . . . . .13

Transceiver ID

Obtaining the Transceiver ID . . . . . . . . . . . . . . . . . .15

Using TripSaver II Service Center Configuration

Software Version 1.8

Launching the Software . . . . . . . . . . . . . . . . . . . . . .17

Reading and Understanding the

Warning Message . . . . . . . . . . . . . . . . . . . . . . . .17

Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Menu Bar Functions . . . . . . . . . . . . . . . . . . . . . . . . 23

Additional Information Bar . . . . . . . . . . . . . . . . . . . 39

Entering Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

TCC Settings Screen . . . . . . . . . . . . . . . . . . . . . . . 43

NR Curve Settings Screen . . . . . . . . . . . . . . . . . . . 59

Sectionalizing Settings Screen. . . . . . . . . . . . . . . . 62

LCD Screen Settings Screen . . . . . . . . . . . . . . . . . 64

Status Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Event Logs Screen . . . . . . . . . . . . . . . . . . . . . . . . . 76

Functional Test Screen . . . . . . . . . . . . . . . . . . . . . . .81

Local Manual Open Settings . . . . . . . . . . . . . . . . . 86

Communication Settings Screen . . . . . . . . . . . . . . 89

R-NR Functions Screen . . . . . . . . . . . . . . . . . . . . . 92

Gateway Drop Open Screen. . . . . . . . . . . . . . . . . . 93

DNP Remote Drop Open Screen . . . . . . . . . . . . . . 95

Appendix A

List of Available Curves . . . . . . . . . . . . . . . . . . . . . 97

Appendix B

Available Screens for “Screens When

Dropped-Open” Selection . . . . . . . . . . . . . . . . . 99

Appendix C

Available Screens to Be Added to the “Display”

Screen Sequence. . . . . . . . . . . . . . . . . . . . . . . .101

Appendix D

Understanding the Active TCC Curve When the

TripSaver II Recloser is in R-NR Mode . . . . . . .104

Appendix E

Regulatory Information . . . . . . . . . . . . . . . . . . . . . .105

2S&C Instruction Sheet 461-504

Qualified Persons WARNING

The equipment covered by this publication must be installed, operated, and

maintained by qualified persons who are knowledgeable in the installation,

operation, and maintenance of primary distribution fusing equipment along with

associated hazards. A qualified person is one who is trained and competent in:

• The skills and techniques necessary to distinguish exposed live parts from nonlive

parts of electrical equipment

• The skills and techniques necessary to determine the proper approach distances

corresponding to the voltages to which the qualified person will be exposed

• The proper use of the special precautionary techniques, personal protective

equipment, insulating and shielding materials, and insulated tools for working on

or near exposed energized parts of electrical equipment

These instructions are intended only for such qualified persons. They are not

intended to be a substitute for adequate training and experience in safety

procedures for this type of equipment.

Read this

Instruction Sheet NOTICE

Thoroughly and carefully read this instruction sheet and all materials included

in the product’s instruction handbook before installing or operating your

TripSaver II Cutout-Mounted Recloser. Familiarize yourself with the Safety Information

and Safety Precautions on pages 4 and 5. The latest version of this publication is

available online in PDF format at sandc.com/en/support/product-literature/.

Retain this

Instruction Sheet

This instruction sheet is a permanent part of your TripSaver II Cutout-Mounted Recloser.

Designate a location where you can easily retrieve and refer to this publication.

Proper Application WARNING

The equipment in this publication must be selected for a specific application. The

application must be within the ratings furnished for the selected equipment, and can

be found in S&C Specification Bulletin 461-33.

Introduction

S&C Instruction Sheet 461-504 3

Introduction

Warranty The warranty and/or obligations described in S&C’s standard conditions of sale, as set

forth in Price Sheet 150, plus any special warranty provisions, as set forth in the applicable

product-line specication bulletin, are exclusive. The remedies provided in the former

for breach of these warranties shall constitute the immediate purchaser’s or end user’s

exclusive remedy and a fulllment of all the seller’s liability. In no event shall the seller’s

liability to the immediate purchaser or end user exceed the price of the specic product

that gives rise to the immediate purchaser’s or end user’s claim. All other warranties,

whether express or implied or arising by operation of law, course of dealing, usage of

trade or otherwise, are excluded. The only warranties are those stated in Price Sheet 150,

and THERE ARE NO EXPRESS OR IMPLIED WARRANTIES OF MERCHANTABILITY

OR FITNESS FOR A PARTICULAR PURPOSE. ANY EXPRESS WARRANTY OR OTHER

OBLIGATION PROVIDED IN PRICE SHEET 150 IS GRANTED ONLY TO THE IMMEDIATE

PURCHASER AND END USER, AS DEFINED THEREIN. OTHER THAN AN END USER,

NO REMOTE PURCHASER MAY RELY ON ANY AFFIRMATION OF FACT OR PROMISE

THAT RELATES TO THE GOODS DESCRIBED HEREIN, ANY DESCRIPTION THAT

RELATES TO THE GOODS, OR ANY REMEDIAL PROMISE INCLUDED IN PRICE

SHEET 150.

End User License

Agreement

The end user is granted a nontransferable, non-sublicensable, nonexclusive license

to use S&C TripSaver II Service Center Conguration Software and/or other software

furnished with TripSaver II Cutout-Mounted Reclosers only upon acceptance of all

the terms and conditions of the seller’s end user license agreement set forth in

Price Sheet 155. Specically, for each conguration kit purchased, the user is entitled

to install and use S&C TripSaver II Service Center Conguration Software on no more

than two computers at a time.

4S&C Instruction Sheet 461-504

Safety Information

Understanding

Safety-Alert Messages

Several types of safety-alert messages may appear throughout this instruction sheet and

on labels attached to the TripSaver II Cutout-Mounted Recloser or in the TripSaver II

Service Center Conguration Software. Familiarize yourself with these types of messages

and the importance of these various signal words:

DANGER

“DANGER” identifies the most serious and immediate hazards which will likely

result in serious personal injury or death if instructions, including recommended

precautions, are not followed.

WARNING

“WARNING” identifies hazards or unsafe practices which can result in serious

personal injury or death if instructions, including recommended precautions, are not

followed.

CAUTION

“CAUTION” identifies hazards or unsafe practices which can result in minor

personal injury if instructions, including recommended precautions, are not followed.

NOTICE

“NOTICE” identifies important procedures or requirements that can result in

product or property damage if instructions are not followed.

Following

Safety Instructions

If you do not understand any portion of this instruction sheet and need assistance, contact

your nearest S&C Sales Ofce or S&C Authorized Distributor. Their telephone numbers

are listed on S&C’s website sandc.com, or call the S&C Global Support and Monitoring

Center at 1-888-762-1100.

NOTICE

Read this instruction sheet thoroughly and carefully

before configuring, installing or operating your

TripSaver II Cutout-Mounted Recloser.

Replacement

Instructions and

Labels

If additional copies of this instruction sheet are needed, contact your nearest S&C Sales

Ofce, S&C Authorized Distributor, S&C Headquarters, or S&C Electric Canada Ltd.

It is important that any missing, damaged, or faded labels on the equipment be replaced

immediately. Replacement labels are available by contacting your nearest S&C Sales

Office, S&C Authorized Distributor, S&C Headquarters, or S&C Electric Canada Ltd.

S&C Instruction Sheet 461-504 5

Safety Precautions

WARNING

Failureto properly configure aTripSaverIIrecloserin accordancewith applicable codes

and standards can result in misoperation or miscoordination, equipment damage,

personnel injury, or death.

Settings should be determined and approved by qualified personnel who are

familiar with the principles of selective coordination and system protection. S&C

Electric Company is not responsible for the misoperation or miscoordination of a

TripSaver II recloser resulting from improper configuration.

Make sure the TripSaver II recloser settings files are maintained in a secure manner

by properly trained personnel.

WARNING

The TripSaver II Cutout-Mounted Recloser MUST be de-energized and removed

from the utility pole before attaching the “corded” power module (power

module with ac adapter and extension cord) to the base of the TripSaver II recloser.

The corded power module is ONLY intended to be used for setup and data

collection when the TripSaver II recloser is de-energized and removed from the

utility pole. (To provide power to a TripSaver II recloser while it is mounted to the pole,

use the cordless power module, S&C catalog number 5954.) Failure to remove the

TripSaver II recloser from the utility pole before connecting the corded power

module can cause arcing, burns, electric shock, and death.

6 S&C Instruction Sheet 461-504

Shipping and Handling

A complete TripSaver II Conguration Kit, which weighs about 4 lbs. (1.8 kg) and works

with both 15-kV and 25-kV TripSaver II reclosers, consists of the following items enclosed

in a carrying case:

Packing

Ac adapter

TripSaver II power module

USB transceiver

Carrying case

Power outlet plug adapters

Extension cord for ac adapter

Blank adhesive labels

for user configuration

parameters [in pairs:

one white base and one

transparent overlay; 90

mm x 94 mm (3 inches

x 3 inches)]. Label

attaches to the left side

of the lower TripSaverII

recloser housing.

Figure 1. Components of the S&C TripSaver II Configuration Kit.

S&C Instruction Sheet 461-504 7

Shipping and Handling

Inspection Examine the shipment for external evidence of damage as soon after receipt as possible,

preferably before the carrier departs. Check the bill of lading to make sure the listed

shipping packages are present.

If there is visible loss and/or damage:

1. Notify the delivering carrier immediately.

2. Ask for a carrier inspection.

3. Note condition of shipment on all copies of the delivery receipt.

4. File a claim with the carrier.

If concealed damage is discovered:

1. Notify the delivering carrier within 15 days of receipt of shipment.

2. Ask for a carrier inspection.

3. File a claim with the carrier.

Also, notify S&C Electric Company in all instances of loss and/or damage.

Handling NOTICE

Handle the configuration kit with care. DO NOT drop the components or subject

any of their parts to undue stress during use. Only remove components from the

carrying case when they are ready to be used. After a TripSaver II recloser has been

configured, always return components to the carrying case for protection.

In addition, DO NOT drop a TripSaver II recloser or subject any of its parts to undue

stress during configuration or installation. Only remove a TripSaver II recloser from

the carton when it is ready for configuration or installation. After a TripSaver II

recloser has been configured, always return it to its carton until ready for installation.

8 S&C Instruction Sheet 461-504

Installing TripSaver®II Service Center Conguration Software Version 1.8

Installing TripSaver II Service Center Conguration Software Version 1.8 requires:

• A computer with Microsoft Windows 7 with Service Pack (SP) 1 with .NET framework

version 4.7 or later or Microsoft Windows 10 with .NET framework version 4.7 or later.

Note: If the .NET framework is missing, the software installer will automatically install

.NET framework. Microsoft has discontinued Windows 7 support.

• Administrative privileges for software installation.

TripSaver II Service Center Conguration Software (SCC) Version 1.8 is available for

download only to customers who have purchased the conguration kit. The latest release

is posted on the S&C Automation Customer Support Portal at sandc.com/en/support/SC-

customer-portal/. A username and password is required to log in to the portal. New

S&C customers must complete the form in the lower section of the Web page, and a new

username and password will be sent to them.

Customers who already have a password can click on the Log In to Secure Site

button. This opens the log-in page. See Figure 2.

Enter the username and password and click on the Log In button to log in to the portal.

Go to the “TripSaver II Workspace” section and download the latest installer

SCC1.8_Installer.exe file from the portal.

Computer

Requirements

Downloading Software

Figure 2. The customer portal log-in page.

S&C Instruction Sheet 461-504 9

Installing TripSaver®II Service Center Conguration Software Version 1.8

For each configuration kit purchased, the user is entitled to install and use

S&C TripSaver II Service Center Conguration Software on no more than two computers

at a time. Use the following steps to install the software:

STEP 1. Double-click on the downloaded installation le to self-extract and start the

process. The name of the software and its version number will appear. Click

on the Install button to proceed, or click on the Close button to quit the

installation process. See Figure 3.

Figure 3. Launching the SCC v.1.8 installation.

STEP 2. After clicking on the Install button, wait for the initialization to nish. The

installer will automatically install the correct .NET framework onto the

computer if .NET is missing. When .NET is successfully installed, the setup

wizard for the S&C TripSaver II Service Center Conguration Software will

open. See Figure 4.

Figure 4. The SCC v1.8 Installation Setup Wizard.

Software Installation

10 S&C Instruction Sheet 461-504

Installing TripSaver®II Service Center Conguration Software Version 1.8

STEP 3. Click on the Next button to continue, or click on the Cancel button to quit the

installation process.

STEP 4. The next dialog box to open allows the installer to select the installation folder.

Click on the Change button to select a specic destination folder, or use the

default folder shown. Click on the Next button to continue, or click on the

Cancel button to quit the installation process. Click on the Back button to go

back to the previous step. See Figure 5.

Figure 5. The SCC v1.8 Installation selecting destination folder.

Andere Handbücher für TripSaver II

Inhaltsverzeichnis

Andere S&C Hausautomation Handbücher

S&C

S&C PMX Leitfaden

Beliebte Hausautomation Handbücher anderer Marken

Truth Hardware

Truth Hardware Sentry II Bedienungsanleitung

FIBARO

FIBARO FGWPA-111 Bedienungsanleitung

Hezborg

Hezborg BGR8016B Bedienungsanleitung

MYDLINK

MYDLINK Pro Series Bedienungsanleitung

Panasonic

Panasonic KX-HNA101FX Bedienungsanleitung

GamaBit

GamaBit Houseper Bedienungsanleitung

nedis

nedis WIFILRF10C37 Bedienungsanleitung

Veho

Veho TA45 Bedienungsanleitung

Nexa

Nexa ZPR-111 Bedienungsanleitung

Vimar

Vimar 00801 Bedienungsanleitung

Leviton

Leviton 47604-F6 Bedienungsanleitung

EVERSPRING

EVERSPRING AN180 Bedienungsanleitung

Coltech

Coltech 18-1339 Bedienungsanleitung

IDS

IDS NXT vegas Leitfaden

Vimar

Vimar 03975 Bedienungsanleitung

iNels

iNels RFIM-20B Bedienungsanleitung

EVA Logik

EVA Logik ZW30 Bedienungsanleitung

Leviton

Leviton ODCØP-S0W Bedienungsanleitung