SanDisk Ultra Plus Bedienungsanleitung

SanDisk®Solid State Drive

Quick-Start Installation Guide

Upgrading your existing hard disk drive (HDD) to a new SanDisk Solid State Drive (SSD) is easy!

This guide provides quick instructions on how to upgrade your SATA-based desktop or notebook computer

HDD to a SanDisk SSD. We also cover cloning your data from your current HDD to your new SanDisk SSD

using cloning software.

Replacing your HDD with a solid state drive consists of three easy steps:

1. Connect your SanDisk SSD to your computer

2. Clone the data from your existing HDD to your new SanDisk SSD

3. Uninstall your HDD and replace it with your new SanDisk SSD

There are many options available for purchase, but in this guide we will use data cloning software

provided by Apricorn® to walk you through the data cloning process.

1. SATA data cable

(required for desktops computers only)

2. USB-to-SATA data cable

3. 3.5-inch mounting adapter and screws

(required for desktop computers only)

4. Phillips screwdriver

1

This guide applies to most solid state drives;

check the instructions included with your SSD

for more details.

NOTE:

Now that you have the required hardware and data cloning software, a few safety notes:

Simply follow these directions:

1. Carefully connect SATA end of the SATA-to-USB cable to your SanDisk SSD.

2. Connect the USB end of the SATA-to-USB cable to an available USB port on your computer.

Connecting Your SSD to Your Computer

That’s it, now you’re all set to clone your data!

SATA devices such as SSDs may draw more power than some computers are capable of

the data migration is complete.

NOTE:



same for both desktop and notebook computers.

Clone your data



process. (These may vary depending on the

software used.)

1. Run your preferred data cloning software.



Data Select.)

3. Select your source drive. (This is usually your



4. Next, select your destination drive. (This your

SSD connected to your computer by the

SATA-to-USB cable.)

4your current HDD is larger than the

capacity of your new SanDisk SSD,

your current HDD to reduce its

to exclude from the clone, such as

photos, videos, music or documents.

This is helpful when migrating from a

high capacity HDD drive to a smaller

capacity SSD.

NOTE:



click next to begin cloning your data. This

process will take some time depending on the



track of the progress by watching the cloning

status screen.

power cable plugged in during

this process.

NOTE:

6. The cloning software will prompt you when the



shut your computer down and proceed to

step three!



Before you begin, be sure to shut your computer down and disconnect the power cable.

This process will dier depending on whether you are installing your new SanDisk SSD in a desktop or

Replacing your HDD

Notebook Computer SSD Installation

NOTE: 



instructions).

3. Remove any brackets or adapters attached

to the current HDD and install them on your

new SanDisk SSD in the same way as they

were on your current HDD. (Note: This step

may not apply to every install, not all

notebook hard disk drives have additional

brackets or adapters.)

4. Align the connector pins on your SanDisk

SSD with the pins on the SATA connector in

the drive bay and carefully place the SSD

into the drive bay. (Note: Be sure to ﬁrmly

connect the SSD connector pins with the pins

on the SATA connector in your notebook

drive bay.)

6. Replace your battery and power cable, then power on your notebook computer.



is complete.

…And that’s it! Enjoy the speed of your new SanDisk SSD!

Desktop Computer SSD Installation

To install your SSD in a desktop computer, follow these steps: bay, you will not need to install the

3.5-inch mounting adapter.

NOTE:



cable is disconnected.



3. Locate your existing HDD.

4. Unplug the SATA data cable and SATA power cable from

your existing HDD and remove the drive from the bay.



bay and connect the SATA data cable and SATA power cable.



your computer.

screen indicating that the upgrade process is complete.

…And that’s it! Enjoy the speed of your new SanDisk SSD!







your mounting adapter.



as a backup drive.

NOTE:

the trademarks of their respective holder(s).

www.sandisk.com/go-SSD

www.sandisk.com/wug

Dieses Handbuch passt für folgende Modelle

Andere SanDisk Lagerung Handbücher

SanDisk

SanDisk SSD X100 Bedienungsanleitung

SanDisk

SanDisk ImageMate CompactFlash Bedienungsanleitung

SanDisk

SanDisk CompactFlash Bedienungsanleitung

SanDisk

SanDisk SDMB-16-470 - 16 MB MultiMedia Card Bedienungsanleitung

SanDisk

SanDisk DMS platform Bedienungsanleitung

SanDisk

SanDisk G3 Bedienungsanleitung

SanDisk

SanDisk TrustedSignins Bedienungsanleitung

SanDisk

SanDisk Cruzer Contour Bedienungsanleitung

SanDisk

SanDisk iXpand Bedienungsanleitung

SanDisk

SanDisk iNAND eMMC Bedienungsanleitung

SanDisk

SanDisk Connect Bedienungsanleitung

SanDisk

SanDisk 80-11-01546 Bedienungsanleitung

SanDisk

SanDisk SanDisk Cruzer Bedienungsanleitung

SanDisk

SanDisk SSD 5000 Bedienungsanleitung

SanDisk

SanDisk PROFESSIONAL G-RAID SHUTTLE 4 Bedienungsanleitung

SanDisk

SanDisk MobileMate Memory Stick Plus Bedienungsanleitung

SanDisk

SanDisk SSD Ultra ATA Montageanleitung

SanDisk

SanDisk CompactFlash Bedienungsanleitung

SanDisk

SanDisk INAND Bedienungsanleitung

SanDisk

SanDisk 4gb Compact Flash Ultra II - 4gb Ultra II Compact Flash Memory... Bedienungsanleitung

SanDisk

SanDisk Cruzer Professional Bedienungsanleitung

SanDisk

SanDisk microSDHC Bedienungsanleitung

SanDisk

SanDisk CompactFlash 5000 Bedienungsanleitung

SanDisk

SanDisk pSSD-P2 Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung