Sangean BTS-102 Bedienungsanleitung

BTS-102

The aptX® mark and the aptX logo are trademarks of CSR

plc or one of its group companies and may be registered in

one or more jurisdictions.

The Bluetooth® word mark and logos are registered

trademarks owned by Bluetooth SIG, Inc. and any use of

such marks by SANGEAN ELECTRONICS INC. is under

license.

Source button

DBB button

Previous track button

Bluetooth/Call answer-hangup button/Play and Pause

button

Next track button

Volume up/down button

Bluetooth/Aux-in indicator

Battery status/Volume indicator

DBB on/off indicator

Speaker

Aux in socket

DC In

USB charging socket

Power button

Key lock

NFC detection tag

Microphone

Controls

Opening the cover

The cover is designed to protect the speaker from damage

and can also serve as a stand for the speaker. Turn

over the cover on the rear of the speaker and make sure

the magnets on the front cover and the rear cover hold

together as shown in the gure.

This unit operates on a built-in Li-on battery that can be

recharged using the AC power adaptor. The AC power

required for this unit should be 12volts DC at 1.5A center

pin positive. Before operating the speaker for the rst time

please fully charge the battery.

Insert the adaptor plug into the DC socket on the left side

of the speaker. ThenPlug the adaptor into a standard

mains socket outlet and the speaker will begin charging

the built in battery. Charging time is approx. 3.5hours

with speaker off and 8 hours with speaker on. The battery

indicator on the front panel will flash when the battery

charging is in progress. After the speaker is fully charged

the battery indicator will remain in solid white. Once fully

charged the battery will power your speaker for up to 20

hours depending on the volume level. Reduced power,

distortion, ‘stuttering’ sound or battery power indicator in

low are all signs that the battery needs to be recharged.

The AC adaptor should be disconnected from the main

supply when not in use.

IMPORTANT:

The mains adaptor is used as the means of connecting the

radio to the mains supply. The mains socket used for the

radio must remain accessible during normal use. In order

to disconnect the radio from the mains completely, the

mains adaptor should be removed from the mains outlet

completely.

Using the AC power adaptor to charge

the unit

Before power-on the speaker, make sure to set the key

lock to its off position (down).

There are two ways to power on your speaker.

● You can press the Power button to turn on the speaker.

● In addition, the speaker can be powered on via NFC:

Turn on your NFC feature on your NFC-enabled device >

Hold your NFC-enabled device directly against BluPad’s

NFC tag for 2 seconds. Once the speaker is powered on

successfully, the speaker will make a sound to conrm.

Note:

1. Some devices may ask for conrmation from the user.

2. Your speaker will automatically shut off if no operation is

performed or no music is playing for about 15 minutes.

Power on the speaker

To check the current battery level, press and hold the

Power button to switch on the speaker and the battery

status indicator will show on the front panel in solid white

indicating the current battery level.

Note: The greatest working life from the built-in battery will

be obtained if it is kept topped up by recharging after each

use of the speaker, even if it is only partially discharged.

The battery’s working life will be reduced if the product is

left in a discharged condition for a long period of time.

Battery status indicator

Battery is fully charged (more than

75% of battery capacity)

Battery is partially charged (between

50-75% of battery capacity)

Battery is partially charged (between

25-50% of battery capacity)

Low battery and charging is needed

(less than 25% of battery capacity

Battery life can be ran out any minute

and charging is needed immediately.

( )

USB power supply socket

You need to pair your Bluetooth device with your BluPad

(BTS-102) before you can auto-link to play/stream

Bluetooth music through your Bluetooth speaker. Paring

creates a `bond' so two devices can recognize each other.

This jack can be used to charge a mobile phone or any

other device that uses less than 1000 mA of DC current.

Charging will only occur when the speaker is plugged into

an outlet. USB power socket will not charge when the

speaker is running off of a battery pack.

Note: Ensure the specification of your external device

such as mobile phone, mp3 player or iPod is compatible

with the speaker. Please read instruction manual of your

external device before charging.

Pairing and connecting a device to the

speaker

Pairing and playing your Bluetooth

device for the rst time

1. Before turning on the speaker, make sure the key lock is

switched off (down).

2. Press the Source button until the Bluetooth/Aux in

indicator turns blue followed by a confirmation sound.

The indicator flashes fast flashing blue indicating the

speaker is discoverable.

3. Activate Bluetooth on your device according to the

device's user manual to link to the speaker. Locate the

Bluetooth device list and select the device named

‘SANGEAN BLUPAD.’ With some mobiles (which are

equipped with earlier versions than BT2.1 Bluetooth

device), you may need to input the pass code “0000”.

4. Once connected, there will be a beep sound and the

Bluetooth indicator will remain in solid blue. You can

simply select and play any music from your source

device. Volume control can be adjusted from your source

device, or directly from the speaker.

5. Use the controls on your Bluetooth-enabled device or on

the speaker to play/pause and navigate tracks. .

(Note: If you press the Bluetooth/Call answer-hangup

button twice in quick succession, your BluPad will redial

the last phone number made on your smartphone.)

Note:

1. If 2 Bluetooth devices, pairing for the first time, both

search for your speaker, it will show its availability on both

devices. However, if one device links with this unit rst,

then the other Bluetooth device won't nd it on the list.

2. If you take your source device out of range, the

connection will be temporarily disconnected to your radio.

Your radio will automatically reconnect if the source

device is brought back in range. Be aware that during

the period of disconnection, no other Bluetooth device

can pair or link with your speaker.

3. If ‘SANGEAN BLUPAD” shows in your Bluetooth device

list but your device cannot connect with it, please delete

the item from your list and pair the device with your speaker

again following the steps described previously.

4. The effective operation range between the system and

the paired device is approximately 10 meters (30 feet).

Any obstacle between the system and the device can

reduce the operational range.

5. Bluetooth/NFC connectivity performance may vary

depending on the connected Bluetooth devices. Please

refer to the Bluetooth capabilities of your device before

connecting to your radio. All features may not be

supported on some paired Bluetooth devices.

Andere Handbücher für BTS-102

Inhaltsverzeichnis

Sprachen:

Andere Sangean Tragbare Lautsprecher Handbücher

Sangean

Sangean BTS-102 Bedienungsanleitung

Beliebte Tragbare Lautsprecher Handbücher anderer Marken

Monster

Monster Rockin Roller 2 Bedienungsanleitung

Blueant

Blueant BLUESONIC Bedienungsanleitung

Altec

Altec 730C Bedienungsanleitung

Aiwa

Aiwa BST-330 Bedienungsanleitung

Prestigio

Prestigio PIS1 Bedienungsanleitung

Akai

Akai AWS08BK Bedienungsanleitung

Philips

Philips BT6700 Bedienungsanleitung

Wren

Wren V5BT Bedienungsanleitung

Sven

Sven PS-320 Bedienungsanleitung

Urban revolt

Urban revolt Streetbox Bedienungsanleitung

Philips

Philips BT4000 Produktinformationsblatt

Philips

Philips sbm130 Bedienungsanleitung

Gembird

Gembird TD-SPKBT-04 Series Bedienungsanleitung

Panacom

Panacom monsoon Bedienungsanleitung

Lenovo

Lenovo speaker M0520 Bedienungsanleitung

Mackie

Mackie THUMP GO Bedienungsanleitung

Trevi

Trevi XR 400 APP Bedienungsanleitung

Trevi

Trevi XF 4200 DJ Bedienungsanleitung