Sangean H202 Bedienungsanleitung
中文
GB
Version 1
H202
1
GB
Features
1. Built-in AM/FM antenna for best reception
2. 10 presets (5 each wave band)
3. Water resistant up to JIS7 standard
4. Auto seek stations
5. Large and easy to read LCD display
6. Easy to x bracket and hanger
7. Battery power indicator
8. Clock
9. Adjustable sleep timer
10. Adjustable short timer
11. Emergency LED illumination (Torch)
12. Emergency Buzzer
13. Water-resistant 3 inches speaker
2
3
GB
LCD Display
Preset stations
(preset 1: Bluetooth pair button / preset 3: setting tuning step)
Nap timer (Short timer)
Power button
Band and Time Set button
Tuning Control
Volume Control
Speaker
DC IN socket
Hanger Ring
Emergency Buzzer
Torch button
Torch
Multi Purpose Handle
Bracket Holder
Battery Cover
FM wire antenna compartment
Controls
2
1
3
4
5
7
15
14
13
12
11
10
9
6
8
17
16
LCD Display
Battery Power Status
Volume level
Auto Off status
Short Timer set
Memory number and seconds
Time and Frequency
Band indicator
Bluetooth indicator
G
F
E
D
C
B
A
H
4
Installing batteries
1. Position the radio face down on a soft surface.
2. Remove the catch as shown and lift out the battery cover.
3. Insert 2 x “D“ size/UM-1/LR20 batteries.
4. Replace the battery cover and catch.
5. Reduced power, distortion, a “stuttering“ sound are all signs that
the batteries may need replacing. The batteries should be replaced
when the battery indicator ashes and E shows in the display.
6. If the radio is not to be used for any extended period of time, it is
recommended that the batteries are removed from the radio.
5
GB
Using the AC adaptor ( not supplied )
1. Remove the rubber cover of DC in socket on the left hand side
of your radio.
2. Insert the adaptor plug into the DC socket.
3. Plug the adaptor into mains socket outlet. Whenever the adaptor
is used, the batteries are automatically disconnected.
The AC adaptor should be disconnected from the mains supply and
the radio when not in use.
Note:
For safety purpose, DO NOT use AC adaptor in the shower
room. Use the batteries only.
Setting the clock
1. The clock will start running when the batteries are installed or
when the radio is connected to the mains supply. The display
will show “ - : - - “.
2. The time can be set with your radio switched off or on.
3. Press and hold down the Time Set button for approx.
2 seconds until the hours digits ash in the display with a beep.
4. Press the Tuning Up/Down buttons to set the required hour.
5. Press the Time Set button, the minute digits will ash in
the display.
6. Press the Tuning Up/Down buttons to set the required minute.
7. Press the Time Set button to complete time setting.
The second will start to count.
6
Operating your radio
Your radio is equipped with three tuning methods – Manual Tuning,
Search tuning and Memory preset tuning.
Manual Tuning
1. Press the Power button to turn on the radio.
2. Select the required waveband by repeatedly pressing the Band
button. For FM waveband, pull out and extend the FM wire antenna
located in the battery compartment to get best reception.
For MW (AM) waveband, rotate the radio for best reception.
3. A single press on either Tuning up or Tuning down buttons will
change the frequency in the following increments:
FM: 100 or 200 kHz (USA version)
50 or 100 kHz (standard version)
AM (MW): 9 or 10 kHz
4. When the waveband end is reached, the radio will continue tuning
from the opposite waveband end.
5. Press the Volume Up/Down buttons to the required level.
6. To switch off your radio, press the Power button. The display will
show OFF.
7
GB
Search tuning
1. Press the Power button to turn on the radio.
2. Press the Band button to get required waveband, then extend and
position telescopic aerial (FM) or rotate the radio (AM).
3. Press and hold down either Tuning up or Tuning down buttons for
more than 0.5 seconds to commerce Search tuning.
4. The radio will search and stop automatically when it nds a station
of sufcient strength.
5. When the waveband end is reached, the radio will continue tuning
from the opposite waveband end .
6. Press the Volume Up/Down buttons to the required level.
7. To switch off your radio, press the Power button. The display will
show OFF.
8
Memory preset tuning
Storing stations in preset memories
There are 5 presets for each waveband.
1. Press the Power button to turn on the radio.
2. Tune to the required station using one of the methods previously
described.
3. Press and hold down required preset until the radio beeps (more
than 2 seconds). The preset number will appear with a M (memory)
and the station will be stored under the chosen preset button.
4. Repeat the procedures for the remaining presets.
5. Stations stored in preset memories may be overwritten by
following the above procedures.
9
GB
Recalling preset stations
1. Press the Power button to turn on the radio.
2. Select the required waveband by pressing the Band button.
3. Momentarily press the required Preset button, the preset number
and station frequency will appear in the display.
Software version
The software display cannot be altered and is just for your refer-
ence.
1. Turn off the radio.
2. Press the Preset button 3/step button for 2 seconds until the
software version number (e.g. P01) shown on the display.
FM range setting
3. After the display of software version, the display will automatically
change to FM range setting. Press the Tuning up/down button to
choose the desired selection and press the Preset button 3/step
button to conrm the setting. Options for FM range are as following:
F00: 87.5-108 MHz
F01: 76-90 MHz
F02: 64-108 MHz
F03: 76-108 MHz
Inhaltsverzeichnis
Andere Sangean Radio Handbücher
Sangean
Sangean HDR-1 Bedienungsanleitung
Sangean
Sangean U2 Bedienungsanleitung
Sangean
Sangean DPR-26BT Bedienungsanleitung
Sangean
Sangean PR-D3L Bedienungsanleitung
Sangean
Sangean DDR-63 - WIFI INTERNET RADIO-TUNERS Benutzerhandbuch
Sangean
Sangean DT-120 Betriebsanleitung
Sangean
Sangean PR-D18 Bedienungsanleitung
Sangean
Sangean WFR-2D Bedienungsanleitung
Sangean
Sangean WFT-1 Bedienungsanleitung
Sangean
Sangean PT-633 Bedienungsanleitung
Sangean
Sangean POCKET 390 Bedienungsanleitung
Sangean
Sangean WFR-20 Bedienungsanleitung
Sangean
Sangean SR-25 Bedienungsanleitung
Sangean
Sangean ATS-909 Bedienungsanleitung
Sangean
Sangean WFR-1 - DATASHEET 3 Bedienungsanleitung
Sangean
Sangean DPR-99 Plus Bedienungsanleitung
Sangean
Sangean PR-D4 Bedienungsanleitung
Sangean
Sangean SG-106 Bedienungsanleitung
Sangean
Sangean WFR-28C Bedienungsanleitung
Sangean
Sangean PT-633 Bedienungsanleitung
