Saniwise F6 Bedienungsanleitung

Bidet Seat F6 User Manual

Thank you for purchasing Saniwise Bidet Seat. Please read through this manual

carefully to ensure the safe use of your product.

Keep this manual in a safe place for your future reference.

Contents

Parts and What’s in the Box

Parts

What’s in the Box

Self-diagnosis and Troubleshooting

Cleaning and Dismantling

Maintenance

Warranty Record

Saniwise Warranty

7Extra Installation Tips

Installation

Caution

Preparation

Installation Procedures

Connecting Water Inlet Hose

Functions

WASH (REAR WASH)

BIDET (FRONT WASH)

STOP

Water inlet on the left

Parts and What’s in the Box

Parts

Bowl

Water inlet hose

Shutoff valve

T-shaped adapter

Lever

Water tank

Water supply hose

Seat cover

Seat

Wash nozzle

Bidet nozzle

Dismantle button

1. Bidet seat and lid 2. Installation template

Connecting bolts x2

Sliding plates x2

4. T-shaped connector 5. Water inlet hose 6. User Manual

User Manual

3. Fixing components

Expansion nuts x2

Filter

Note

There are two methods to install the Saniwise Bidet Seat. It is recommended that you use expansion

nuts. You can also use butterfly nuts. Please choose the appropriate installation method according

to your specific installation needs.

Nuts x2

Adapter plate x1

What’s in the Box

Caution

1. The water pressure limit ranges from 10 to 110 PSI. Please use as instructed.

2. The water shutoff valve should be near where the product can be installed and dismantled.

Please read the following instructions carefully and install your Saniwise Bidet Seat

properly.

Preparation

Insert the connecting bolts into the sliding plates.

Insert the connecting bolts into the holes of the sliding plates, as shown in the figure below.

2. Insert the connecting bolts with the sliding plates into the adapter plate.

Insert the connecting bolts with the sliding plates into the holes of the adapter

plate, as shown in the figure below.

Installation Procedures

Installation Method One (Recommended)

1. Dismantle the old bidet seat and lid.

Loosen the hinge and remove the old bidet seat and lid.

Keep this side with FRONT up

Installation

template *Butterfly nuts are only used for

the optional installation method two.

Installation template

Installation Method Two

1. Dismantle the old bidet seat and lid, and place the installation template on the ceramic, as described in step 1 and step 3 of the

installation method one.

2. Put the adapter plate over the toilet seat’s mounting holes in the ceramic of the connecting bolts with adjusting pieces. Screw the nuts

from underneath the toilet. Then tighten them to secure the adapter plate. Refer to the step 4 of the installation method one.

3. Complete the following installation procedures, as described in step 5 and step 6 of the installation method one.

2. Install the expansion nuts.

Insert the expansion nuts into the holes of the ceramic. Be

sure to firmly press down so the top of the expansion nut is

flush with the ceramic toilet surface.

3. Install the installation template.

4. Fix the adaptable panel.

Attach the adapter plate. Attach the adapter plate in the toilet

seat holes. Adjust the connecting bolts’ and adjusting pieces’

position to line up the connecting bolts to the expansion nuts.

Then tighten them to secure the adapter plate.

5. Remove the installation template. 6. Mount the Saniwise Bidet Seat.

Keep the fixing slots under the Saniwise Bidet Seat aiming

at the slots on the adaptable panel. Push the Saniwise Bidet

Seat to the end. Now, the Saniwise Bidet Seat is installed

successfully.

Fixing slots under the

Saniwise Bidet Seat

Bidet seat and lid

Place the installation template on the ceramic.

1. Turn off the water supply valve. 2. Unscrew the water supply hose from the water

tank. Place a towel below the tank to catch any

dripping water.

3. Using finger nut, attach the T-shaped connector

to the water tank where you removed the water

supply hose.

4. Attach the water supply hose to the bottom of

the T-shaped connector.

5. If they have become loose during shipping,

press the filter screen and rubber washer into

the connectors at the ends of the white water

inlet hose. Connect the white water inlet hose to

the bidet seat and the other end to the T-shaped

connector and tighten snugly. Do not over

tighten.

6. Slowly turn on the water valve to check if

there is any water leakage.

Unscrew to remove

Finger nut

Washer

Filter

Connecting Water Inlet Hose

Please remove the regulator cover and regulator O-ring under the following conditions:

Caution: Must use the regulator cover and regulator O-ring when the water pressure

is greater than 15 PSI.

How to do:

1. Take out the regulator with pliers and other tools.

2. Remove the regulator cover and regulator O-ring except the sealing O-ring.

3. Insert the regulator component into the inlet pipe.

a. When the water pressure is lower than 10 PSI.

b. When the nozzle cannot work normally and water pressure is low.

Regulator

cover

Regulator

O-ring

Sealing

O-ring

7. Wipe the hoses and connectors thoroughly with a towel and carefully observe for any leaks for at least

10 minutes. Tighten any connectors gently until leakage stops. If any leaks continue, turn off the water

supply and check older hoses for damaged rubber O-rings and replace them if necessary.

*Optional, only do the following if water pressure is too low.

Warning

1. Do not lift the product with the seat cover and seat open.

This may damage the bidet seat.

2. Do not use with hot water where temperature is higher

than 40℃/104℉.

Extra Installation Tips

1. This will not apply to most customers, however, if you happen to have a rigid water

supply line to your toilet tank you will need to replace that with a flexible steel braided

water supply hose which can be found at any hardware store, Home Depot, Lowe's etc.

The addition of the "T" connector will make an existing "rigid" hose too long. We

recommend you purchase the same length flexible hose as your rigid line +/- an inch.

It does not need to be exact because it's flexible, but too long may look unattractive.

2. There is a white rubber hose that is sealed in a plastic bag. Occasionally the rubber

gasket will fall out of the hose end during shipping. Just make sure you put it back in

place if yours fell out, or if you find it loose in the bag with the hose.

3. If you are not using the nuts, be sure to firmly push the two adapter plate anchors all

the way into the two holes on your toilet bowl to ensure the adapter plate fits tightly to

your toilet after tightening the stainless steel screws.

4. In most cases everyone is happy with the pressure that the cleaning jets put out. If for

any reason you would like a stronger stream, please refer to page 6 in the instructions

and it will explain how to remove the pressure regulator and dramatically increase the

pressure.

If you still need help, feel free to send us an email at [email protected].

Functions

STOP

1) During WASH or BIDET status, rotate the lever to the vertical

position to stop the freshwater spray.

2) The nozzle moves back to the original position.

3) The water volume decreases while turning the lever towards the vertical

position. It will totally shut off when the lever is on the vertical position.

WASH (REAR WASH)

1) Turn the lever clockwise from the vertical position.

2) The nozzle for rear wash extends forward, and the freshwater spray

function starts.

3) The water volume decreases while turning the lever towards the vertical

position. It will totally shut off when the lever is on the vertical position.

1) Turn the lever counterclockwise from the vertical position.

2) The nozzle for feminine Bidet (front wash) moves forward and the

freshwater spray function starts.

3) The water volume decreases while turning the lever towards the vertical

position. It will totally shut off when the lever is on the vertical position.

Note that the front wash nozzle is slightly longer when fully extended and

directs spray more in the forward direction.

BIDET (FRONT WASH)

Inhaltsverzeichnis

Andere Saniwise Toilette Handbücher

Saniwise

Saniwise F8 Bedienungsanleitung

Beliebte Toilette Handbücher anderer Marken

Toto

Toto Washlet TCF4911 Series Bedienungsanleitung

Kohler

Kohler K-6419 Bedienungsanleitung

Grohe

Grohe Sensia ARENA Bedienungsanleitung

Kohler

Kohler K-5171K Montageanleitung

Geberit

Geberit AQUACLEAN MERA CLASSIC Bedienungsanleitung

Kohler

Kohler K-24097X Montageanleitung

Better Bathrooms

Better Bathrooms BUN/BeBa 27555/78725 Bedienungsanleitung

American Standard

American Standard CONCEPT Cube TF-2704 Bedienungsanleitung

BIOLAN

BIOLAN ECO Stücklistenhandbuch

Thetford

Thetford C260 Series Bedienungsanleitung

KELISS

KELISS T162A Series Bedienungsanleitung

Kohler

Kohler K-22241K Montageanleitung

Kohler

Kohler ESCALE K-32771T-NS Bedienungsanleitung

BIOLAN

BIOLAN GARDEN TOILET Stücklistenhandbuch

washloo

washloo Prestige Bedienungsanleitung

JABSCO

JABSCO 37010 Series Bedienungsanleitung

Drive

Drive TSE 150 Bedienungsanleitung

Olympia

Olympia EPOQUE 69209 Bedienungsanleitung