SANY SY135C Bedienungsanleitung
SY135C
QUICK
START
GUIDE
SY135C QUICK START GUIDE
01
SY135C Display
05
06
18
17
16
19
20
21
22
07
08
09
10
11
12
13
14
15
24
01 GPS Active
02 Fuel Level
03 Buzzer Cancelled
04 Work/Throttle Indicator
05 Time/Date
06 Automatic DPF Regen
07 DPF Regen Inhibit Warning
08 Engine Fault Warning
09 Engine Pre Heat
10 Engine Stop Warning
11 Engine Torque De-rate
12 Engine Torque De-rate 25%
13 Engine Torque De-rate 75%
14 Work Mode
15 Daily Work Hours
16 AdBlue Tank Level
17 AdBlue Tank Level Below 2%
18 Manual DPF Regen Warning Lamp
19 Adblue Level Below 10%
20 Battery Charge Warning
21 Aftertreatment Error
22 SWL Alarm
23 Engine Coolant Temperature
24 Throttle Position
25 Total Work Hours
26 Service Menu
27 Automatic Idle
28 Travel Speed
29 Main Menu
01 03 04
02
25
26 27 28 29
23
02
Work Mode
S
H
L
B
Operation
Standard / Normal operation.
Heavy Duty Mode. For when additional power is required for heavy applications. Power Boost.
Light Duty / Lifting. For when fine control is required.
Breaker. This mode prioritises hydraulic oil flow to auxiliary lines over general machine services.
If a machine is left in this mode and then an operator tries to dig, the machine may feel
underpowered and sluggish.
Work Modes
01 The machine work mode is
enabled by selecting the desired
mode on the touch screen display.
Press the mode select icon to
cycle through options.
01
SY135C QUICK START GUIDE
03
Quick Hitch Process (PT 1)
01 Select Main
Menu Icon
02 Select Quick
Change
03 Select Unlock
Icon
(Buzzer will sound)
01
02
03
04
Quick Hitch Process (PT 2)
01 Select Bucket
Removal Icon
02 Select right hand
button on left hand
lever control and
press throughout
the entire
detachment
process
03 Crowd the bucket
fully in to allow
the bucket to
detach. Whilst still
pressing the
button, connect the
next attachment
01
02 03
Note: Please be aware that the Quick Hitch process may vary if a third party attachment system is fitted.
SY135C QUICK START GUIDE
05
3
6
Tool Selection
01 Select Main
Menu Icon
02 Select Implement
Selection icon
03 Select required
attachment from
the menu
1. Bucket
2. Breaker
3. Grab/Clam shell
4. Rotator grab
5. Flail
6. Grapple
7. Grapple with rotate
8. Auger
01
02
1 2
4 5
7 8
03
06
Tool Set Up
01 Select the required
tool from the menu
02 Select Tool Set Up 03 SET UP
RL & RR = High Flow
(Breaker Lines)
LL & LR = Low flow
(Rotation Lines)
Press +/- icons to increase
or decrease flow on desired
circuit.
Press Tick Icon to save settings
*Figures on the display screen are a guide. All flows should be verified using a flow meter when the attachment is installed.
01
01
OPERATION
LL = Left lever slide left
LR = Left lever slide right
RL = Right lever slide left
RR = Right lever slide right
01 02
02 03
Left Lever Right Lever
SY135C QUICK START GUIDE
07
3
6
Exhaust Regeneration
01 The machine will run an auto regen as required
to clear soot from the exhaust system.
For the regen to commence the machine must
meet certain parameters with regards to
temperature.
When the Auto Regen light illuminates continue
to work the machine normally until the regen
has completed.
3
6
02 A regen can be inhibited in the event that
carrying out the process with high exhaust
temperatures may cause a health and safety
concern, for example the machine is working
next to flammable material.
To inhibit the regen select the Main Menu and
then select the multi-function panel.
01
02
08
3
6
01 Select the Regen Inhibit icon and then
select Escape.
3
6
02 The regen will stop and the Regen Inhibit light
will illuminate on the display.
The machine can now be moved to a safe area
to allow the process to continue.
*DO NOT inhibit regens unnecessarily.
*All inhibits are recorded within the machine ECU.
*Multiple inhibits will lead to a service regen
being required or may result in damage to the
exhaust system. Damage caused in this way is
NOT covered by warranty.
01
02
SY135C QUICK START GUIDE
09
Manual Regeneration
1 2
Manual regeneration is only available if the machine requests one. The Manual Regen light will flash
in the top right corner of the display. It will only do so if automatic regenerations have been inhibited
or cancelled.
01 03
02
01
01 To carry out a
manual regen the
machine must be
up to operating
temperature.
The safety lever
must be down.
The throttle dial
must be on 1.
Select the Main
Menu icon.
Select the
Multi-Function
icon.
02 Select the Manual
Regen button.
The machine will
now run through
the process
automatically.
03 The Manual Regen
light will stay
illuminated
throughout the
process.
DO NOT leave the
machine unattended.
DO NOT select any
services or operate
the machine.
DO NOT open the
bonnet. Exhaust
temperatures may be
in excess of 700
degrees centigrade.
Andere Handbücher für SY135C
1
Inhaltsverzeichnis
Andere SANY Bagger Handbücher
SANY
SANY SY265C LC Bedienungsanleitung
SANY
SANY SY16C Bedienungsanleitung
SANY
SANY SY75 Bedienungsanleitung
SANY
SANY SY26U Bedienungsanleitung
SANY
SANY SY35U Bedienungsanleitung
SANY
SANY SY135C Bedienungsanleitung
SANY
SANY SY95C Bedienungsanleitung
SANY
SANY SY500H Bedienungsanleitung
SANY
SANY SY50U Bedienungsanleitung
SANY
SANY SY115C9 Leitfaden
