Sanyo FX-02 Bedienungsanleitung
INSTRUCTION MANUAL
(P.
I-
P
.
5)
@~~B~~(P
.
6-
P.10)
MANUAL DE INSTRUCCIONES
(P.
ll-
P.
15)
Full Auto Reverse Cassette
Car Stereo with AM/FM
STEREO Synthesizer Tuner
FX-02, FX-03
Thank you for purchasing SANYO’s FX-02, 03 cassette car stereo player.
For proper operation and performance, read this instruction manual carefully.
n
CONTROL AND OPERATION
1) On-Off/Volume knob
(OFF/VOL)
2) Balance control knob
(BALI
3) Tone control knob
(TONE)
4) Tuning button (A, v
1
Manual Tuning
If the right button (A) or the left button
(v)
is pushed, the radio frequency on
the digital display will count up or down.
Auto Tuning
Depressing and hold down the TUNING button for half a second will start auto-
matic tuning.
The tuning process will be stopped when a strong signal is received.
5) Band button
(B)
Select the desired radio band with the BAND select button. The radio frequency
FMl,
FM2 or AM will be shown on the digital display.
Preset Scan button (P. SC
)
By pushing the preset scan button, you can tune in sequence, the memorized or
preset stations for 5 seconds for each preset button 1 through 6 automatically.
To stop scanning, touch this button again or the desired preset button.
-l-
.
.
6) Auto store button
(AST)
Pressing momentary Auto Store Button, AST mode is engaged and AST indica-
tor lights. Pressing this button for more then 2 sec., up to 6 stations are automa-
tically preset in the AST memory (6 AM and 12 FM).
7) Preset buttons (1 to 6)
For presetting station, the unit has an electric memory circuit which is capable
of memorizing 6 AM, 12 FM and 18 (AM and FM) Auto Store Stations for a
total of 36 stations.
To memorize a program, tune in a desired station, and press and hold down the
desired preset button for at least 1 seconds.
8) Distant/Local select button
(DX
)
For strong local FM signal reception, the distant/local select button (DX) should
be in the local position. For a weak distant signal, the distant/local select button
(DX)
should be in the distant position. The distant position (DX) will be shown
on the digital display.
9) Cassette Slot
10) EJECT button
(4
)
To eject the cassette, depress this button.
11) Fast Forward, Fast Rewind and Reverse button
(
44
,
H
,
4,
)
To advance or rewind the tape at high speed, depress
(
H
)
button or
(
44
)
button. To stop and return to normal playback, lightly press the button which is
not pressed.
Reverse button
To reverse the tape direction, depress both buttons at the same time.
12) Tape selector button
(MTL)
Set the tape select button
(MTL)
to select the proper
equalization
for the type
of tape to be used. Press the button for
Metal/FeCr/CrOz
tape. Re-press the but-
ton for Normal tape.
13) LCD display
-2-
n FX-02: INSTALLATION
Stopper
1. Insert mounting bracket into DIN-standard cutout 182 x 53 mm in the dashboard
or a console.
The side marked “UP” should be up.
2. Bend the stoppers of the mounting bracket with a screwdriver, and secure the
bracket firmly to the dashboard.
3. Fix the mounting bracket by using the mounting hardware supplied.
4. Insert the set into the mounting bracket until it locks.
SET REMOVAL
1. Push the upper edge on left sides of the handle to raise the handle.
2. Pull the handle to remove the set.
-3-
n FX-03: INSTALLATION
1. Insert mounting bracket into DIN-standard cutout 182 x 53 mm in the dashboard
or a console.
2. Bend the stoppers of the mounting bracket with a screwdriver, and secure the
bracket firmly to the dashboard.
3. Insert the set into the mounting bracket until it locks.
SET REMOVAL
1. Insert the supplied pin into the small hole located upper left on the front panel.
2. Pull out the set by this pin and then moving it up.
Pin
n
SPEAKER CONNECTIONS
FX-02, FX-03 1
To the
+
12V
power termi-
nal which is
energired
when
the ignition key is in the
accessory position.
n
MAINTENANCE
1. When the car stereo is not in use, remove the audio cassette from the tape player.
2. Cassette shells may warp, keep them out of direct sunlight. The shell should not
be exposed to heat exceeding 130 degrees.
3. Never place an audio cassette tape in the vicinity of a strong magnetic field.
4. When replacing the fuse, make sure to use a new 2 ampere (maximum rating) fuse
for main power,
If a fuse blows again, recheck. wiring or have the unit bench tested at a service
station.
5. Clean the tape head, pinch roller and capstans at least once a month using a quali-
ty audio head cleaning cassette.
-5-
-6-
-7-
n
Fx-02:
g$g
-8-
-9-
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Sprachen:
Andere Sanyo Autoempfänger Handbücher
Sanyo
Sanyo FXD-880RDS Bedienungsanleitung
Sanyo
Sanyo FXD-680GD Bedienungsanleitung
Sanyo
Sanyo FXR-61GB Bedienungsanleitung
Sanyo
Sanyo FXR-725GD Bauanleitung
Sanyo
Sanyo FXCD-1100 - Radio / CD Bedienungsanleitung
Sanyo
Sanyo F-8501 Bedienungsanleitung
Sanyo
Sanyo EX-W22 Bedienungsanleitung
Sanyo
Sanyo MCX-400 Bedienungsanleitung
Sanyo
Sanyo FXCD-550 - Radio / CD Bedienungsanleitung
Sanyo
Sanyo EXCD-1000 Bedienungsanleitung
Sanyo
Sanyo ECD-T1560 Gebrauchsanweisung
Sanyo
Sanyo FXR-45GD Bedienungsanleitung
Sanyo
Sanyo T1443 - ECD Radio / CD Bedienungsanleitung
Sanyo
Sanyo FXC-503LD Bedienungsanleitung
Sanyo
Sanyo FXD-MP900 Bedienungsanleitung
Sanyo
Sanyo CDF-201G Bedienungsanleitung
Sanyo
Sanyo FXD-680GD Bedienungsanleitung
Sanyo
Sanyo FXD-770GD Bedienungsanleitung
Sanyo
Sanyo FXCD-550 - Radio / CD Bedienungsanleitung
Sanyo
Sanyo FX12 Bedienungsanleitung
