Sanyo LNS LNS-W03 Gebrauchs- und Pflegehandbuch

Type of the Cabinet (1) See Page 2

LCD PROJECTOR LENS

MODEL NO. LNS-W03

LENS REPLACEMENT

AND INSTALLATION PROCEDURES

NOTES ON REPLACEMENT AND INSTALLATION

The procedures and the needed pars for lens installation depend on the type of

cabinet. Before installing or replacing the lens, make sure the type of cabinet and be

sure to refer to the Installations corresponding with your projector.

When installing or replacing the lens, make sure the Lens Model No. matches with

your projector. Refer to the catalog, or contact your sales dealer for the proper Lens

Model No.

TYPE OF THE CABINET AND INSTALLATION PROCEDURES

Refer to the Installation procedure corresponding to your projector and install the lens

correctly. (See the chart below.)

Type of the Cabinet (2) See Page 4

1AA6P1P2952-- (ICYZ)

※For use the other models (other than above cabinet), contact your sales dealer.

Some parts are not used for installation or replacement. Keep these parts for later use.

Note : Figures in this manual may be differ from the actual product.

NOTES ON LENS INSTALLATION

The ZOOM, FOCUS and LENS SHIFT adjustment on the Top Control or the

Remote Control cannot be operated with this Lens.

• Lens installation and replacement should be made by the qualified service per-

sonnel.

• Be sure to install the lens following this procedure precisely.

• The lens cover is on the lens for protection. Be sure to replace the lens cover

before installation.

• When installing or replacing the lens, be careful not to stain, scratch or damage

the lens.

After installing or replacing the lens, be sure to check the following for safety.

1. Check the lens is securely fixed by 4 screws.

2. Check no part is missing, or no mounting part is loose.

BE SURE TO CHECK FOR SAFETY

LIST OF CONTENTS

Following parts are included in the packing.

• LENS 1 pc.

• DRIVER 1 pc.

• LIGHT-BLOCK SHEET 2 pcs.

-1-

Type FE1 (Part No. 610 280 2634) For use the Type (1) Cabinet

Type FB1 (Part No. 610 285 8211) For use the Type (2) Cabinet

LENS REPLACEMENT AND INSTALLATION PROCEDURE

1. Remove screws A (2 screws).

2. Pull down the lower lens cover while pushing

the part D, then remove it.

3. Remove screws B (2 screws).

4. Remove screws C (2 screws) and remove

upper lens cover.

Fig-1

Fig-2

●IN CASE OF MODEL WITHOUT LENS

Remove 2 screws and pull down the plate.

UPPER LENS COVER

LOWER LENS COVER

COVER PLATE

REMOVE THE LENS COVER. (See figure-1)

(At the step , insert the light-block sheet in

the same position as the removed cover plate

has been placed. Two screws are not used.)

REMOVE THE COVER PLATE OF THE LENS COVER. (See figure-2)

LENS

MOTOR LEAD

CONNECTORS " K16A" and " K16B"

(D)

LENS MOTOR

Fig-3

❋Figure shown inside of the cabinet.

REMOVE THE LENS. (See figure-3.)

1. Disconnect the Lens Shift connector

“K16A”from circuit board.

2. Disconnect the Zoom and Focus con-

nector “K16B”from circuit board.

3. Loosen the A, B wire holder and

remove the lens motor lead.

4. Remove screws D (4 screws) which

fastens the lens and remove the lens.

●IN CASE OF MODEL WITH LENS

Perform the steps to for lens replacement and installation.

SCREWS

First set the lens at the center position with lens

shift adjustment.

(Type 1 Cabinet)

Disconnect the Lens Shift connector

("K16A") from circuit board. (See Fig. 3.)

-2-

MOUNT THE LENS COVER. (See figure-6)

INSTALL THE LENS. (See figure-4)

1. Remove protective caps(front and

back) on the lens.

2. Mount the lens on mounting bracket

of the main cabinet with 4 screws.

Use the screws included with the lens.

Use the driver included with the lens to

fasten the screws.

(After using, keep it for latter use.)

INSTALL THE LIGHT-BLOCK SHEET. (See figure-5)

4Install the light-block sheet around the lens

as shown in the illustration. Use the sheet

included with the lens.

Make sure the part no. and mark (TOP and

BACK) on Light-Block Sheet and set them

properly.

1. Insert the upper part lens cover and fix

them with screws A (4 screws).

2. Insert the lower part lens cover and fix

them with screws B. (2 screws).

LENS MOUNTING BRACKET

ATTACHED DRIVER

UPPER LENS COVER

LOWER LENS COVER

Fig-4

Fig-5

Fig-6

When in install the both upper and lower

lens covers, install the light-block sheet so

that it should be placed in the guide slot.

(place of the cover plate had been placed.

See figure-2.) If the installation of light-block

sheet is incorrect, it will be the cause of

leakage of light or the dust entering at the

main cabinet.

LIGHT-BLOCK SHEET

Type FE1

(Part No. 610 280 2634)

-3-

ADJUST FOCUS

Adjust focus following Focus Adjustment on

page 6.

1. Remove screws A (2 screws).

2. Push part B and pull Upper Lens Cover up.

Fig-1

Fig-2

REMOVE THE UPPER LENS COVER. (See figure-1)

(At the step , insert the light-block sheet in

the same position as the removed cover plate

has been placed. Two screws are not used.)

Perform the steps to for lens replacement and installation.

First set the lens at the center position with lens shift adjustment.

UPPER LENS

COVER

LOWER LENS

COVER

COVER PLATE

UPPER LENS

COVER

Fig-3

1. Remove screws C (4 screws).

2. Pull Lower Lens Cover toward front and

remove.

REMOVE THE LOWER LENS COVER. (See figure-2)

1. Remove screws D (2 screws) and Cover

Plate on the back of Upper Lens Cover.

REMOVE THE COVER PLATE. (See figure-3)

LENS REPLACEMENT AND INSTALLATION PROCEDURE (Type 2 Cabinet)

-4-

INSTALL THE LENS. (See figure-5)

1. Remove protective caps(front and

back) on the lens.

2. Mount the lens on mounting bracket

of the main cabinet with 4 screws.

Use the screws included with the lens.

Use the driver included with the lens to

fasten the screws.

(After using, keep it for latter use.)

INSTALL THE LIGHT-BLOCK SHEET. (See figure-6)

Install the light-block sheet around the lens

as shown in the illustration. Use the sheet

included with the lens.

Make sure the part no. and mark (TOP and

BACK) on Light-Block Sheet and set them

properly.

LENS MOUNTING BRACKET

ATTACHED DRIVER

Fig-5

Fig-6

LIGHT-BLOCK SHEET

Type FB1

(Part No. 610 285 8211)

LEAD

HOLDER

CONNECTOR

"K96S" Fig-4

DISCONNECT THE LENS SHIFT CONNECTORS. (See figure-4)

Disconnect the Lens Shift Connectors

("K96S" and "K96R") from circuit board.

CONNECTOR

"K96R"

-5-

ADJUST FOCUS

Adjust focus following Focus Adjustment on

page 6.

FOCUS ADJUSTMENT

Set up the projector and project image on the screen.

1. Loosen the Focus Lock Screw on the projection

lens.

2. Rotate the projection lens to obtain proper focus

on center area of the screen.

When the distance of the screen and lens is 1 meter,

set ●mark (yellow) of the lens on Focus Lock Screw

position.

3. Lock the Focus Lock Screw securely.

When proper focus is not observed at outer area of

the screen, proceed following adjustments.

4. Loosen the Focus Lock Ring on the projection

lens. (Turn the Lock Ring to counter-clockwise.)

5. Rotate the lens to obtain proper focus on outer

area of the screen.

6. Lock the Focus Lock Ring securely. (Turn the Lock

Ring to clockwise.)

If proper focus is not observed entire screen, repeat

above adjustment 1~ 6.

Focus Lock Screw

Focus Lock Ring

LOWER LENS

COVER

UPPER LENS

COVER

LIGHT-BLOCK

SHEET

FLAP Slide into front

of the flap.

Slide into front

of the flap.

FLAP

Slide upper both side of LIGHT BLOCK

Sheet into between and .

CABINET

GUIDE

MOUNT THE LENS COVER. (See figure-7)

1. Replace Lower Lens Cover. Slide Light-Block Sheet into the guide of Lower Lens Cover

and set them in front of the flap. (See Fig. 7.) Fix Lower Lens Cover with 4 Screws C.

(See Fig. 2.)

2. Replace Upper Lens Cover. Slide Light-Block Sheet into the guide of Upper Lens Cover

and set them in front of the flap. (See Fig. 7.) Fix Upper Lens Cover with 2 Screws A.

(See Fig. 1.)

Fig-7

●mark (yellow)

-6-

キャビネットの形状 (2)4ページ参照

1AA6P1P2952-- (ICYZ)

液晶プロジェクターレンズ

品番 LNS-W03

レンズ交換・取付作業手順書

ご注意：レンズを取り付けるまえに

レンズはご使用になるプロジェクターのキャビネットの形状により、取付部品、お

よび取付方法が異なります。取り付けるまえにキャビネットの形状をよくお確かめ

のうえ、キャビネットに合った取付作業手順にしたがい、正しくご使用ください。

レンズは液晶プロジェクターに適合した正しい品番のものをお使いください。詳し

くはカタログ、または販売店でお確かめください。

キャビネットの形状と取付作業手順

キャビネットの形状により取付作業手順が異なります。下図を参照のうえ、正しい作業

手順で行ってください。

キャビネットの形状 (1)2ページ参照

※上記形状以外の機種へのご使用については取扱販売店へご相談ください。

レンズの取り付け、または交換のあとに、お使いにならない部品が残る場合があります。

これらの部品は後日必要となる場合がありますので、大切に保管してください。

※説明文中の図は実際のものと異なる場合があります。

取り付け作業上の注意

このレンズは、リモコンまたは液晶プロジェクター本体でのズーム、フォーカス

およびレンズシフト調整はできません。

●レンズの取り付け、交換作業はサービス技術員が行ってください。

●レンズの取り付け、交換作業はこの作業手順書にしたがい、正しく行ってくだ

さい。

●レンズにはレンズ保護のためのキャップが付いています。レンズを取り付ける

まえに、かならずキャップをはずしてください。

●レンズの取り付け、取り外しのとき、レンズの表面を手でさわったり傷を付け

たりしないようご注意ください。

レンズを取り付けたあと、レンズカバーを取り付けるまえに、つぎの点検を行って

ください。

1. レンズが4本のスクリューでしっかり固定されているか。

2. 外れている部品はないか。

安全のため、必ずつぎの点検と確認を行ってください。

部品明細

梱包には以下の部品が入っています。

・レンズ本体１個

・専用ドライバー１本

・遮光プレート 2枚

型番 FE1(品番 6102802634)キャビネット形状 (1)へ使用

型番 FB1(品番 6102858211)キャビネット形状 (2)へ使用

-1-

1. スクリューＡ（2本）を外します。

2. レンズカバー下のD部を押さえ下方向に引いて外します。

3. スクリューB（2本）を外します。

4. スクリューC（2本）を外し、レンズカバーの上を外します。

レンズの交換と取り付けかた（キャビネット形状 1の場合）

レンズカバーを外す。（図1参照）

２本のスクリューを外し、プレートを下方向に引くと外れます。

（手順で遮光プレートを取り付けるとき、外したカバ

ープレートと同じ位置に差し込んでください。２本のスク

リューは不要です。）

カバープレート

●レンズなしモデルの場合

レンズカバーのカバープレートを外します。（図２参照）

図2

●レンズ付モデルの場合

レンズモーター

レンズモーターリード

Ｋ１６A,Ｋ１６Bコネクター図3

Ｂ

（Ｄ）

✽図はキャビネット内部の様子を

示しています。

レンズを外します。（図３参照）

1. 基板のレンズシフトコネクターＫ16Aを

外します。

2. 基板のズーム、フォーカスコネクター

Ｋ16Ｂを外します。

2. ワイヤーホルダーＡ，Ｂをゆるめ、レンズモ

ーターのリードを外します。

3. レンズを固定しているスクリューＤ（４本）

を外し、レンズを外します。

レンズカバー上 C

レンズカバー下

図1

レンズの交換・取り付けは〜の手順で行います。

スクリュー

基板のレンズシフトコネクターＫ16Aを外します。

（図3参照）

はじめにレンズシフトでレンズを移動範囲の中央にします。

-2-

Andere Handbücher für LNS LNS-W03

Inhaltsverzeichnis

Andere Sanyo Projektor Handbücher

Sanyo

Sanyo PLC-XF40 Bedienungsanleitung

Sanyo

Sanyo PLV-Z2 Bedienungsanleitung

Sanyo

Sanyo PLC--XP200L Bedienungsanleitung

Sanyo

Sanyo PLV-75/PLV-80 Bedienungsanleitung

Sanyo

Sanyo PDG-DWL2500 - 2500 Lumens Bedienungsanleitung

Sanyo

Sanyo PLC-WM5500/L - 5500 Lumens Bedienungsanleitung

Sanyo

Sanyo XF20 - PLC XGA LCD Projector Bedienungsanleitung

Sanyo

Sanyo PLC-WL2503A Bedienungsanleitung

Sanyo

Sanyo XGA ULTRA SHORT-THROW PLC-XL51 Bedienungsanleitung

Sanyo

Sanyo PLC-XT30 Bedienungsanleitung

Sanyo

Sanyo PLC-XU87 Bedienungsanleitung

Sanyo

Sanyo PLC-WU3800 Bedienungsanleitung

Sanyo

Sanyo PLC-XF46N Bedienungsanleitung

Sanyo

Sanyo PLC-XF45 Bedienungsanleitung

Sanyo

Sanyo PLC--XP200L Bedienungsanleitung

Sanyo

Sanyo PLC-WXU30 Bedienungsanleitung

Sanyo

Sanyo PLC-XM100/L - 5000 Lumens Bedienungsanleitung

Sanyo

Sanyo PLC-WXU300K Bedienungsanleitung

Sanyo

Sanyo PDG-DHT8000L - 8000 Lumens Bedienungsanleitung

Sanyo

Sanyo PLC-9000EA Bedienungsanleitung

Sanyo

Sanyo PJLINK PDG-DXL100 Bedienungsanleitung

Sanyo

Sanyo PLC-XF31N Bedienungsanleitung

Sanyo

Sanyo PLC-XU301 Bedienungsanleitung

Sanyo

Sanyo PLC-XT11 Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung

Epson

Epson PowerLite 810p Bedienungsanleitung