Sanyo MPR-311D(H) Bedienungsanleitung

INSTRUCTION MANUAL

Pharmaceutical Refrigerator

=MPR-311

(II)

MPR-3110(H)

---MPR-314DR{II}

MPR-311DR(H)

Note:

1. No

part

this

manual may be reproduced in

any

form

with

the expressed

written

permission

SANYO.

2. The

contents

this

manual are

subject

change

without

notice.

3. Please

contact

SANYO

any

point

this

manual is

unclear

there are

any

inaccuracies.

Japan.

CONTENTS

PRECAUTIONS FOR SAFE OPERATION

CAUTIOINS FOR USAGE

P.5

NAME AND FUNCTION OF PARTS

BEFORE COMMENCING OPERATION

P.8

AUTOMATIC TEMPERATURE RECORDER

P.10

START-UP OF UNIT

OPERATING INSTRUCTIONS

MAINTENANCE

TROUBLE SHOOTING

ENVIRONMENTAL CONDITIONS

P.15

DISPOSAL

UNIT

SPECIFICATIONS

PERFORMANCE

SAFETY CHECK SHEET

PRECAUTIONS FOR

SAFE OPERATION

It is imperative that the user

complies with this manual

contains important safety

advice.

Items and procedures are described so that

you can use this unit correctly and safely. If

the precautions advised are followed, this will

prevent possible damage to the user and any

other person.

Precautions are illustrated

the following

way:

~WARNING

Failure to observe WARNING signs

could result

a hazard to personnel

possibly resulting

serious injury or

death.

~CAUTION

Failure to observe CAUTION signs

could result

injury to personnel and

damage to the unit and associated

property.

Symbol shows;

L::,

this symbol means caution.

iSl

this symbol means

action

prohibited.

o •this symbol means

instruction must be

followed.

sure to keep this manual

a place

accessible to users

this unit.

PRECAUTIONS FOR SAFE OPERATION

~WARNING

not use the unit outdoors. Current

leakage or electric

shOck

may result

the

unit

is exposed to rainwater.

Only qualified engineers or service personnel

should install the unit. The installation

unqualified personnel may cause gas or liquid

leakage, electric shock or fire.

sure

install the unit

a sturdy floor.

the floor

not strong enough

the installation

site is not adequate, this may result

injury

from the unit falling or tipping over.

Never install the unit

a humid place or a

place where it is likely

splashed

water.

Deterioration of the insulation may result which

could cause current leakage

electric shock.

Never install the unit

a flammable or volatile

location. This may cause explosion

fire.

Never install the unit where acid or corrosive

gases are present as current leakage or

electric shock may result due to corrosion.

Make sure a dedicated power source

used

as indicated

the

rating label attached

the

unit.

Make sure to remove dust from the power

supply

plug

before inserting

a power source.

A dusty plug or improper insertion may pose a

hazard.

Use a power supply outlet with ground (earth)

to prevent electric shock. If the power supply

outlet

not grounded, it will

necessary

install a ground

qualified engineers.

Never ground the unit through a gas pipe,

water

main,

telephone line or lightening

rod.

Such grounding may cause electric shock

the case of

incomplete circuit.

not insert metal objects such as a

or a

wire into any vent, gap or any outlet for inner

air circulation. This may cause electric shock

or injury

accidental contact with moving

parts.

Never store volatile or flammable substances

this unit. This may cause explosion or fire.

Never store corrosive substances in this unit.

This may

lead

damage to the inner

components or electric parts.

Make sure to use this unit

safe area when

treating the poison, harmful or radiate articles.

Improper use may cause

bad

effect

your

health or environment.

Make sure

prepare a safety check sheet

when

you

request

any

repair or maintenance

fO!

the

safety ofservice personnel.

Always disconnect the power supply

the unit

prior

any repair or maintenance of the unit

order

prevent electric shock or injury.

Ensure

you

not inhale or consume

medication or aerosols from around the unit at

the time of maintenance. These may

harmful

your health.

Never splash water directly onto the unit as this

may cause electric shock or short circuit.

PRECAUTIONS FOR SAFE OPERATION

~WARNING

Never disassemble, repair, or modify the unit

yourself. Any such work carried out

unauthorized person may result

fire or injury

due

a malfunction.

Make the power supply to

the

unit

disconnected when the fluorescent light

replaced as this will prevent electric

S110ck.

Disconnect the power supply

plug

there

something wrong with the unit. Continued

abnormal operation may cause electric shock

fire.

the unit is to

stored unused

unsupervised area for

extended period

ensure that children

not have access

and

doors cannot

closed completely.

The disposal

accomplished of

by the unit should

appropriate personnel.

Always remove doors

prevent accidents

such as suffocation.

~CAUTION

Select a level

and

sturdy floor for installation.

This precaution will prevent the unit from

tipping. Improper installation may result

water spillage or injury from the unit tipping

over.

not install the unit where objects may fall

it.

The

electric parts are located

the upper

part of this unit.

Connect the unit

a power source

indicated

the

rating label attached to the unit. Use of

any

other voltage or frequency other than that

the

rating label

may

cause fire or electric

shock.

Fix

the

shelves securely. Incomplete

installation may cause injury or damage.

o When removing the

plug

from the power

supply outlet, grip the power supply plug, not

the cord.

PUlling

the cord may result

electric shock or fire

short circuit.

Never damage or break

the

power supply plug

or cord.

not use the supply plug

its cord

loose. This may cause fire or electric shock.

Do not touch any electrical parts such

the

power supply plug or any switches with a wet

hand. This may cause electric shock.

not put a container with water or heavy

articles

the unit. It may cause injury

falling down of

th·e

articles. Current leakage

or electric shock may

resulted from the

deterioration of insulation

spilled water.

not climb onto the unit or

not put articles

the unit. This may cause injury

turning

or damage

the unit.

PRECAUTIONS FOR SAFE OPERATION

~CAUTION

Always

hold

the handle when closing the door.

This will prevent the likelihood of a trapped

finger.

Never

lean

or press

the glass. Intentional

force may cause injury ifthe glass breaks.

not

lean

the door. This may cause

injury if

the

unit tips over.

Check

the

filter mentioned

this manual and

clean it

necessary. The dusty filter may

cause temperature rise or failure.

Never touch the condenser directly when the

filter is removed for cleaning Surfaces may

hot.

Always disconnect the power supply

plug

before moving the unit during transit. Take

care not

damage the power

cord.

The

damaged cord may cause electric shock or fire.

Dispose of water

the evaporation

try.

completely. Spilled water or splashed water

may cause current leakage or fire.

Be careful not to tip over the unit during

movement

prevent damage

injury.

Always disconnect the power plug

when

the

unit is not used for long periods.

Do not put the packing plastic

bag

within reach

children as suffocation may result.

CAUTIONS FOR USAGE

G) If the unit

unplugged or the power to the unit

interrupted,

not restart the unit for at least 5 minutes.

This protects the compressor.

® This inner cabinet

refrigerated

the forced

circulation of cooled air inside the chamber.

Ensure

that the intake and exhaust vents are not blocked.

@ Adequate space should

provided between

the

items inside the unit to allow air circulation.

@ Never store corrosive materials such as

acid

alkali unless the container

completely sealed

up.

Corrosion may lead to failure

the unit

time.

@ Once the chamber temperature has stabilized,

put

the items into the chamber

small batches

minimize the temperature increase.

® Fix the shelves securely. Place items

the

shelves

and

leave a space between the walls of

the

cabinet

and

the contents

allow air circulation.

not place items

the floor ofthe chamber.

(J)

When

the

power plug-in the unit, the fan does

not

always operate immediately. After a few minutes,

the

fan operates properly.

® For some time after

the

unit has been started, or

when the ambient temperature

fairly high, the cabinet

walls may heat

up.

This does not indicate a

malfunction. It indicates that the dew

preventative/power economy function

performing

satisfactorily. Hot gases are piped from the motor

compressor along the front edges of the cabinet to

prevent dew condensation.

@ If condensation forms

the front glass

frame

surface, wipe it off with a soft, dry cloth.

not clean the unit with scrubbing brushes, acid,

thinner, solvents, powdered soap, cleanser

hot water.

These agents

can

scratch the paint or cause it to peel.

Plastic and rubber parts

can

easily damaged by

these materials, especially solvents. When a neutral

detergent

used

clean

the unit, rinse thoroughly

with a cloth soaked

clean

water.

!TIl

instrument requiring a power source is to be

placed inside the cabinet, the cable

can

led through

the access port

the

left hand side of the cabinet.

After installation, a rubber cap should

used

seal

the access

port.

Failure to

this

can

affect the

temperature uniformity inside the cabinet and lead to

condensation

the outside ofthe access port.

Caution for model with

mark

This unit is equipped with the circuit breaker

the

back. Make sure this breaker is switched ON

before the unit is started to run.

When

the operation

the unit is stopped by this

breaker, contact a dealer

a service station after

disconnected the power supply plug.

•

Circuit

breaker

t:JZ::;:::r-

Never disassemble, repair, or modify the unit

yourself. Any

such

work carried out

unauthorized person may result

fire

injury

due

a malfunction.

Disconnect the power supply

plug

if there is

something wrong with the unit. Continued

abnormal operation may cause electric shock

or fire.

Connect the unit

a power source as indicated

the rating

label

attached

the unit. Use of

any other voltage or frequency other than that

the

rating

label

may cause fire or electric

shock.

NAME AND FUNCTION OF PARTS

.-.

ii~r

..""'''

---

(Q)

IIIII

MPR-311D(H)

([)

Door

Consists

double pair glass with heat

ray

reflection

film.

® Frame (Product unit)

@ Fluorescent lamp

20W

white light. For replacement, refer to page

13.

@ Air circulating fan

Circulate the cooled air

chamber.

(Q)

Air intake vent

@ Air exhaust vent

Monitoring hole

This hole allows cables to be passed into the cabinet.

@Lock

® Circuit breaker install position

,..

r-;c-

..L

i @

;

, -

-®

\lJ

1-,@

I~@

@Caster

Drawer

.L~

-_._

.•

--<.

MPR-311DR(H)

For moving

the unit. At the time

installation, use

the height adjusting screw to level the unit.

® Height adjusting screw

Adjust the height

screw bolt used to level and install

the unit.

@ Door switch (MPR-311D(H) only)

@ Temperature recorder install position

@ Evaporating tray

Place

rear bottom

the frame. Pull out forward for

removing.

@Shelf

@ Control panel

® Thermometer (MPR-311(H) only)

NAME AND FUNCTION OF PARTS

IControl panel

0 0 0

\,0

" 0

DEFROST

.-_:.All

._.

TeMP.

CONTROL

UGHT

MPR·311(H)

®@@

@ ®

sll

0 0 0 0 0

'ow

DEFROST

w,'m.

o~.

.=.

.~-

lEMPERATIJRE

lEMP.

CONTROL

UGHT

MPR·311D(H), MPR·311DR(H)

Buzzer switch (BUZZER)

sliding this switch to OFF position, the buzzer can

be silenced when the alarm is activated.

® Defrost lamp (DEFROST)

This lamp is lit during defrosting.

@ High temperature alarm lamp (HIGH TEMP.)

This lamp is lit during high temperature alarm condition.

@ Door check lamp (DOOR)

This lamp is lit when the door is open. (MPR·311D(H),

MPR·311DR(H))

@ Digital temperature display

This indicator shows the chamber temperature or set

temperature. (MPR·311D(H), MPR·311DR(H))

@ Set button (PUSH SET)

The set temperature

displayed while this button is

pressed. (MPR·311D(H), MPR·311DR(H))

r:v

Temperature control knob

This knob is for setting a desired temperature.

® Fluorescent lamp switch (LIGHT)

To turn

the light, keep

pressing this switch until

the both sides

a fluorescent lamp is lit. To turn off

the light, press this switch again.

® Power supply lamp

This lamp is lit when the power is supplied to the unit.

(MPR·311(H) only)

BEFORE COMMENCING OPERATION

Installation site

To operate this unit property and

obtain maximum performance, install the unit

a location with the following

conditions.

A location notsubjected to direct sunlight

Installation

a location subjected

direct sunlight

may

lead·

inadequate cooling.

® A location with adequate ventilation

Leave at least 10cm around the unit for ventilation.

Poor ventilation result

a reduction ofthe refrigeration

capability.

@ A location far from heat generating sources

Avoid installing the unit near heat-emitting appliances

such as gas ranges or stoves. Heat

can

cause.

inefficient refrigeration.

@ A location with a sturdy and level floor

&'WARNING

oBe sure to install the unit

a sturdy floor.

If the floor is not strong enough or the

installation site

not adequate, this may

result

injury from the unit falling or tipping

over.

~CAUTION

oSelect a level and sturdy floor for

installation. This precaution prevents the

unit from tipping. Improper installation

may result

water spillage or injury from

the unit tipping over.

Install the unit

a sturdy floor

avoid vibration

and noise. Placing the unit

unsteady floor

will cause vibration

and

noise.

@ Alocation not prone to high humidity

&'WARNING

not use the unit outdoors. Current

\.Y

leakage or electric shock may result if the

unit

exposed

rainwater.

Never install the unit

a humid place or a

\.Y

place where it is likely to

splashed

water. Deterioration

the insulation may

resultwhich could cause current leakage or

electric shock.

not install the unit under the piping for

\.Y

water main and lor vapor. Deterioration of

. the insulation may cause current leakage

or electric shock.

@ A location without a flammable

corrosive gas

&'WARNING

Never install the unit near a flammable or

\.Y

volatile location. This may cause

explosion or fire.

Never install the unit where acid or

\.Y

corrosive gases are present as current

leakage or electric shock may result due to

corrosion.

Andere Handbücher für MPR-311D(H)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sanyo Kühlschrank Handbücher

Sanyo

Sanyo SR-3770S Bedienungsanleitung

Sanyo

Sanyo SRR-72GD-MED - Lab & Pharmacy Refrigerator 61 cu.... Bedienungsanleitung

Sanyo

Sanyo MPR-721 Bedienungsanleitung

Sanyo

Sanyo SR-2570M Bedienungsanleitung

Sanyo

Sanyo SR-3720M - Counter-High Refrigerator Bedienungsanleitung

Sanyo

Sanyo HF-5017 - Counter-High Freezer Montageanleitung

Sanyo

Sanyo MBR-1404G Bedienungsanleitung

Sanyo

Sanyo SR41XC Bedienungsanleitung

Sanyo

Sanyo MPR-411FR Bedienungsanleitung

Sanyo

Sanyo MPR-1014 Bedienungsanleitung

Sanyo

Sanyo BLOOD BANK MBR-304DR Bedienungsanleitung

Sanyo

Sanyo SR1031W - Refrigerator 10.3CF 2Door Frost... Bedienungsanleitung

Sanyo

Sanyo SR-3720M - Counter-High Refrigerator Montageanleitung

Sanyo

Sanyo SR-257 Bedienungsanleitung

Sanyo

Sanyo SRA-1780 - Commercial Solutions Freezerless Compact... Bedienungsanleitung

Sanyo

Sanyo SR-S52TW Bedienungsanleitung

Sanyo

Sanyo SR-6100K Betriebsanleitung

Sanyo

Sanyo SRA-1780 - Commercial Solutions Freezerless Compact... Bedienungsanleitung

Sanyo

Sanyo SR4310W - Commercial Solutions Refrigerator Bedienungsanleitung

Sanyo

Sanyo SR-361W Leitfaden

Sanyo

Sanyo MPR-1411 Bedienungsanleitung

Sanyo

Sanyo SR-1030 Bedienungsanleitung

Sanyo

Sanyo SRA2480 - Commercial Solutions Freezerless Compact... Bedienungsanleitung

Sanyo

Sanyo SR-6100S - Commercial Solutions - General-Purpose Laboratory... Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung