Sanyo C29LF37 Bedienungsanleitung

SERVICE MANUAL Colour Television

Product Code: 111376504

Original Version

Chassis Series: LB4-C

C8AE

FILE NO.

Model No. C29LF37

Service Ref. No. C29LF37-00

(Argentina)

Give complete “SERVICE REF. NO.” for parts

order or servicing. It is shown on the rating

plate at the cabinet back of the unit.

This T.V. receiver will not work properly in

foreign countries where the television trans-

mission system and power source differ from

the design specifications.Refer to the specifi-

cation table.

POWER

Specifications

Power Source . . . . . . . .AC220V, 50Hz / 60Hz

Receiving System . . . . .PAL (M/M, N/N), NTSC (M/M)

Channel Coverage

Antenna mode VHF: CH02-CH13, UHF: CH14-CH69

CATV mode VHF band: CH01-CH13, Mid band: CH14-CH22

Super band: CH23-CH36, Hyper band: CH37-CH64

Ultra band: CH65-CH94 and CH100-CH125

Low mid band: CH95-CH99

Video IF . . . . . . . . . . . . .45.75MHz

Aerial Input Impedance 75Ω

Input Terminals

AV1 (Video): Composite Video Input (Phone Jack) x 1

S-Video Input (SeparatedY/C) DIN 4-pin Jack x 1

AV1 (Audio):L/R Stereo Input (Phone Jack) x 1 set

AV2 (Video):Composite Video Input (Phone Jack) x 1

AV2 (Audio):L/R Stereo Input (Phone Jack) x 1 set

AV3 (Video): Component Y, CB, CRInput (Phone Jack) x 1 set

AV3 (Audio): L/R Stereo Input (Phone Jack) x 1 set

Output Terminals

Video Monitor Output: Phono jack x 1

Audio Monitor Output: L/R Stereo Output (Phone Jack) x 1 set

Headphone Jack: Mini stereo jack x 1

Sound Output (RMS) . . . 5W + 5W

Speaker . . . . . . . . . . . . . 6cm x 12cm x 2 pcs.

Dimensions . . . . . . . . . . 749(W) x 585(H) x 486(D)mm

Weight . . . . . . . . . . . . . . approx. 41.5 Kg

Specifications subject to change without notice.

Contents

-2-

Safety Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chassis Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

IC Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

Service Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18

Cabinet Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Chassis Electrical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-30

Safety Notice

SAFETY PRECAUTIONS

1: An isolation transformer should be connected in the

power line between the receiver and the AC line

when a service is performed on the primary of the

converter transformer of the set.

2: Comply with all caution and safety-related notes pro-

vided on the cabinet back, inside the cabinet, on the

chassis or the picture tube.

3: When replacing a chassis in the cabinet, always be

certain that all the protective devices are installed

properly, such as, control knobs, adjustment covers

or shields, barriers, isolation resistor-capacitor net-

works etc.. Before returning any television to the

customer, the service technician must be sure that

it is completely safe to operate without danger of

electrical shock.

X-RADIATION PRECAUTION

The primary source of X-RADIATION in television receiver is the picture tube.The picture tube is specially con-

structed to limit X-RADIATION emissions.For continued X-RADIATION protection, the replacement tube must be

the same type as the original including suffix letter. Excessive high voltage may produce potentially hazardous X

- RADIATION.To avoid such hazards, the high voltage must be maintained within specified limit.Refer to this ser-

vice manual, high voltage adjustment for specific high voltage limit. If high voltage exceeds specified limits, take

necessary corrective action. Carefully follow the instructions for + B1 volt power supply adjustment, and high volt-

age check to maintain the high voltage within the specified limits.

PRODUCT SAFETY NOTICE

Product safety should be considered when a component replacement is made in any area of a receiver.

Components indicated by mark in the parts list and the schematic diagram designate components in which

safety can be of special significance. It is particularly recommended that only parts designated on the parts list

in this manual be used for component replacement designated by mark . No deviations from resistance

wattage or voltage ratings may be made for replacement items designated by mark .

Chassis Block Diagrams

-3-

T611A

Q432

IC501

LA78041

VERT-OUT

T471

IC802

IC801

CPU

TUNER

SAW

IC201

IC3401

MTS DECODER

IC001

AUDIO

AMP.

SDA SCL

ON-TIME

POWER ON/OFF

BLK

OSD

SDA

SCL

X161

A101

ANT

IF-IN

5/6

SCL

SDA

BLK

12 11 14 15 16 17

FM OUTPUT

COMP. VIDEO OR

Y-IN

K1301 K1002

REAR AV3-IN (DVD-IN)

& MONITOR OUT

FRONT AV2-IN

VIDEO AUDIO-L AUDIO-R

POWER

CIRCUIT

CONVERTER

TRANS

140V (MAIN HIGH)

28V (AUDIO)

12V (MAIN LOW)

25V (VERT)

REG.

5V RC

2723

HORIZ-OUT

FBT

VERT.OUT

HORIZ.OUT

EEPROM

Q901

CRT

FILTER

(WITH PLL)

IIC BUS CONTROL

IF/VIDEO/CHROMA/DEFLECTION

HEADPHONE JACK

AUDIO RIGHT

AUDIO LEFT

5/6

AV SELECTOR

IC1001

K1302

AV1-IN

AUDIO-R

VIDEO

S-VIDEO

AUDIO-R

VIDEO VIDEO

19/20 37

3/5/6 10

323334 13 14 16

S-C IN

3839

42 40

234 35

IC701

SP902

SP901

VIDEO OUT (TV)

VIDEO

MONITOR

OUT

AUDIO MONITOR

OUT (L)

AUDIO MONITOR

OUT (R)

TV AUDIO

(R)

TV AUDIO

(L)

AUDIO-L

AUDIO-L AUDIO-R

AUDIO-L

S-VIDEO IN

AV1 VIDEO IN

AV1 AUDIO-L IN

AV1 AUDIO-R IN

CRIN

CBIN AV3 VIDEO IN

AV3 AUDIO-L IN

AV3 AUDIO-R IN

AV2 VIDEO IN

AV2 AUDIO-L IN

AV2 AUDIO-R IN

SELECTED AUDIO (R) IN

SELECTED

AUDIO (L) IN

C OUT

IC681

REG.

IC202

IC203

5V-2,4

5V-3,5

TO IC801

PIN-15

FROM IC1001

PIN-37

COMP. VIDEO (CAPTION) IN

MAIN SIGNAL PROCESSING CIRCUIT

IC801

CPU

QXXAVC545P

X801

OSC

CPU OSC IN

CPU OSC OUT

SOUND MUTE OUT

(MUTE = HIGH)

IC001

AUDIO AMP.

RESET IN (RESET = LOW)

KEY SWITCH IN

KEY

SWITCH

RC PRE-AMP.

RC SIGNAL IN

(ON = HIGH)

RELAY OUT FOR DEGAUSSING

LED

(TIMER ON = LOW)

ON TIMER LED OUT

MEMORY

IC802

SDA

SCL

LED

RED

POWER CIRCUIT

TUNER

A101

SDA

SCL

IC3401

MTS

IC201

IF/VIDEO/CHROMA/DEF.

AFT S-CURVE IN

COMPOSITE VIDEO SIGNAL

(C-CAOTION) IN

OSD BLK OUT

OSD RED OUT

OSD GREEN OUT

OSD BLUE OUT

DEFLECTION

CIRCUIT

HORIZ. SYNC. IN

VERT. SYNC. IN

POWER CIRCUIT

etc.

POWER PROTECTION IN

(POWER ERROR=LOW)

GREEN

POWER ON/OFF (STANDBY=LOW)

IC1001

AV SELECTOR

(ACTIVE = HIGH)

SDA

SCL

SDA

Chassis Block Diagrams

-4-

SYSTEM CONTROL

IC Block Diagrams

-5-

IC201 < IF/Video/Chroma/Def. > LA76828

VOL

DET

23456

AGC

VIF

8910

VCC 5V 11 12 13

BUS

PEAKING

CORING BLACK

STRETCH

SYNC

SEP

14 15

ABL

REST

CLAMP

OSD

CONTRAST

BRIGHT

16 17 18 19 20

CONTRAST

BRIGHT RGB

MATRIX

OSD

DRIVE/OUT-OFF

VCC 21 22 23

FSC/

SYNC SW

24 25 26 27

VER

RAMP HOR

VCCH

VCC

VER

C/D

HOR

OUT

PHASE

SHIFTER

AFC2

AFC1

VER

SEP

HOR

C/D

1/256

COLOR

CLAMP

LPF

ALC

CLAMP

DEMO

PAL

ACC

BPF

ON/OFF

DELAY

LINE

TRAP

AFT

VIDEO

DET

TRAP

LIM

AMP

BPF

SPLL

BPF

VIDEO

AMP

VIDEO

SW APC1 TINT

VXO DDS APC2

CLAMP

VCO

1H DELAY

HOR

VCO

FBP

2829

32 1H

VCC

353637

CLMP

4445

CLMP

V/C VCC

4950

A2C

PLL

525354

Audio Output

FM Output/Selected

Audio Output

PIF AGC

RF AGC Output

PIF Input1

PIF Input 2

IF Ground

IF Vcc

FM Filter

AFT Output

Bus Data

Bus Clock

ABL

Red Input

Green Input

Blue Input

Fast Blanking Input

RGB Vcc

Red Output

Green Output

Blue Output

E/W Output

Vertical Output

Ramp ALC Filter

Horizontal/BUS Vcc

Horizontal Output

Horizontal AFC Filter

Flyback Pulse Input

VCO IREF

Clock (4MHz) Outupt

CCD Vcc

CCD Filter

CCD/Horizontal Ground

SECAM B-Y Input

(Cb Input)

SECAM R-Y Input

(Cr Input)

Chroma APC2 Filter

Clamp Filter

4.43 MHz Crystal

Chroma APC1 Filter

fsc Output

Video/Vertical/BUS Ground

External Video Input(Y-IN)

Video/Vertical Vcc

Internal Video Input (S-C IN)

Black Level Detector

Video Output

VCO Filter

VCO Coil 2

VCO Coil 1

APC Filter

Ext. Audio Input

SIF Output

SIF APC Filter

SIF Input

S.TRAP

OVER

MOD.

DC ADS.

IC Block Diagrams

-6-

IC001 < Audio AMP. > LA4270-E

Thermal

Protection

+AMP

Pump

INVERTING

INPUT

Vcc

PUMP UP

OUT

GND

Ver. OUTPUT

OUTPUT

STAGE Vcc

NON INV.

INPUT

IC501 < Vertical Output > LA78041-E

CH1

CH2

Thermal

Shutdown

Over

Voltage

Ripple

Filter

30K

300

30K

300

Vcc

Feedback 1

Input 1

Ripple filter

Input side

earth

Input 2

Feedback 2

Output 2

Output side

earth

Power supply

Output 1

LA4270

12345678910

IC1001 < AV Selector > MM1313BD

MTV-V

V1-V

V2-V

V3-V

STV-V

0dB 0dB

V1-Y

V2-Y

V1-C

V2-C

MTV-L

V1-L

V2-L

V3-L

STV-L

MTV-R

V1-R

V2-R

V3-R

STV-R

BIAS

SCL

SDA

BIAS

30GND

I2C LOGIC 28

24 ROUT2ROUT2

ADDRESS

Mute

-6dB

6dB

32 ROUT1

LOUT1

LOUT2

-6dB

39 COUT1

CIN1

YOUT1

VOUT2

YIN1

34 VOUT1

6dB

38 Vcc

6dB

-6dB

COMB

IC Block Diagrams

-7-

VDD VDD VDD

VDD

MIRROR 2

VDD

FLASH-

DIODE

VOC

Inverting

Input

(3x)

1,2,3

9,8,7

VDD

Non-inverting

Input

Vip

MIRROR 1

Vbias

MIRROR 3

LEVEL-

SHIFTER 1 LEVEL-

SHIFTER 2

DIFFERENTIAL

STAGE

CURRENT

SOURCES

GND

THERMAL

PROTECTION

Note: One amplifier shown.

Cathode

Output

(3x)

IC701 < Triple Video Output Amplifier > TDA6103Q/N3

10 11

LFLT VCO

PCINT1

PCINT2

PLINT

13 VCA LPF

FLT

COMPIN

Vcc

Analog Block GND

23NOISETC

SAPTC

14 15

VGR

IREF

765

I2C BUS I/F

Digital Block GND

SCL

SDA

SAPIND

NOISE

DET

SAPVCO

BPF

STIND

1/4 1/2

LPF

DeEm LPF

LPF

DeEm

AMP

(+4dB) LPF

24 25 22

SAPOUT

SAPIN

STIN

26 27 28

VEWGT

LPF

HPF

LOGIC

NRSW/FOMO/SAPC

VCA

21 9

SUBOUT

(L-R signal output)

MAIN OUT

(L+R signal output)

MATRIX

VE VCA

RMSDET

29 30 32 31 1

VETC

VEOUT

VCAIN

VCAWGT

VCATC

TREBLE OUT-L

SPECTRAL

34 33

FEXT1

TVSW

EXT1/EXT2/M1

SURR

SURROUND

BASS

TREB

BASS

TREBLE

TREB

VOL-L

VOL-R

VOLIN-L

LSOUT-L

LSOUT-R

VOL-R

VOLUME RIGHT

CHANNEL INPUT

TREBLE OUT-R

TREBLE FILTER-L

BASS FILTER-L

40 SURRTC

38 TVOUT-R

39 TVOUT-L

37 AUX2-L

(Left channel

external input)

FEXT2

INPUT PIN OF (L+R)

SIGNALFROM

MAIN OUT(PIN9)

(+6dB)

WIDEBAND

"STEREO"

"NOISE"

"SAP"

"PONRES"

ATT/ATTSW

BASS FILTER-R

(Stereo block

PLL loop filter

integrating

pin)

(Pilot cancel

circuit loop filter

intergrating pin)

(Audio multiplexing

signal input)

AUX2-R

(Right channel

external input)

TREBLE FILTER-R

AUX1-L(Left channel

external input)

AUX1-R(Right channel

external input)

(Band gap reference

output)

(Sap FM detector

output)

(Input of L-R signal

from SUBOUT)

(Input of SAP signal)

(Variable de-

emphasis

integrating pin)

(Variable de-emphasis

output pin)

IC3401 < MTS Decoder, Audio Control & Switch > CXA2134Q-T6

TV/AV

VOL +

VOLUME +

VOLUME

CHANNEL UP

CHANNEL DOWN

S1.00110111 S2.01111000

ADDRESS DATA

02 H-PHA 16

Item No. Item Data value

General

This set has an On-screen Service Menu system included in the CPU that allows remote operation for most of the

service adjustments.

2. Service Adjustments:

Press the CHANNEL UP/DOWN button on the remote

control handset to select the desired service menu

item you want to adjust.

Use the VOLUME + /

button to adjust the data.The

+ or

button will increase or decrease the data

sequentially.

3. Exit from the Service Menu

Press the MENU button to turn off the Service Menu

display.

The data which is set in the service mode is stored

into the memory IC automatically.

[ Service Mode Display ]

Service Adjustment-1

1. Enter the Service Menu

While pressing the MENU button on the television, press the Number Key 2on the remote control unit.

The Service Menu now appear.

IC802 (EEPROM) Replacement

When IC802 (EEPROM) is replaced, IC801 (CPU) will automatically write the initial reference data into IC802 for basic TV operation.

However, the bus data should be checked and some bus data should be set up before attempting the service adjustments. (See

pages 9 ~ 12 for detailed information.)

Initial Bus Data Setup

Note: When IC802 (EEPROM) is replaced, following Service Menu should be set up for proper TV operation before attempting the

service adjustments.

NO.01 RFAGC (Adjust the data 11 to 14) NO.23 EWCBM (Adjust the data 08 to 11) NO.87

ZOMCON (Adjust the data -6 to -8)

NO.02 H-PHA (Adjust the data 10 to 14) NO.27 EWTLN (Adjust the data -4 to -1) NO.121

POMT (Adjust the data 05 to 12)

NO.05 V-SCO (Adjust the data 16 to 23) NO.28 EWCTPN (Adjust the data -3 to -1) NO.125 CCD (Adjust the data 20 to 30)

NO.06 V-LIN (Adjust the data 30 to 28) NO.29 EWCBN (Adjust the data -5 to -2) NO.09 V-S60 (Adjust the data -1 to -3)

NO.11 VLI60 (Adjust the data +1 to 0) NO.43 B-YD (Adjust the data 08 to 09) NO.129

EWCTPZ (Adjust the data +1 to +5)

NO.17 OSDHP (Adjust the data 30 to 40) NO.53 RBAG (Adjust the data 08 to 09)

NO.18 OSDC (Adjust the data 18 to 30) NO.56 RBAGN (Adjust the data -2 to 0)

NO.19 EWDC (Adjust the data 44 to 35) NO.58 RBDN (Adjust the data -2 to -5)

NO.20 EWAMP (Adjust the data 16 to 19) NO.60 RBBDN (Adjust the data 03 to 00)

NO.21 EWTL (Adjust the data 28 to 30) NO.61 COGV (Adjust the data 00 to 03)

NO.22 EWCTP (Adjust the data 07 to 09) NO.62 BLKS (Adjust the data 01 to 00)

Service Adjustments

-8-

-9-

Service Adjustments

No. Item Initial value Range Description

01 RFAGC 11→14∗00~63 RF AGC adjustment

02 H-PHA 10→14∗00~31 H-PHASE adjustment (50Hz)

03 V-POS 40 00~63 Vertical position adjustment (50Hz)

04 V-SIZ 46 00~127 Vertical size adjustment (50Hz)

05 V-SCO 16→23∗00~31 Vertical-S compensation (50Hz)

06 V-LIN 30→28∗00~31 Vertical linearity adjustment (50Hz)

07 H-P60 +4

16~+15 Difference value of H-PHASE adjustment (60Hz)

08 V-P60 0

32~+31 Difference value of V-POSITION adjustment (60Hz)

09 V-S60

1→

3∗

64~+63 Difference value of V-SIZE adjustment (60Hz)

10 VSC60 +4

16~+15 Difference value of Vertical-S compensation (60Hz)

11 VLI60

16~+15 Difference value of Vertical linearity adjustment (60Hz)

12 H-PHAZ -1

16~+15 Difference value of H-PHASE adjustment (Zoom)

13 V-SZZ5

64~+63 Difference value of V-SIZE adjustment (Zoom, 50Hz)

14 V-SCOZ 0

16~+15 Difference value of Vertical-S compensation (Zoom)

15 V-LINZ 0

16~+15 Difference value of Vertical linearity adjustment (Zoom)

16 V-SIZZ6

64~+63 Difference value of V-SIZE adjustment (Zoom, 60Hz)

17 OSDHP 30→40∗01~255 OSD horizontal position

18 OSDC 18→30∗00~127 OSD contrast

19 EWDC 44→35∗00~63 EW DC (50Hz), Horizontal width adjustment

20 EWAMP 16→19∗00~63 EW Amp. (50Hz)

21 EWTL 28→30∗00~63 EW Tilt (50Hz)

22 EWCTP 07→09∗00~15 EW corner top (50Hz)

23 EWCBM 08→11∗00~15 EW corner bottom (50Hz)

24 EWAMZ -9

32~+31 Difference value of EW Amp. (Zoom, 50Hz)

25 EWDCN 0

32~+31 Difference value of EW DC (60Hz)

26 EWAMN -2

32~+31 Difference value of EW Amp. (60Hz)

27 EWTLN -4→-1∗

32~+31 Difference value of EW Tilt. (60Hz)

28 EWCTPN -3→-1∗

8~+7 Difference value of EW corner top (60Hz)

29 EWCBN -5→-2∗

8~+7 Difference value of EW corner bottom (60Hz)

30 EWAMZN -8

32~+31 Difference value of EW Amp. (Zoom, 60Hz)

31 EWCOR 0 0, 1 EW COR SW

32 V-SCP 07 00~07 V-SIZE COMP

33 H-SCP 07 00~07 H-SIZE COMP

34 SBIAS 70 00~127 Sub Bias adjustment

35 RBIAS 00 00~255 Red Bias adjustment

36 GBIAS 00 00~255 Green Bias adjustment

37 BBIAS 00 00~255 Blue Bias adjustment

38 RDRIV 64 00~127 Red Drive adjustment

39 GDRIV 08 00~15 Green Drive adjustment

40 BDRIV 64 00~127 Blue Drive adjustment

-- -- --

White balance (a lateral line)

42 DRV

-- --

Brightness and dark of White balance adjustment

43 B-YD 08→09∗00~15 B-Y DC Level

44 R-YD 08 00~15 R-Y DC Level

45 B-YDN -1 -16~+15 Difference value of NTSC/PAL-M B-Y DC Level

46 R-YDN 0 -16~+15 Difference value of NTSC/PAL-M R-Y DC Level

47 B-YDD -1 -16~+15 Difference value of DVD B-Y DC Level (50Hz)

48 R-YDD -2 -16~+15 Difference value of DVD R-Y DC Level (50Hz)

49 B-YDD6 -1 -16~+15 Difference value of DVD B-Y DC Level (60Hz)

50 R-YDD6 -2 -16~+15 Difference value of DVD R-Y DC Level (60Hz)

On-screen Service Menu

Following table shows the initial values which have been stored in the CPU ROM, and items for the service adjustments.

When IC802 (EEPROM) is replaced, check the bus data to confirm they are the same as below.The shaded menu should be checked

and be set up or readjusted according to the procedures described in the following pages.

Initial Setup Data marked with an ∗should be changed from Initial Value Data.

-10-

Service Adjustments

No. Item Initial value Range Description

51 G-YA 00 00,01 G-Y Angle

52 RBGB 10 00~15 R-Y/B-Y Gain Balance

53 RBAG 08→09∗00~15 R-Y/B-Y Angle

54 G-YAN 00 00,01 Difference value of NTSC G-Y Angle

55 RBGBN +4 -8~+7 Difference value of NTSC R-Y/B-Y Gain Balance

56 RBAGN -2→0∗-8~+7 Difference value of NTSC R-Y/B-Y Angle

57 RBADP +2 -8~+7 Difference value of DVD PAL R/B Angle

58 RBDN -2→-5∗-8~+7 Difference value of DVD NTSC R/B Angle

59 RBBDP +2 -8~+7 Difference value of DVD PAL R/B Balance

60 RBBDN 03→00∗00~15 Difference value of DVD NTSC R/B Balance

61 COGV 00→03∗00~03 Coring gain

62 BLKS 01→00∗00~03 BLK. STR. start (W/Defeat)

63 BLKG 00 00~03 BLK. STR. gain

64 BRTA 00 00, 01 BRT. ABL Defeat

65 BRST 00 00, 01 Mid. Stp. Defeat

66 BRTH 00 00~07 Bright. ABL.Threshold

67 WPL 00 00~03 WPL Ope. Point (W/Defeat)

68 YGAM 00 00~03 Y Gamma Start

69 PORW 00 00, 01 AV Mode Pre/Over SW

70 PORS 02 00~03 AV Mode Pre/Over-shoot adjustment

71 RFCO 0 -2~+1 Difference Value of RF Corring Gain

72 PORWN 01 00, 01 RF Pre/Over SW

73 PORSN 03 00~03 RF Pre/Over-shoot adjustment

74 TINT +10 -16~+15 Tint

75 SHRF 00 -16~+15 Difference Value of RF Sharpness

76 SHRFD 00 -16~+15 Difference Value of DVD Sharpness

77 CODP -10 -16~+15 Difference Value of DVD PAL colour

78 CODN 0 -16~+15 Difference Value of DVD NTSC colour

79 RFCOL -7 -16~+15 Difference Value of TV colour

80 TIDN +8 -16~+15 Difference Value of DVD NTSC tint

81 SHRFS 00 -16~+15 Difference Value of S-terminal Sharpness

82 TISN 00 -16~+15 Difference Value of S-terminal NTSC tint

83 COSPN 00 -16~+15 Difference Value of S-terminal colour PAL-N

84 COSPM 00 -16~+15 Difference Value of S-terminal colour PAL-M

85 COSN 00 -16~+15 Difference Value of S-terminal colour NTSC

86 ZOMCOL -6 -16~+15 Difference Value of Colour (Zoom)

87 ZOMCON -6→-8∗-16~+15 Difference Value of Contrast (Zoom)

88 ZOMBRI -6 -16~+15 Difference Value of Brightness (Zoom)

89 TEXC +8 -64~+63 OSD TEXT Contrast

90 AUFL 00 00~01 Auto. Flesh

91 COOP 07 00~07 Colour Killer option

92 Y-APF 01 00, 01 Y-APF Select

93 DEEM 00 00, 01 De-emphasis TC

94 V-LVL 04 00~07 Video Level

95 FMLVL 16 00~1F FM Level

96 TTEST 00 00~07 Trap Test

97 IFOM-S 00 00, 01 Over Modulation SW

98 IFMN-S 00 00, 01 Audio Monitor SW, Monitor or FM

99 IFTRPS 00 00, 01 IC Built-in SIF Trap ON/OFF

100 IFMLVL 136 00~255 Video Level Coarse Adjustment & Modulation Operating Dot Setting

101 VBSW 00 00, 01 VBLK SW

102 FBTS 00 00, 01 FBP Blanking SW

103 HBLKL 05 00~07 H-Blanking Control Left

104 HBLKR 03 00~07 H-Blanking Control Right

105 AFCRF 00 00, 01 Adjustment of AFC Gain & Gate (RF)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sanyo Fernseher Handbücher

Sanyo

Sanyo LCD-32XH3 Bedienungsanleitung

Sanyo

Sanyo CP29AF2X Bedienungsanleitung

Sanyo

Sanyo DP32649 - 32" LCD TV Bedienungsanleitung

Sanyo

Sanyo DS35510 Bedienungsanleitung

Sanyo

Sanyo DS32224 Bedienungs- und Wartungshandbuch

Sanyo

Sanyo 28DN2F Bedienungsanleitung

Sanyo

Sanyo C28W1 Bedienungsanleitung

Sanyo

Sanyo CE32LD81-B Bedienungsanleitung

Sanyo

Sanyo DP26649 - 26" LCD TV Bedienungsanleitung

Sanyo

Sanyo CZP3012 Bedienungsanleitung

Sanyo

Sanyo DS27930, DS32424 Bedienungsanleitung

Sanyo

Sanyo DS27510 Bedienungsanleitung

Sanyo

Sanyo C29LK41S Bedienungsanleitung

Sanyo

Sanyo CP29EF3 Bedienungsanleitung

Sanyo

Sanyo CP34ST3T Bedienungsanleitung

Sanyo

Sanyo AVM-2751S Bedienungsanleitung

Sanyo

Sanyo CE14SP4R Bedienungsanleitung

Sanyo

Sanyo LCD-37XR1 Bedienungsanleitung

Sanyo

Sanyo CP21VF1 Bedienungsanleitung

Sanyo

Sanyo CE28SN3-C Bedienungsanleitung

Sanyo

Sanyo 25BN1 Bedienungsanleitung

Sanyo

Sanyo CE28DF1-C Bedienungsanleitung

Sanyo

Sanyo AVM-3651G Bedienungsanleitung

Sanyo

Sanyo CZP2515V Bedienungsanleitung

Beliebte Fernseher Handbücher anderer Marken

Philips

Philips Colour Television Bedienungsanleitung

Toshiba

Toshiba 27A10 Bedienungsanleitung

Philips

Philips 42PF9630A/37 Bedienungsanleitung

Hitachi

Hitachi 32FX48B Bedienungsanleitung

DAEWOO ELECTRONICS

DAEWOO ELECTRONICS DTQ-14V1FC Bedienungsanleitung

Changhong Electric

Changhong Electric uhd55b6000is Bedienungsanleitung

Philips

Philips Matchline 21CE7551 Bedienungsanleitung

Panasonic

Panasonic Genus TX-G10 Bedienungsanleitung

Toshiba

Toshiba 19A20 Bedienungsanleitung

Philips

Philips 25PT4523-16 Bedienungsanleitung

Sony

Sony XBR-100Z9D Bedienungsanleitung

Philips

Philips PR0930X3 Bedienungsanleitung

Philips

Philips Brilliance 231P4QPY Bedienungsanleitung

Samsung

Samsung 55S9 B Series Bedienungsanleitung

Philips

Philips 32HF9385D Fehlerbehebungshandbuch

Sharp

Sharp LC-40FI5012E Bedienungsanleitung

Loewe

Loewe Table Stand Reference 55 Bedienungsanleitung

Philips

Philips 32PFH5300 Bedienungsanleitung