Sanyo A11H Series Gebrauchs- und Pflegehandbuch

This procedure contains instructions for replacing the battery pack that is installed in the UPS main unit.

When the battery pack arrives, check the model number shown in the packaging box.

U P S Battery Pack Voltage

MODEL No. Mass

A11H102* BPA11H102A00 Appox. 6 kg 24V

A11H152* BPA11H152A00 Appox. 9 kg 36V

A11H202*011US

A11H202*011USTW

A11H202*111USTW

BPA11H202A00

BPA11H202A01 Appox.12 kg 48V

A11H302*011US

A11H302*011USTW

A11H302*111USTW

BPA11H302A00

BPA11H302A01 Appox.16 kg 60V

＜

Appearance of battery pack

＞

CAUTION

！

Please replace the battery periodically. Batteries that have expired the replacement period may cause a fire.

The weight of the battery pack is shown in the table. Please wear insulated gloves, safety shoes when replacing the battery. Be

careful not to injure yourself; dropping it into your feet or pich your hands when handling the battery pack. Bodily injury may iccur if

not properly handled. Replacing the battery for A11H302 model should be done by two or more people. Please protect your back to

avoid back pain.

The voltage that is listed in the table above is always occuring on the battery terminal, so do not touch them with your hands or

short-circuit them. There is a risk of electrick shock or injury. Also, for safety, use insulation method, such as attaching vinyl tape to

the used battery pack connector.

To safely replace the battery pack, please refer to the A11H insturction manual.

M0011840

※

It is not covered by our warranty if the damage is caused by an agent other than our company during replacement. When

replacing the battery performed by an agent other than our company, shall be responsible for the damage done.

※

Damage includes damage to equipment and load equipment, data damage and loss profits. However, it is not only limited to

these.

A11H battery pack is especially designed for our UPS. Do not use a non-specified battery. Also, do not mix old batteries to new one

or use batteries with different manufacturing date. It may cause battery life shortage, leakage and heat generation.

Note on battery replacement

※

The packaging box is used to send back the used battery

pack, so do not dispose it.

Scale

A11H302

Battery pack

A11H102

Battery pack

A11H152

Battery pack

A11H202

Battery pack

①

Check the state of usage

②

Replace the battery pack with the following procedure depending on the state of the load device connected to the A11H.

Continued on page 3.

If you can stop the load equipment

Replace the battery pack.

⇒

１．

Replacing the battery pack

If the load device cannot be stopped.

※

You can also replace the battery pack

without stopping the load. However, it is

recommended that you do it in a short

period of time because you will not be

able to back up when an input

abnormality such as a power outage

occurs during replacement

A11H stop.

For more information on stopping

procedures, please refer to

A11H’s Instruction Manual

Stop the load equipment.

If the

A11H*U

model is used as a UL Standard Product

and CE Marking Conformity Product

, you may not

be able to replace the battery pack by yourself due to a standard restriction. Be sure to ask a service

representative

CAUTION

Use as UL Standard

Please ask a service representative

Exchange the battery

Reset the battery information.

⇒

．

Resetting the Battery Information

Fill in the next battery replacement.

⇒

．

[Caution for Storage Battery Replacement ] Label

Start A11H

Please refer to the

instruction manual of A11H

for details of the startup

procedure.

Start the load equipment.

Dispose the used battery pack.

⇒

．

Disposing of the Used Battery Pack

（

）

If the battery pack is defective, discontinue use and contact the retailer or our company.

（

）

Battery storage and charging of the battery

・

Battery disintergrate during storage, so please use as soon as possible.

・

Store the battery in a dry place where the temperature is low.

・

During storage, please charge once at least every 6 months (storage temperature: 25

℃

)

and before use.

・

Please charge with the UPS charger. Refer to A11H Owner’s Manual “Charging the UPS”

（

）

Battery Transportation and Handling

・

As a rule, avoid abnormal vibrations or shock during transportation.

・

Do not use a battery pack that has been accidentally dropped, or a battery pack that has been strongly impacted.

Handling Precautions for Battery Pack

Replace the battery pack.

⇒

．

Replacing the Battery Pack

．

Replace the battery pack with the following steps.

①

Remove the UPS front cover.

②

Remove the one screw on the right side of the battery cover and remove the battery cover.

③

Set the Forced Bypass Switch to “Bypass” side.

④

Unplug the battery connector.

⑤

Pull out the battery pack.

For Rack Type

Caution

！

The weight of the battery pack is shown in the table on page 1. The battery pack

does not have a drop stopper. Pull the battery pack slowly, hold t

he bottom with

both hands, and be careful no to drop it. Also, be careful no to pinch your hands

when dealing with battery packs.

The A11H302 battery pack has a scale at the top shown on page 1. When the

scale is seen, keep the bottom part supported with both hands, and be careful

not to drop it.

①

Remove by sliding in

the direction of the

arrow by holding two

places of strongly.

Battery Cover

②

Loosen the screw and slide the

battery cover in the direction of the

arrow. The screw is a fall prevention

screw, so it can’t come off the

battery cover.

⑤

Pull out the battery

pack out.

④

Disconnect the battery connector.

⑥

Attach

the tape and insulate it.

For service personnel only

③

Slide the switch to

｢Bypass｣

When it is not used as a UL

Specification

When it is used as a

UL Standard.

(Authorized person only)

Procedures

③、⑨

and

⑩

are

required for UL Standards

For Tower Type

（１ｋＶＡ）

（2ｋＶＡ

3ｋＶＡ

）

⑥

Remove the tape from the battery connector on the new battery pack and attached it to the used battery pack connector.

⑦

Insert the new battery pack into the UPS.

⑧

Plug in the battery connector.

②

Loosen the screw and slide

the battery cover in the

direction of the arrow. The

screw is a fall prevention

screw, so it can’t come off

the battery cover.

For service personnel only

③

Slide the switch to

｢Bypass｣

⑤

Pull out

the battery

pack out.

④

Disconnect the battery conn

ector.

⑥

Attach the tape and insulate

it.

For service personnel only

③

Slide the switch to

｢Bypass｣

④

Disconnect the battery

connector.

⑥

Attach the tape and

insulate it.

⑤

Pull out the battery pack out

①

Remove by sliding in

the direction of the arrow

by holding two places of

strongly.

①

Remove by sliding in the

direction of the arrow by

holding two places of

●

strongly.

②

Loose the

screw, slide the battery cover

up, and pull forward.

For Rack Type

For Tower Type

（１ｋＶＡ）

（2ｋＶＡ

3ｋＶＡ

）

Caution

！

Do not force to insert the battery connector if it is in a

different orientation. Damage to the connector may cause

electric shock.

Be careful not to pinch your hands when securing the

cover.

Types of Battery Pack Where to insert

BPA11H202A00

①

BPA11H202A01

②

③

BPA11H302A00

①

BPA11H302A01

②

③

The diagram shows the case of A11H102.

The size of the battery pack depends on the model.

Please see the size on page 1.

If you have an additional battery module, replace the

battery after

⑧

⑦

Insert the battery pack

in the direction of the

arrow.

⑧

Ｐ

lug in the battery connector until you

hear a click sound.

⑧

Ｐ

lug in the battery connector until you

hear a click sound.

The diagram shows the case of A11H202.

The size of the battery pack depends on the model.

Please see the size on page 1.

⑦

Insert the battery pack

in the direction of the

arrow.

If you have an additional battery module, replace the battery

afte

r ⑧.

①

②

③

※ ③

is exclusively used by A11H202*111USTW and

A11H302*111USTW.

⑨

Set the switch Forced Bypass to

｢

Inverter

｣

side.

⑩

Make sure that LED

【

OUTPUT green

】

and

【

INV.ON/STAND BY

green

】

on the front panel are blinking.

Press for over a second.

⑪

Confirm the switch Forced Bypass is on the

｢

Inverter

｣

side, the LED

【

OUTPUT green

】

and

【

INV.ON/STAND BY

green

】

the front panel are lit (when the UPS is in operation).

⑫

Install the battery cover.

⑬

Fit the front cover

When it is not used as a UL

Standard.

When it is used as a UL Standard

(for service personnel)

When it is used as a UL Standard and CE Marking

Conformity Product (for service personnel)

For Rack Type

For Tower Type

（１ｋＶＡ）

（2ｋＶＡ

3ｋＶＡ

）

⑬

Push the front

cover until the claw

hook to the left side.

For service personnel only

⑨ ⑪

Slide the switch

｢Inverter｣.

⑫

nsert the tabs into the slots and

slide it to the right until you hear a

click sound. Secur

e it with the

screws.

If the

Forced Bypass

is on

｢

Bypass

｣

side, set it to

｢

Inverter

｣

side

。

If the UPS is in operation, the

【

INV.ON/STAND BY

green

】

is blinking

、

Press for 1 second and

check if

【

INV.ON/STAND BY green

】

turns on, then

proceed to step

⑫.

Caution

For service personnel only

⑨ ⑪

Slide the switch

｢Inverter｣.

⑫

Insert the tabs into the slots and slide it down until

you hear a click sound. Secure it with the screws.

⑬

Attach and slide the front

cover in the direction of the

arrow until the claw hook.

⑬

Attach and slide the front

covers in the direction of the

arrow until the claw hook.

⑫

Insert the tabs into the slots and slide it down until

you hear a click sound. Secure it with the screws.

For service personnel only

⑨ ⑪

Slide the switch

｢Inverter｣.

Press

３～４

seconds and

release it

when the buzzer rings

「

beep, beep

」

２

２．

．

Reset the Battery information after replacing the battery installed in the UPS. The following actions will reset all battery information (such

as expected battery lifetime, battery operating time, power outage count, etc.): If you have additional batteries, do so after replacing all

the battery packs.

①

Make sure the UPS is in the following state.

②

Press for

３～４

seconds and release it when the buzzer alarms.

③

Promptly press the (3 second or less) several times until the five LEDs enclosed by are in the blinking pattern as shown

in the figure.

④

Promptly press the (3 second or less) several times until the four LEDs with are in the blinking pattern shown in the

figure.

Press promptly

Reset the battery information after

replacing the

battery. If you do this incorrectly

, the battery life warning

will not display correctly.

The MAIN SW on the back side is set to

「

」

※１

【

INV.ON/STAND BY green

】

and

【

OUTPUT green

】

are

not blinking.

※２

UPS is in user setting mode

Buzzer:

「

beep, beep

」

Either

【BATT.LOW】

【25】

is blinking or both

：【INPUT】

Blinking

：

Off

：

Blinking

Indicator

。

※１

can be operated either

｢

｣

｢

OFF

｣

state.

※２

．

blinking, the

Forced Bypass

switch is set to

｢

Bypass

｣

.Set it to

｢

Inverter

｣

and operate again.

POINT

Every time you press or

the blinking pattern changes.

If you push too far and slip through the LED blinking pattern

you want to select, press repeatedly until the LED blinking

pattern you want to select again appear.

POINT

Example

：

LED blinking pattern when set the setting value to

reset

Setting Value

LED blinking

pattern Details

Do not reset

● ○ ○ ○

Do not reset

Reset

○ ● ○ ○

Reset Battery Information

Reset the battery information (expected battery lifetime,

battery operating time, power outage count, battery life LED

indication) after replacing the battery.

Initial Setting

Please release it as soon as the buzzer alarms

「

beep, beep

」

, it

means that the setting is saved in the

ＵＰＳ

and resume to

normal operation.

After resetting, the setting are automatically returned to

「

Do not reset

」

⑤

ress for

３～４

seconds and release it when the buzzer alarms.

【BATT.LOW】

is still blinking, the battery information i

s not reset

correctly. Please reset it again.

Caution

Press

３～４

second

s and

release it when the buzzer rings

「

beep, beep

」

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sanyo UPS Handbücher

Sanyo

Sanyo SANUPS A11J Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung