Sartorius L2200S Bedienungsanleitung

Sartorius Laboratory.

L 610, L2200S, L2200P

Electronic Precision Balances

Installation and Operating Instructions

Advanced Test Equipment Rentals

www.atecorp.com 800-404-ATEC (2832)

1 Weighing pan

2 Weight display

3 ON/OFF key

4 CAL key

5 Tare control

6 Menu access switch (for the balance operating program)

7 Leveling foot (L 2200 S only)

8 Power receptacle

9 level indicator (L 2200 only)

Sartorius Laboratory

L 610, L 2200 S, L 2200 P

With this Sartorius Balance, you have acquired a sophisticated,

high-quality electronic precision weighing Instrument that will

help ease your daily work load.

Please read these Installation and operating instructions care-

fully before operating your new balance.

Pursuant to the German Directive for the Implementation

of Regulations for Prevention of Accidents "Elektrische

Anlagen und Betriebsmittel (VBG 4)" [Electrical Installa-

tions and Equipment] of April, 1986, it is hereby certified

that the equipment delivered, "Electronic Precision Bal-

ance, model L 610, L 2200 S or L 2200 P," is manufac-

tured and tested in compliance with the following

DIN/VDE regulations

DIN IEC348/VDE0411:

Safety requirements for electronic measuring apparatus

DIN IEC 380/VDE 0806:

Safety of electrically energized Office machines

DIN IEC 601 A/DE 0750:

Safety of medical electrical equipment

and with Article 10 of the Low Voltage Directive

73/23/EEC issued on February 19, 1973, by the Euro-

pean Community.

When you use electrical equipment in installations and

under ambient conditions requiring higher safety Stan-

dards, you must comply with the provisions as specified

in the applicable regulations for installation in your coun-

try.

Contents

Equipment Supplied 5

Installation Instructions 6

Startup 7

Operation 8

Calibration 10

Balance Operating Program 11

Troubleshooting Guide 14

Accessories 15

Specifications 17

Equipment Supplied

Do not miss out on the benefits of our warranty.

Please complete the warranty registration card, indicating the

date of installation, and return the card to your Sartorius dealer.

The equipment supplied includes the components shown on the

left and a dust cover.

Save all parts of the packaging and the box for shipping your

balance to prevent any damage during transportation.

Installation Instructions

Ambient Conditions

Please choose a suitable place to set up your balance. lt should

not be exposed to the following:

— heat radiation

— aggressive/corrosive substances

— vibrations

— draughts

Do not expose the balance to extreme moisture over long peri-

ods. Moisture in the air can condense on the surfaces of a cold

balance whenever it is brought to a substantially warmer place.

lf you Transfer the balance to a warmer area, make sure to

condition it for about 2 hours at room temperature, leaving it

unplugged. Afterwards, if you leave the balance connected to

mains power supply, the continuous positive difference in tem-

perature between the inside of the balance and the outside will

practically rule out the effects of moisture condensation. The

components used in the balance are rated to at least Class KSF

according to DIN 40040.

Startup

Attach the dust cover by pressing down on the adhesive disks,

and mount the weighing pan (1) on the balance.

Your balance is powered by an AC adapter. Please make sure

that the voltage rating printed on this unit is identical to your lo-

cal line voltage rating.

Plug the cord of the AC adapter into the power receptacle of the

balance. Secure the connection by tightening the knurled collar.

Now plug the AC adapter into a wall outlet.

At the point of use, level the balance using the leveling feet (7)

so that the air bubble is entered within the circle of the level in-

dicator (9) (only for the L 2200 S).

Operation

The weight display provides the following special Status mes-

sages for your information:

BUSY

The processor is still busy processing a function and will not ac-

cept any other commands to perform functions at this time.

STANDBY

The display has been turned off with the ON/OFF key (3), and

the balance is now in the STANDBY mode and ready to operate

without

warm u p.

POWER OFF

The balance was disconnected from line power (reconnection to

line power after the balance was unplugged, power failure).

CAL

The calibration function has been activated.

In addition to grams, this balance gives you a variety of

other menu-definable international weight unit options.

Select the weight unit you need from the table of the menu op-

tions for the balance operating program, and set the appropriate

code as described in the section "Balance Operating Program."

Press the ON/OFF key (3) to turn the display on or off.

You can also turn it on with the tare control (5).

After the balance has been plugged into the AC adapter, the

weight display will go out whenever you turn oft the power with

the ON/OFF key. All other electronic circuits will remain ener-

gized (indicated by STANDBY). This means the balance is im-

mediately ready to operate without requiring warmup the next

time you switch it on.

After the power is turned on, a test of all essential electronic

functions is run automatically.

This self-test ends with the readout 0.00 g (it the program code

setting 511 is used).

Now place your sample or object on the pan (1) to determine

the weight. Read oft the weight in the display (2) as soon as the

weight unit (in this case "g") appears as the stability symbol.

lf you wish to use a Container to weigh, or if the weight display

does not indicate 0.00 g (or the equivalent with the weight unit

of your choice), press the tare control to zero the display.

Calibration

— This is only possible with an accurate calibration weight

(L 610 - 500 g; L 2200 S, L 2200 P - 2,000 g).

— See the "Accessories."

Clear the pan and press the CAL key (4) for at least three sec-

onds until the calibration weight readout appears in the display.

Center the calibration weights on the pan.

Now the weight unit symbol is displayed. An acoustic signal

indicates the end of the calibration procedure.

Balance Operating Program

The balance operating program lets you adapt your balance to

various ambient conditions and to different weighing require-

ments, and select the weight unit(s) commonly used in your

country. At the factory, we have set the codes for a Standard

program, which is protected by a locking function to prevent ac-

cidental changes.

The "menu code" contains the information of the operating

program, lt consists of three digits, known as the page (1st

digit), the line (2nd digit) and the word (3rd digit) in "com-

puterese."

How to access the menu of the balance operating program:

With the balance turned off (STANDBY state), hold down the

tare control (5) and briefly press the ON/OFF key (3).

Upon completion of the automatic self-test, release the tare

control as soon as "CH5" is displayed. The Status of the bal-

ance operating program will appear in the weight display:

"L" Stands for the list mode. In this mode, you can check the

menu code settings, but you cannot program new menu codes.

lf you wish to change a program menu code, you must first

unlock the menu access switch to access the program menu.

To do so, remove the protective cap located on the front right of

your balance and slide the menu access switch (6) in the direc-

tion of the arrow.

The display will indicate "C," which Stands for the change

mode, meaning you can now change the menu code settings.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sartorius Skala Handbücher

Sartorius

Sartorius Combics CAW3P Bedienungsanleitung

Sartorius

Sartorius Secura 224-1S Bedienungsanleitung

Sartorius

Sartorius 1802 Benutzerhandbuch

Sartorius

Sartorius Master series Bedienungsanleitung

Sartorius

Sartorius 2406 Benutzerhandbuch

Sartorius

Sartorius la series Bedienungsanleitung

Sartorius

Sartorius CPA 12001S Bedienungsanleitung

Sartorius

Sartorius LE series Bedienungsanleitung

Sartorius

Sartorius CAPXS Series Bedienungsanleitung

Sartorius

Sartorius QC34EDE-S Bedienungsanleitung

Sartorius

Sartorius Cubis MCA Series Bedienungsanleitung

Sartorius

Sartorius Economy Series Bedienungsanleitung

Sartorius

Sartorius combics 1 Bedienungsanleitung

Sartorius

Sartorius PMA.Evolution Bedienungsanleitung

Sartorius

Sartorius mc1 Bedienungsanleitung

Sartorius

Sartorius MC 5 Bedienungsanleitung

Sartorius

Sartorius IS 300 IGG-H Bedienungsanleitung

Sartorius

Sartorius PMA.Evolution Bedienungsanleitung

Sartorius

Sartorius MW1 Bedienungsanleitung

Sartorius

Sartorius YDK 01 Bedienungsanleitung

Sartorius

Sartorius PMA7501-Y00G Bedienungsanleitung

Sartorius

Sartorius TS 12 Bedienungsanleitung

Sartorius

Sartorius EA Bedienungsanleitung

Sartorius

Sartorius PMA.Quality PMA7501H Bedienungsanleitung

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung