Sartorius MC 210 S Bedienungsanleitung
98648-004-81
Sartorius Micro
Analytical, Semi-micro- and Microbalances
Installation and Operating Instructions
0–0
Contents
Page
General Views of the Balances:
MC 210 S, MC 210 P and
MC 410 S (-0CE) 1– 0
General Views of the Balances
MC 5 (-0CE) and SC 2 (-0CE) 1– 2
Warranty 1– 4
Storage and Shipping Conditions 1– 4
Transporting the Balance 1– 5
Equipment Supplied 1– 7
Installation Instructions 1– 8
Using Verified Balances
Approved as Legal Measuring
Instruments in the EU 1– 9
Getting Started 1–10
General Instructions for
“Analytical Weighing” 1–16
Weighing Electrostatically
Charged Samples
and Containers 1–16
Weighing Magnetic
or Magnetizable Samples 1–17
General Instructions for Handling
Samples and Containers 1–18
Operating the Balance 1–19
Balance Display 1–19
Turning the Display On and Off 1–20
Self-Test 1–20
Opening and Closing the
Draft Shield 1–21
Simple Weighing 1–26
Taring 1–26
Weighing Range Structure 1–27
Weighing in the IQ-Mode 1–28
Mass Unit Conversion by Toggling
1–29
Displaying the Balance Model
and the Serial Number 1–29
Page
Calibration/Adjustment and
Linearization Functions 1–30
Data Interface 1–36
Below-Balance Weighing 1–37
Fastening an Antitheft
Locking Device 1–37
Troubleshooting Guide 1–38
Care and Maintenance 1–40
Servicing 1–40
Cleaning the Balance Housing 1–40
Cleaning the Weighing Chamber 1–40
Safety Precautions 1–41
Balance Operating Menu 2– 1
Weighing in Three Ranges
on Standard Balances 2– 7
Weighing in Two Ranges
on Verified Balances Approved
for Use as Legal
Measuring Instruments 2–10
Display Modes for
Standard Balances 2–11
Display Modes for Verified
Balances Approved for Use
As Legal Measuring Instruments 2–13
Calibration Functions on
Standard Balances 2–14
Calibration Functions on Verified
Balances Approved for Use
as Legal Measuring Instruments 2–16
Utilities for Printouts
or Data Transfer 2–18
Additional Functions 2–21
ISO/GLP-compliant Printout
or Record 2–25
Setting the ID No./Date/Time 2–30
0–1
Page
Application Programs 3– 1
Functions Common to
All Programs 3– 3
cKey 3– 3
Information and Printouts
or Data Transfer 3– 4
Data ID Code K* or NUM 3– 4
“EUREKA” Air Buoyancy
Correction Program 3– 5
Differential Weighing and
Backweighing 3–14
Weighing Sequence 3–15
Selecting the Memories 3–17
Key Functions 3–18
Clearing the Memory 3–31
Density 3–34
Diameter Determination 3–42
Tare Memory 3–44
Weighing in Percent 3–47
Over/Under Checkweighing 3–51
Counting 3–55
Error Codes 3–59
Page
Interface Description 4– 1
Pin Assignment Chart 4–19
Cabling Diagrams 4–20
Specifications 5– 1
English Translation of the
EC Type-Approval Certificate
for MC 5-0CE 5– 6
Accessories (Options) 5– 7
Declarations of Conformity 6– 1
Index 7– 1
Supplement:
Brief Operating Instructions
General View of the Balances:
MC 210 S, MC 210 P and MC 410 S (-0CE)
1–0
1–1
1 Large draft shield cover
2 Small draft shield cover
3 Exterior draft shield element,
semicylindrical
(can be moved by hand)
4 Interior draft shield door,
semicylindrical (can be moved by
motor control or by hand)
5 Interior weighing chamber
draft shield only on MC 210 S,
MC 210 P (-0CE)
6 Protective ring
7 Weighing pan
8 Protective disk
9 Leveling foot
10 Level indicator
11 Display unit
12 AC jack/power socket
13 Menu access switch
14 Data interface port
15 Terminal for connecting an
equipotential bonding conductor
16 Lug for attaching an antitheft
locking device
17 Metrological ID label for verified
balances approved for use as legal
measuring instruments
18 Manufacturer’s label
19 Application display
20 Numeric keys
21 ffunction key
22 Ffunction key
23 rand ldraft shield
function keys
24 p Print key (data transfer)
25 Function display for the
fand F keys
26 tTare key
27 Application program display
28 Weight display
29 wtoggle key
30 Info key
31 ON/OFF key e
32 ckey
33 Bar graph (range indicator)
34 Verification ID label with
metrological data for verified
balances approved for use
as legal measuring instruments
General View of the Balances:
MC 5 (-0CE) and SC 2 (-0CE)
1–2
34
35
36
10
7
9
8
37
1–3
7 Weighing pan
8 Protective disk
9 Leveling foot
10 Level indicator
11 Display and control unit
12 AC jack
13 Menu access switch
14 Data interface port
15 Terminal for connecting an
equipotential bonding conductor
16 Lug for attaching an antitheft
locking device
17 Metrological ID label for verified
balances approved for use as legal
measuring instruments
18 Manufacturer’s label
(on bottom of balance)
19 Application display
20 Numeric keys
21 ffunction key
22 Ffunction key
23 rand ldraft shield function keys
(for opening and closing)
24 p Print key (data transfer)
25 Function display for
the fand F keys
26 tTare key
27 Application program display
28 Weight display
29 wtoggle key
30 Info key
31 ON/OFF key e
32 ckey
33 Bar graph (range indicator)
34 Draft shield
35 Weighing cell
36 Inner draft shield
37 Below-balance weighing port
38 Male connector on weighing cell
39 Male connector on computing
device
40 Electronic computing device
Please read these installation and operating
instructions carefully before you begin to operate your
new balance.
Warranty
Do not miss out on the benefits of our full warranty.
Please contact your local Sartorius office or
dealer for further information. If available, complete
the warranty registration card, indicating the date
of installation, and return the card to your Sartorius
office or dealer.
Storage and Shipping Conditions
Allowable storage temperature: +5°C ... +40°C
+41°F to +104°F
The complete packaging has been designed to ensure
that the balance will not be damaged even if it is
dropped from a height of 80 cm (about 31inches).
After unpacking the balance, please check
it immediately for any visible damage as a result
of rough handling during shipment.
If this is the case, proceed as directed in the section
entitled “Safety Inspection.”
Save all parts of the packaging and the box for
your balance to avoid damage during
transportation. Ship your balance only in the
complete original standard packaging supplied.
The packaging consists of the following:
– 2 boxes
– 3 polystyrene inserts
– 2 polypropylene pads
The inner packaging is not suitable for shipping
because it provides the balance little protection from
blows. Before packing your balance for shipment,
unplug all connected cables to prevent damage.
Do not expose the balance unnecessarily to extreme
temperatures, moisture, shocks, blows or vibrations.
1–4
Transporting the Balance
To transport the balance, lift it by the housing base
using both hands. Never lift your balance by grasping
the display unit or the draft shield!
Transport Arrestment
Before unplugging the balance from the power
supply or unplugging the connecting cable, turn off
the balance using the ekey (31).
For MC5 (-0CE) and SC 2 (-0CE):
After approximately 10 seconds, the balance will
be arrested, or locked, for transportation.
While the balance is raising the weights after you
have turned it off, the symbol “Mot” from a calibration
or linearization procedure is displayed.
Warmup Time
Condition your balance for 12 hours to the temperature
of a new location. After initially connecting the
balance to AC power (or after a relatively long power
outage), allow it to warm up for at least 2 hours.
Each time you move your balance to another location,
you must condition it for at least 12 hours to the
new location.
After initially connecting the balance to AC power
(or after a relatively long power outage), allow the
balance to warm up for at least 2 hours.
1–5
Note to Users of Verified Balances Approved for Use
as Legal Measuring Instruments:
Linearization after Transport
After transport, the linearity and calibration of your
balance may be out of the permissible tolerances
(see the “Specifications”). Always carry out internal
linearization of the balance after transport.
Repeating this procedure – several times, if necessary –
enhances the linearization. This procedure is described
on page 1–35.
Preparing a Verified Balance for Use as a Legal
Measuring Instrument:
After initially connecting the balance to AC power
(or after a relatively long power outage), allow
it to warm up for at least 24 hours.
1–6
Dieses Handbuch passt für folgende Modelle
10
Inhaltsverzeichnis
Andere Sartorius Skala Handbücher
Sartorius
Sartorius BL150S Bedienungsanleitung
Sartorius
Sartorius Secura Bedienungsanleitung
Sartorius
Sartorius Entris Bedienungsanleitung
Sartorius
Sartorius Micro MC Series Bedienungsanleitung
Sartorius
Sartorius Factory Series FC06BBE-S Bedienungsanleitung
Sartorius
Sartorius PMA35001-Y Bedienungsanleitung
Sartorius
Sartorius 2405 Benutzerhandbuch
Sartorius
Sartorius Entris II BCA Advanced Series Bedienungsanleitung
Sartorius
Sartorius PMA.Quality PMA7501 Bedienungsanleitung
Sartorius
Sartorius L2200S Bedienungsanleitung
Sartorius
Sartorius PMA.Power Series Bedienungsanleitung
Sartorius
Sartorius PMA 7501-X Bedienungsanleitung
Sartorius
Sartorius Cubis MCE Series Bedienungsanleitung
Sartorius
Sartorius Entris II Technisches Datenblatt
Sartorius
Sartorius Cubis MCA Series Bedienungsanleitung
Sartorius
Sartorius Entris BCE Series Bedienungsanleitung
Sartorius
Sartorius Signum 1 Bedienungsanleitung
Sartorius
Sartorius IW2P1x-6ED-L Bedienungsanleitung
Sartorius
Sartorius Factory Series Bedienungsanleitung
Sartorius
Sartorius IS 150 IGG-H Bedienungsanleitung
